i tried it befor i wrote in the Forum.
I have this problem for a Long time and i have until now not found a solution.
The Problem is somewhere else.
In the Forum i read about other customers who have the same problems.
Dear Sir/Madam, We are looking for an Administrator for LAN/WAN Networks. We are a German regional leading Internet Company. We provide Internet and Telephone Services to our customers. As a rapidly strong expanding company with a huge potential, we are looking for a suitable employee. Qualification...
Hello, I have a great problem. My customers (MT in client wds mode) are connected to the Acess point (MT) with WDS. If a customer connect at the AP now, because he had lost the connection to the AP or he turned the terminal equipment on, all other users get a very high ping and time out. What can be...
Hello, I have a problem several with ASUS Mainboard of the type P5VDC. I operate an Intel 2.6 GHz Celeron CPU with 512 MB of RAM save at this board. I have operate two RouterBOARD 14 boards with 8 WLAN interfaces,too. The problem is, that the system hangs itself up and does not react any more. None ...
hello gpienaar how you solve the problem with the ip pool for pppoe. I have the same net structure. unfortunately, I have a problem with the ip addresses. how I can solve it, that 12 AP with a pppoe server grasping on one ip pool. we forgive the customers dynamic ip addresses. The logon is carried o...
Hello, I have a throughput of approx. 18 MB/s if I connect 3 MT servers (PC) about wireless and let these go in the wds mode (bridge). If I let the net with ospf go, I get 12 MB/s throughput only. (MT1 -- MT3) I get a bandwith of 17 MB/s if data flow from MT1 to MT2. I get a low bandwith if data flo...
how can I solve the scenario mentioned above with OSPF and PPPOE?
Must be configured only the PtP ways with OSPF or I must also with ospf configure the sector aerials for costumers?
Can help with somebody?
Hello Freebird I will make it as follows. I will BS1 let bridges mode go in this. WLAN1, 2, 3 and ethernet interface = bridge. I will make the other stations also in a bridge. Sector and p2p aerials. The customer equipment also becomes (bridged WLAN and Ethernet interface) At the pppoe server I esta...
I have asked a question and had to notice tonight that this was removed.
why?
It was all about pppoe problems and enquired where one can download an older mikrotik version.
I would like to give public IP's to the customers. With wds bridge about dhcp I assign an IP to the customer equipment. get the customer also an address assigned by my server?(ethernet side) I would not like this. The customer should not be able to access my network at all best. this is I believe th...
have I understood it correctly?
Must I all interfaces bridges?
BS2 must run about wds with BS1.
the Sectorantennas at BS2 are just the same in WDS mode.
And the client Routerboard are in WDS mode,too.
Is this correctly?
Every customer gets a Routerboard 532.
How I shall this configure?
I mean WLAN1 and ethernet I must bridges, so that the customer can dial in with his computer about pppoe.
Is this correct?
BS1 is the Main AP. this passes the signal on to Bs 2, 4 and 5. I would like a transparent network, so my idea. I do not know now whether this idea is good. on all radio towers apart from BS1 are sector aerials. These care for the customers. Understand I this correctly, I must bridges interface if I...
Hello, I have the following scenario. I have several radio towers which pass the signal of place for place on. I would like the customer to dial in about pppoe now. I wanted to use EoIP for it. How I shall the particular adjust radio towers? Shall I bridge the interfaces for every station? Bs 1 is t...
I have my network public IP at this run now.
It works wonderfully. (almost)
I must open sebarate port for every customer.
How I create it, to give public IPs with open ports?
Making the large providers like it.
Hello, I have a problem public ip it. my Internet connection has 8 ip adressen. (xxx.xxx.xxx.xxx/29) I have got 128 new IP addresses now and wanted to use these. (NAT 1:1) The ip addresses' area is xxx.xxx.xxx.xxx/25 how can I solve this? if I an IP address give the Internet interface to, this is at...
I would like an aerial (5 GHz, 28 db) install on a 80 metres high tower.
The Mikrotik server is in the cellar.
It is between aerial and Mikrotik server approx. 90 metres of cables.(CNT400)
This is my problem that cable is too long and the signal gets too weak.
How can I solve this?
http://www.x-dsl-online.de/htm/images/MT.jpg Hello to everyone. I have a question on the passing on of PUBLIC IP. I have 6 IP at the disposal. My MT server gets one. I would like to pass the other 5 to my customers. However, I would not like to use a NAT. If I dial in at my provider and check my IP...
I need a script, that I can change a system user name every month.
The new system user must have the same password.
It's possible?
So all system user need the new login every month.
Sorry for my bad english
Hello, I would like to build up a transmitting terminal. I would like 4 sector aerials (90°) with two to operate mikrotik router. It is my consideration that I use different frequencies with the same SSID. Is this recommendable? I would like to produce a failure safety also. how could I solve this b...
I have big problems with SIP VOIP.
I can't do VOIP over MT with SIP Protocol.
