MikroTik

lahoras

When Torch windows is started don't show anything, is necessary press stop for that show information, I saw this since version 3.34, I'm using windows 64 bits version

lahoras

My experience is bad, nat 1:1 do not work, clients conections are very slow.

lahoras

Hello, is not a problem on my mANTBox 12s is native chip limitation¿?

thank again.
ARIEL

lahoras

Hello thanks for red this post: I'm using a mANTBox 15s, and when I try setup of 5 mhz or 10 mhz wide channel on interface list, and in bottom of tab wirelless show this erros: no supported channel scan list does not support channel empty scan list This fail is when I seting on Frecuency Mode, regul...

lahoras

Hello, increment on AP tdma-period-size=6

regards

ARIEL HORAS

lahoras

seems like bug, can any Mikrotik staff confirm this?.

regards

ARIEL HORAS
Systemas MicroInformaticos

lahoras

I have a problem with the new command / disk on Ros 6.20, I am using a RB450G and I find microsd installed, which may be the problem?, anybody can help me?

Ariel Horas
Systemas MicroInformaticos

lahoras

IPANetEngineer; IPANetEngineer; Sorry for reopen an old post, but I need your help, I begining with bgp multihoming configuration, I have two peers and I want use all my block /22 only, no as last example that where route an /24 block for every peer, is possible this?, can you let me an example here...

lahoras

I think R5HSPN is a very good choice, in my case, I had pannel with vertical polarization only, then I just repace old r52 and imediaty my wireless network was converted to MINO one chain, the only problems was that in rb433 does not possible install 3 units, to install two units due invest heatsink...

lahoras

Hello, i need save log data and graphics on microsd, becouse When power is down is lost this data, can enybiody help me whit this or is not possible?.

thanks in advance,

ARIEL HORAS
Systemas MicroInformaticos
Tunuyan-Mendoza-ARGENTINA

lahoras

I'm using RB411, 411AH, 433, 433AH, RB600, RB600A, RB435G, in all board PMT system are not works, specially were I have to many direfrents CPE's brand, on some only there are UBNT CPE, but before 3 o 4 hours, customers links down, I have back to 5.14, really I had a black monday when I was upgraded ...

lahoras

Did you read my post?, I know that give this error, but if you try using winbox is possible change frecuency processor, You dont need use serial console, try on winbox system routerboard and changue processor frecuency, is possible until 1333 mhz. It's clear that you're not test my solution, then re...

lahoras

Thanks, for explanation, but I'm using only chain 1 and chain 0 is deactivated on HT options, I decide use chain 1, because when scan signals are much beeter than using chain 0, minipci board is a Mikrotik R2N, and this is possible set up with compex MIMO models too.

ARIEL

lahoras

eugenevdm,i'm trying use firewall on bridge to block passthrough between wlans of my RB433, my case is similar because I want that windows customers can not access to other users that by default accidentaly have same group name and have any resource shared. It was imposible for me makes that works, ...

lahoras

You dont need use serial console, try on winbox system routerboard and changue processor frecuency, is possible until 1333 mhz.

ARIEL

lahoras

I m actually using only 1 antenna but on chain 1 have best perfomance, that using chain 0, can you help me explaning reason you have to recommend chain 0.

best regards.

ARIEL

lahoras

Then the problem dosen't memory storage?, how many metarouters can run simultaneously on rb1100AH?, can you help me with this?, I have purchased a RB1100AHx2 and is not support metarouter, is incredible perfomance with respect RB1100.

regards

ARIEL

lahoras

Is very inportant this question, becouse at the moment, as metarouter only run on rb1000 or rb1100 and this are discuontinued, in new line rb1100ah and rb1100ahx2 dosen't run, only is possible use on rb450g and is not very realiable, too many users can confusind and try virtualization on KVM, belivi...

lahoras

Normis, all your answers are clear, it is true, you have edited all the datasheets, none now says which is the size of the NAND, anyway, you should definitely relive special subject have degraded the product, I always had full confidence in the Mikrotik company and this action is disappointing.

ARIEL

lahoras

Mikrotik has made a mistake, or is it possible that the MANUFACTURER, how annoying this situation is, do not show their faces and recognize the error giving explanations, is easy say 'RB1100AHx2 metarouter does not support', I believe that if they had published it on datasheet, had not sold even a...

lahoras

Normis: Industrial tractors do different things that street cars as you say, in this case RB1100, RB1000AH & RB1000AHx2 are routers, and theoretically a router with a processor that can run more fast, is the evolution of the initial product, but with minus memory resource?, that not permit do sa...

lahoras

AHx2 is multicore, but Metarouter does not work on multicore systems.

Ok, if is not work why error reported when I try add metarouter is "not enough resources (6)", this only makes confusions and waste time, this is not clear explanation.

ARIEL

lahoras

Normis, sorry, when I wrote the post I made the mistake of referring to as RAM, when realy is NAND, on RB1100 is 520,1 MB and in RB1100AHx2 is only 41,7 MB (is almost 10% from RB1100 and RB1100AHx2), I Would like if you can, read all post and tell me finaly why is not support metarouter RB1100AHx2, ...

lahoras

update to newest version possible, downgrade to previous version and upgrade back to newest one. in this case 5.14 then downgrade to 5.13 or 5.12 where problem is resolved and then back to 5.14 Unfortunately in older versions this board could load smp kernel in some rare cases and stick with it. ne...

lahoras

RB1100 works fine but is discontinued, virtualization is the future, in my old system I had 3 rb450 2 rb450G, 1 rb750G and 1 PC. thanks to rb1100 and metarouter could reduce number of equipment and have fewer points of failure, and improve the quality and availability of my service. I don't understa...

lahoras

Normis, sorry I can understand how I can use MicroSD to another router, I have running virtual router running on doing load balance on RB1100, this is not possible on my new RB1100AHx2, can you help me to implement it, the problem is ram.

thanks

ARIEL

lahoras

AND I have other question, on first RB1100 have 512 mb ram too, this is very important, I can understand how is possible reduce memory on this great router, is realy crazy, I can run metarouter..........realy apologize.

