Still problem. [admin@coel_wireless] /interface ethernet> print detail Flags: X - disabled, R - running, S - slave 0 R name="ether1_lan_dynamic" mtu=1500 l2mtu=1600 mac-address=00:24:1D:B4:65:7D arp=enabled disable-running-check=yes auto-negotiation=yes full-duplex=yes cable-settings=defau...

No problem, but you have to wait till tomorrow. My emplyes borrow my last RS cable.

I think there is a way to install it by RS232. I used it in the RB133 same way damaged. Plug your RS232, download terraterm, follow mt menu and the white rabbit.

RouterOS 5.0 beta 2 installed. All three NICs are working. [admin@MikroTik] /system resource pci> print detail 0 device="03:01.0" name="DGE-528T Gigabit Ethernet Adapter (rev: 16)" vendor="D-Link System Inc" category="Ethernet controller" vendor-id="0x118...

This is my HOTSPOT - free for all (2h per day). (we set about 20 hotspots on Konin city area)

Hello. Is there any custom driver or whatever needed to run RTL8111C card? What I found in resources: 1 device="02:00.0" name="unknown device (rev: 192)" vendor="Attansic Technology Corp." category="Ethernet controller" vendor-id="0x1969" device-id=&...

Oh, I need to precise my problem... I have a computer connected to bridge and using address from A class. All traffic from this specific computer must be somehow forwarded to hotspot interface. User of this computer must see a login page on his screen. Of coz I know MAC and IP addresses of this spec...

Hey guys. I have a little problem and need your help. This is my installation. http://www.coel.pl/kuba/hotspot_diagram.png I need to forward traffic of one specific IP from 10.0.0.0 subnet to hotspot subnet/interface. I can't just switch cables, it must be done by MT firewall. Is it possible? I was ...

I had the same issue.

At my network problem solved... One of Mikrotik's had PROXY-ARP on ether2 and when host trying to get IP from DHCP (static leases in my case) he thinks that this specific IP is already used.

DISABLE PROXY-ARP on every MT.

I had the same issue.

At my network problem solved... One of Mikrotik's had PROXY-ARP on ether2 and when host trying to get IP from DHCP (static leases in my case) he thinks that this specific IP is already used.

DISABLE PROXY-ARP on every MT.

I had the same issue.

At my network problem solved... One of Mikrotik's had PROXY-ARP on ether2 and when host trying to get IP from DHCP (static leases in my case) he thinks that this specific IP is already used.

DISABLE PROXY-ARP on every MT.

I had the same issue.

At my network problem solved... One of Mikrotik's had PROXY-ARP on ether2 and when host trying to get IP from DHCP (static leases in my case) he thinks that this specific IP is already used.

DISABLE PROXY-ARP on every MT.

Hello guys. I have a strange problem with one ALIX. Every couple days the ethernet is starting to generate high latency like 110-120ms (every packet same big latency). Latency is the same, even without any big traffic. When I reboot this board all goes back to normal and it's working fine couple nex...

Best wishes guys for all the Mikrotik stuff!!

Hello guys. I have a little problem with Dude and ping probe. My network is big and little strange, but in most cases we are using static routing (forwarding) and AP and STATION modes. Pings between devices are good, but almost every first ping is much bigger than the rest. For example: http://coel....

OK, thanks

The best what i got was 34mbit UDP and 24mbit TCP... I need to achieve 10/10mbit TCP without any losses. In nstreme this is working well.

EOIP + nstreme + polling

In near future I will try one RB600 and P4 2.8 on the other side.

polling turned ON ok, still testing... 20MHz channel, freq 5680, signal -57/-59 @ 36mbit, no framer policy, no nstreme --- BT showing 15mbit TCP halfduplex 20MHz channel, freq 5680, signal -57/-59 @ 36mbit, framer policy DYNAMIC 4000, nstreme enabled --- BT showing 28mbit TCP halfduplex 15 mbit with...

already tried nstreme... jitter is too big.. ping are random - min 0.8 max 50ms, avg 3ms

status: connected-to-ess band: 5ghz frequency: 5680MHz tx-rate: 48Mbps rx-rate: 48Mbps ssid: "bridge" bssid: 00:0C:42:1B:24:1D radio-name: "000C421B241D" signal-strength: -62dBm noise-floor: -102dBm signal-to-noise: 40dB tx-ccq: 94% p-throughput: 29816 current-ack-timeout: 92 cu...

Hello.

All firewalls disabled, modules R52H.
532A R5, freq 5680, chan 20MHz, WDS withour framing and nstreme = 15mbit HDX and 8/6 FDX
same bridge with NSTREME AND FRAMING = 36mbit HDX and 17/17FDX

ROS 3.0RC13

Any ideas how to fix that low transfer?

Hello. It takes days to achieve that quality. root@***********:~# ping 77.242.***.*** -i 0.001 PING 77.242.***.*** (77.242.***.***) 56(84) bytes of data. 64 bytes from 77.242.***.***: icmp_seq=1795 ttl=64 time=0.848 ms --- 77.242.230.20 ping statistics --- 1795 packets transmitted, 1795 received, 0%...

Hello. Gluegun rulez the world!

My version of ufl with glue.