I Masquered my network.
Can anybody help me with the config?
If I use IAX, all work OK.
thank you, I wil do that.
Can I use the MT client with 3 pppoe accout, too?
or does the pppoe account it have to run over each PC?
My english is not the best
PC / / wireless / MT AP )))) ((((( MT client ------------- PC | \ | \ | \ PPPOE Server PC I would like that each PC log in seperatly over pppoe. So each PC have a each pppoe account. It's possible? thanks you
I have a wrap Board and I can buy an usb adapter for the wrap Board.
Can MT support a Voip phone, that I connect over usb with the MT??
(USB Voip phone)
It is the problem that MT does not recognize it.
One Session is only if one logged in already not if one wants to log in first.
This has not solved my problem.
I need help urgents
Hello, I have a great problem. I use MT with the version 2.9.10. Everybody dials in with pppoe. Everything runs except for a thing perfectly. I have customers that have a Linksys WRT54G router. This dials in about pppoe. Sometimes this equipment causes problems and tries to build up hundreds of pppo...
HEllo, I have a problem with pppoe client. My clients have linksys router as pppoe client. All works fine. The router connect with MT without problems. Sometimes have the linksys router a problem. It tries to develop several connections within fewer seconds until the limit is reached. Can I limit th...
Hello, I have a new situation. I have 3 DSL lines. 1. 1000/1000 2. 1000/1000 3. 1000/128 Now I have set defaultroute on line 3 and redirect HTTP,POP§,FTP and other services to line 1 and 2. All works fine. My problem now is, If I want connect me with the MT over the Internet with the old IP address ...
Hello, I have a problem with my config. If I configure the MT with one DSL connection (line 1), I can ping this IP (static) from other computer (over Internet) and can connect me with VPN. If I configure my MT with Load balancing all works fine, but I can ping my static ip from line 1.(no connection...
it's possible to limit P2P upload ?
I have a problem with P2P traffic.
I limit P2P traffic.
Clients say, that they have a poor download, but a good upload.
Now I want to limit the upload and download separately.
So clients have more download.
I have a problem with VPN connections.
If Load Ballancing enable (2 lines from differently ISP),
I can't connect with MT from outside.
If Load Ballancing disable, all works fine.
Why??
Hy,
I have a problem with clients, that use X-BOX live.
I use load ballancing (2.9.1)
If I don't use the second line, (no load balling)
the X-BOX connection work fine.
Play the client over both lines (load ballacing), He lost the connection after few minutes.
Can anybody help me??
When the connection are down, I can't ping the Gateway. I can't login with winbox, too. I only see, that the pppoe connection are stable and it sends information but not receive. The DNS can't ping, too. But when all works fine, I can ping always. It's a amusing thing. Now I have reset the MT and re...
DNS Server work fine. PPPOE give the corecct dns. It's amusingly, it functioned months long with this configuration. suddenly went nothing more. If I type "ipconfig /all" (windows) is this the result: IP Address = 190.160.2.100 Subnetmask = 255.255.255.255 Standart Gateway = 190.160.2.100 ...
My Network topology. Eth0 = Internet Interface Eth1 = Internet Interface (Load Balancing) Eth2 = Local Interface (Clients) 190.160.2.xx Eth3 = Radius Eth4 = Debian Server 192.168.1.250 I work with NET (Masquerade) I hope this Infos are OK
I need your help.
I want setup a Samba Server.
My clients need have access on it.
If I connect my computer direct with the Samba Server, all work fine.
If I connect the Samba Server over MT, I can't connct with it.
How I configure MT, so that I can access to the Samba Server over MT.
thank you for your answer.
I know, if you an ISP in Germany, you must log Data.
It's wrong??
I have many clients that use P2P.
Thay walk with my IP address.
Hello, I have set simple queues for all clients with Burst. That work fine. Now I have connect a FTP server with mikrotik. It's possible, when clients download over the FTP server, that the simple queues not match the traffic?? My conf: Ether1 Internet Ether2 Internet (Load Balancing) Ether3 Local (...
thanks. my Problem is, if i want creat a graph with cacti, I have this problem: ../...traffic_in_36.rrd': No such file or directory I want to graph any Client Interface. I have a Radius Server, but I don't think how I can do it with Radius. I would that clients can login and see his Traffic. Can any...
Hello, i have a problem with the PPPOE server. Clients can login, but sometimes they can't download anything. The pppoe connection on the computer show that it sends but receives anything. When clients disconnect an connect again, it can be that the problem any longer does not exist. Can you help me...
Hello, I have a problemwith Bandwith. I wanted to order a Bandwith "2Mbps)upgrade today,because i had still one 1Mbps SDSLConnection. Now i can't make an upgrade, why it is impossible. I can only order a second 1 Mbps line. Can I connect both lines, so I have 2 Mbps??? I hope you can understand...
I notice that when I set an IP address on Ethernet Port, it's OK for one day.
After one day it says me, that is invalid.