ARIEL

lahoras

Normis...your answer is correct, if routerboar shows all frecuencies mini-pci works on them?, becose I test to many boards that list ferecuency but only works fin on 2,4 ghz range, for this is my post, can you help me or tell me where is spec of r52HN?.

thanks in advance.

ARIEL

lahoras

I haven´t installed yet R52nH on routerboard, my question is becouse only I have R2N, but this was discontinued and I need have a replace if R2N dosen't work more, whith the same features. There are to many branch radios that in theory suports this frecuency range but they aren't has good perfomance...

lahoras

Actually I have varios R2N mini pci radios on production, but they are discontinued, this wokrs fine, really, frecuency range's R2N is 2.192 - 2.539GHz (5 MHz step) on 2,4 ghz, my question is, R52hN support the same range's frecuency on 24, ghz?, and which is on 5 ghz?, I can found this information ...

lahoras

The problem is becouse is not posible, your CPE me be transparent only one mac, or pppoe server seems cpe mac address, only will be possible if you can implement wds on CPE and obviously AP system, whit this you can conect multiple customers over ethernet cable pluged on same CPE.

ARIEL

lahoras

On changelog says,

*) fixed problem - remote web interface didn't work well over VLANs;

But if I want conect to web interface from trunk port isn't posible, is this a bug? or simply sw205G do not do this.

thanks in advance

ARIEL

lahoras

Note! The recently released RouterOS v4.7 contained an uncommon DHCP server problem in some non standard installations, until a fix can be provided, you can use RouterOS v4. Can tell me wich is UNCOMON DHCP SERVER I m using dhcp over x86 and have not any problem, is posible to know more clear the pr...

lahoras

Hello, recent was in mikrotik web site a new v4.7, and now is not present, have any bug?, I'm runing it on rb433 and x86 and does not have any problem, can you explain me if there are some problem with v 4,7 must I dowmgrade?

ARIEL

lahoras

On recent rosV4.7 version the problem is the same.

ARIEL

lahoras

This is better joke that I have suffered, but works well,

, don't try logic, main is not A antenna!!!!, main may be B or AUX.

thanks Jsuter, you avoided me the madness!

ARIEL

lahoras

Nobody can tell me anything about this?, can you help me.

greeting
ARIEL

lahoras

Hello, I'm trying use wiki's example, /ip firewall mangle add chain=forward tos=xxx action=mark-packet new-packet-mark=VOIP passthrough=no \ comment="voip tos xxx" disabled=no Where in my case TOS is 184 (mark of linksys voip adapter sp2102), then add queue tree / queue tree add name="...

lahoras

Normis, I understand your reply, but in web-proxy is possible set up another hard unit and reserve ram memory, this options are not present on ip-proxy, and I can found on manual how to, can you help me?, thanks in advance.

ARIEL

lahoras

This is another compac solution, http://www.tibbo.com/products/, it was help me too much, becouse is a transparent rs-232 over ethernet link, i hope help you....

ARIEL

lahoras

I'm discovered that is not possible change IRQ on async port.

thanks in advance.

ARIEL

lahoras

Hi, Mikrotik OS support two serial ports, COM1/3F8 on IRQ4 and COM2/2F8 on IRQ3, I've added an ISA modem jumpered on COM3/3E8 on IRQ5 and is not detected, is a ROS limitation becouse I can fond on manual how I can change or add another serial port.

thanks in advance,

ARIEL

lahoras

Yes, TCP/IP never well dead, in a way or of the other, we will continue transmitting packets!!!
I send a mail.

thanks again.
ARIEL

lahoras

Maxi, thank you very much, my name is ARIEL, my amateur radio license is LU7MBE, I remember you since packet radio, very cool times!

thanks again

ARIEL

lahoras

Hello, and thanks for help me, I have running mikrotik OS on PC over compact flash and I want install a hard disk drive to be used by web proxy, must I install a drive and reinstall router OS again or simply install hard dirve and start system?.

thanks in advance.

ARIEL

lahoras

sergejs, thank you for feedback, the problem is only if I implement pppOe client, but only with echolink aplication, with emule for example that requier one tcp an udp port wroks fine. Actualy I have a ADSL line from my ISP, and they give a modem/router zyzel that can operate on bridge mode or routi...

lahoras

sergejs, I can't specify address on public interface becouse is a dynamic, however I test it but dosen't work, I can understand why not run ok. can you check if your suggest rules may be this?. 5 chain=dstnat in-interface=ether2 protocol=tcp dst-port=5200 action=dst-nat to-addresses=192.168.0.2 to-p...

lahoras

Well, you may use specific port application that is destined to public (PPPoE client) interface. Hello, thanks for feedback, this are my nat rules 3 chain=dstnat dst-address=172.18.1.2 protocol=tcp dst-port=5200 action=dst-nat to-addresses=192.168.0.2 to-ports=5200 4 chain=dstnat dst-address=172.18...

lahoras

Documentation describes it, it is not very hard option, 'ip firewall nat add action=dstnat chain=dst-nat dst-address=public_address_of_the_router dst-port=5060 protocol=tcp to-addresses=10.0.0.50', the same rule for UDP. Hello, I'm trying do this to works with echolink software, but dosen't work, I...

Search found 49 matches