we have a PtMP scenario in which we want to stop client to client wireless traffic as lots of them are causing congestion in the network... can any body tell how we can do this in mikrotik software.
first of all congratulations on the job. Want to know if you have used Nstreme protocol, can you please send comlpete details relating to this, like: 1. if you have used then what was your configuration at both ends, 2. if not then didnt you face ack-timeout issue for sucha long link also, can you d...
Hi, we have installed XR2 card for distribution on a PIV system with 512Mb RAM , we have about 60-70 clients connecting to this and getting between 128-256kbps connections. we are getting very high latency and regular RTOs. Amazingly signals are good ack-timeout is on dynamic and varies between 30-5...
can you please tell us what ack-timeout value we should use for 2-b/g/10/5 bands for different distances, is there any specific formulae we should follow?
can you guide and elaborate on this a little more.
hi, I have 133(3-card board) I put only one SR2 in it and keep normal setting like band :2.4 b/g and scan it will scan for 5-6 seconds and router restarts, this time the router doesnt detects SR2, so I restarts it again, (this time manually) and this time SR2 is back online I again change band from ...
XR2 shows 18dbm only, i read in a topic that this is because of a driver error from 'madwifi' and it is ok , the tested power is 28dbm, i cannot question that but explain the following scenario(table test): WLM54Ag on RB532 scan result : SSID Signal strength KCTEST -42 Infozee -86 default -85 XR2 on...
hi, would like to know if any one has tried the following scenarios with stability: WLM54AG (BH) & XR2 (distribution) on 133 WLM54AG (BH) & SR2 (distribution) on 133 Also, I am facing a very strange problem on 133 board with the second scenario on table test when i scan SR2 card for wireless...
we are using 133 boards with 50mtr CAT6 cable and 18v 1.1A POE getting frequent RTOs and latency , is any one facing this probelm, by using of 24v 1.0A adapter help us out. please let me know.
we just put one XR2 in our 133board and the default power it is showing is just 18dbm can you confirm if you are getting the same thing , also in bench test the signals of XR2 were quite high as compared to Sr2 let me know some details regarding this, if you can
there is a very strange problem on 133 coming up that site is being able to ping but it is not opening on IE it says 'website found ...' thats it and doesnot open , please help our ISP link is down and we are facing lot of problem.
I have a point to point link as follows: RB112+NMP-8602+48vPOE ---------45kms------- WRAP.2E + SR2 +18v POE between 2100-2200hrs the link quality drops between -85 to -90 , whereas normally it hovers around -65 to -72 , Can anybody tell what the problem can be??? I mean the whole day it works perfec...
MPERDUE->
which card is ar5211 that you were using? isnt it a chipset of atheros or a model no. , please send complete manufacturing detail if you can and MAC address if possible.
want to know what will you go for, because on the paper 133 looks better more interfaces more RAM more storage (NAND), which do you think is better in performance?
Can 133 handle power requirement , if we install three high power cards?
my TDMs have finally got in sync with radios (NSTREME - DUAL) but there is no transmission of voice at the remote end can someone tell me what the problem is???
hi,
TDMs are working finally without any breakage in Ethernet signal but latency is high , in cross over cable the latency was about 46ms constant, in case of wireless it varies between 47-73ms just wanted to know if this is ok???
sorry for late response i was out of town...thanks for your suggestion we will test the whole scenario as you explained and with the equipmn we are going to use
we are tryig to carry E1 signal from TDM over IP device to a remoe area 3km away but we are not getting any throughput for E1, whereas in wireless circuit we are getting well over 6Mb, on futhe analysis we saw that on transmission of data the Rxor Tx always go below 2Mb(which is E1 ofcourse) and we ...
this is just for example... buildings are about 9 storeys high some are 16 stories... ALL made of concrete and bricks ....lots of windows on each of the four side there are about 10offices on each floor about 900sqft. IF POSSIBLE THE WHOLE AREA.. 2.4 here is conjysted is like trying to walk with a b...
Hello everyone, you might have guessed from the subject what the question is .... is there any way to provide wireless broadband solution in a city type scenario (Non-line of site of course) say in 4-city blocks on Mikrotik. What is OFDM really?? and is it Non or Near LOS ?? Can anyone send me some ...