After reboot, all is OK again.
Hello, I have found two bugs in RC5. 1. If I go to PPP->Active Connection I can see user who is online, but I can't see RX and TX Rate. If I go to Interface, I have the same problem. After reboot, all works fine. 2. sometimes, when I go to LOG, there is nothing. After reboot MT, I can see log files.
If I reboot the MT, all dtraffic data in simple queues are lost.
It's a bug in 2,9 RC5 or it 's normal??
I want kept the data of simple QUEUES.
Is there a possible??
Is there a solution to reroute al clients (pppoe) to a determined address with first login??
I want to reroute all clients to my homepage
I use MT 2.9 RC5
Hello, I have a problem with P2P. is there a possible to limit P2P connection?? My problem is, if clients starts download P2P, other clients have problem with the download speed. I have magle P2P, works fine. But the problem is the connections to P2P. In Firewall->connections i have too many connect...
I have read the manual, but never canche.
I have made the same setup, but after 1-2 second I have the max. Limit.
Why is it so??
I need the feature urgently!!
Please help me!!
Hello, I had already times written, that I have a problem with the burst time in simple queues. My problem is that I can't limiting clients with burst time. My config: Name - xxx Target Address - 192.168.2.201/32 Limit At - --/-- Max Limit - 262144/524288 Burst Limit - 393216/786432 Burst Threshold ...
What can I do ??
This is not a good idea to set TCP Estabilisced Timeout= 00:01:00, because I have a lot of clients that use ICQ.MSN and other chat programm.
Can I use an other solution??
Hello, I have a problem with the Firewall on MT RC5. I drop all P2P and works fine. If I set the rule with time (01:00 - 06:00) the Firewall don't drop P2P. Can anybody help me?? I want drop P2P from 06:00am to 01:00am. The time between 01:00 - 06:00 P2P allow. I hope you can understand me, my engli...
Hello, I had already times written, that I have a problem with the burst time in simple queues. My problem is that I can't limiting clients with burst time. My config: Name - xxx Target Address - 192.168.2.201/32 Limit At - --/-- Max Limit - 262144/524288 Burst Limit - 393216/786432 Burst Threshold ...
Thank you. in the last day, i have some entries in the log file. i don't know, what this is. The log entries is: - received ISAKMP packet from 81.155.161.43:500,phase1,Identity Protection - peer not configured - received ISAKMP packet from 81.155.161.43:500,phase1,Identity Protection - peer not conf...
I have a problem with an IP address. I have drop all traffic in the "Input Firewall Rule". the only address who not is drop is my VPN connection. This is the log: input->DROP, in DSL, out:(local), src-mac 00:0e:50:3b:xx:xx,prot TCP(syn), 81.169.188.68:50038 -> 62.xxx.xxx.xxx:100 (my addres...
i would like give the clients a download speed of 1024 Kbps.
But after 60 second, MT must limiting the traffic.
I have seen the other post "limiting big files" but that can't solve my problem.
I don't know, what i can still make.
It's a problem, use Burtst Time with pppoe clietns??
Thank you for your answer. Name - xxx Target Address - 192.168.2.201/32 Limit At - --/-- Max Limit - 262144/524288 Burst Limit - 393216/786432 Burst Threshold - 26214/52428 Burst Time - 65/75 My setup looks so now. When i start a download, i can download with 500 - 530 Kbps (25Kpbs pload). after 75 ...
i'm using the client address. I can see the traffic from the client. But it is impossible to limiting the bandwith. My setup: Name - xxx Target Address - 192.168.2.201/32 Limit At - 65536/131072 Max Limit - 262144/524288 Burst Limit - 393216/786432 Burst Threshold - 262144/524288 Burst Time - 10/20 ...
Hello, i have a problem with simple queues. I would like limiting downloads of big files. i used the burst feature in the simple queues and set burst time at 75 second. When i start a download i have full downloadrate. After 75 second i can't see any change. The download continue with full rate. The...
thank you for your answer. It's OK. I would access from Internet, too over VPN. At the moment i can this. But when anyone ping the Router IP over internet, can see the Mikrotik default Page. Can i make it, that only i can access from Internet over VPN. Home ----------------Internet----------------MT...
I have done this. no problem, i can access again. i had written this in the Firewall rle. /ip firewall rule input add connection-state=invalid action=drop \ comment="Drop invalid connections" /ip firewall rule input add connection-state=established \ comment="Allow established connect...
i have resolve the problem with firewall rules.
But now i can't access to MT.
Can I use a trick to log in??
I have permitted only Network with IP 192.168.3.0/24.
I had made a backup before i change the setting.
My last possibility is to install the MT new, if it gives no trick.
Hello, sorry for my english, ist not the best. I have a question about the MT. I have the version 2.8.26. When the clients, which have the ip addresse 192.168.1.xxx, open the Internet explorer and tap the IP from the Router (192.168.0.254) they can see the Mikrotik info page. The same one is over In...