I just trying to forward multicast traffic from ether7-iptv to ether3-local using igmp-proxy. 192.168.89.88 = multicast source 192.168.89.89 = ip at ether7-iptv 224.2.2.2 = udp multicast streaming [admin@core] > tool torch ether7-iptv src-address=192.168.89.0/24 dst-address=224.0.0.0/4 ip-protocol=u...

Solved.
Thanks anyway

We try to advertise our Public IP via ASN to 2 ISP (A & B). Currently running ROS6.11 on x86. Our network: 10.1.1.0/22 Instance all OK (redistribute to another BGP enable). Peer all OK. /ip bgp network: 10.1.1.0/22; 10.1.1.0/23; 10.1.1.0/24; 10.1.2.0/24; 10.1.3.0/23; 10.1.3.0/24; 10.1.4.0/24 all...

anyone got same problem?

Dear all, Today i try to create pptpd using rb750. I'm using 10.3.7.1 as router ip and 192.168.10.1 as pptp-local-ip. remote ip set by pool. On remote area im using win7 as pptp client. Problem are when pptp connected and I try to ping 192.168.10.1, latency raised. Totaly different when I try to pin...

Depends on your configuration. For just routing without any QoS or firewall rules the data sheet contains the official test data, it's available on routerboard.com. Any QoS rule or firewall rule means that the router spends time not routing, affecting throughput performance.

Thanks again fewi

It's a huge difference. Generating packets is a lot more work than routing packets, and in normal operations only a tiny fraction of all traffic is generated by or terminated on the router so your test doesn't at all simulate real world traffic conditions. Use two PCs with the router in the middle....

Did you push those packets through the router, or did you have the router generate or directly receive the packets used for the bandwidth test? There's a huge performance difference between the two.

rb1000u act as bw-test server and the other as bw-test client. how big the different is?

I just wanna now how many real tcp/ip throughput RB1000U can handle only on routing.
I just tried using mikrotik bw-test its can handle only about 17mbps up and 97mbps down with 100% cpu resources. We had a STM1 connection, should we using a PC or thereis any other way?
Thanks.

dear all,
I just wanna know how to do reset rb450 ros back to default cause I forget the password.
I just see the scheme but do not know exactly which one are ROS Reset on board...
And how to do that? just like RB433 or any other way? thanks.

Rgds.

dear all, I wanna know if that possible to using 1 login and password for multiple user (about 30 users at same time) using mikrotik hotspot or usermanager? I just want my clients to read my banner everytime they start using my internet connection,just every their start using it no else, so I refer ...

dear all, I got problem with routing. heres my network configuration public (public ip) --- (eth0)MT(eth1)(public and local IP) ---(public and local IP)local on local I have several clients, so some of them using private ip and other using public one. oke lets it be like this ; On MT : 192.168.1.1/2...

Dear all, Before iI`m using bullet2 as my AP, then cause i got more users I trying to upgrade my AP to rb433 using 2xar5212 mpci, 1xcm9-gp. But after configuring my AP all of my cient that before never got problem, got to many problem, from too high ping latency and on some sites they can do ping, b...

Hi all, I got some problem here, scenario be like this : I have several internet connection, eth0 = national connection eth1 = overseas connection eth2 = vsat connection for cheaper download eth3 = clients i just separate national and overseas connection, its not a big problem. Problem was, I want m...

I just bought new RB133 with XR2 with Router 2.9.38 installed on it. I using this RB as AP-Bridge. Problem is when its active cometimes my clients can connect to the AP but after several hours or minutes clients got disconnected and can`t read AP SSID at all, so i must do hard reset to my AP. Then i...