Trying to install ROS for the PPC on a CF card using a card reader on a Windows PC... When I first open Netinstall I can see ALL the ROS versions (including mipsbe, ppc, x86 etc) in the directory. When I click on the Drive Letter in "Routers/Drives" at the top of netinstall it immediately ...

If it's got a daughter card on it remove the daughter card and put the mini PCI cards right on the RB600. We have a dozen RB600's, previously had problems with the ones that had daughter boards and 4 cards installed, removed the daughter boards at Uldis's suggestion and no more problems.

S

I have an RB 600 with the same problem - it randomly reboots. The log reports that the board was rebooted by the watchdog timer but the timer is not enabled. It has an RB 604 daughterboard with two SR5's, one SR2 and an R52H installed. No cards installed in the RB600 itself. Now running 3.13 and sti...

On 3.7 Is it possible to influence the RIP Costs (Metric) on a per interface basis ? In other words can I advertise the same route out various interfaces with different costs ? So, for example the cost of routes advertised out Ethernet0 is +1 and Ethernet1 is +3 and Wireless0 is +4. I know some othe...

Had this problem. Using even the newest CPQ firmware doesn't resolve the issue - fixed it by moving to only TKIP on the AP, and set the AP rekey to 3600 seconds (Tranzeo default). Also hardcoded the AP and the Tranzeo's to B mode. Of the 30 or so Tranzeos that still haven't been replaced across the ...

Is it possible to set up Graphing of Rx/Tx CCQ ?

I cannot find the Mib entry for either value to create the probe.

Thx,
S

This same RB333 has a SR2 on a 15 db VPol omni. Last night I installed two test clients on the SR2. #One is a RB411 with Compex WLM54G in a 15 db Rootenna. Range is about 190 meters to the Omni antenna - it's about 110m from the base of the Tower, so it's basically aiming straight Up. #Two is a WRAP...

Spent 3 hours working on this link today. The RX/TX CCQ is 90%/75% and it still dropping packets. I don't think this is a link problem. It goes for hours at the same CCQ with 2Mbps load in both directions with no issue, then randomly drops packets. The CCQ remains pretty much the same the whole time...

3.3 AP and 3.3 Client The Client Tx/Rx Rate occasionally displays 48Mbps/11Mbps-SP, or /2Mbps-SP, etc.
What does the SP indicate ?

Thx,
S

This is a new link using a RB333 ROS 3.3 with SR5 Going to a WRAP board with NMP8601 ROS 2.9.27 Tx/Rx Signal is -81/78dBm Rx/Tx CCQ is 69/80 % SNR 23 dB. Seeing about 3% packet loss across the link with almost NO LOAD. The WRAP has another conenection to an SR5 another WRAP ROS 2.9.27 which is simil...

Disable "Secure mode" when using MAC address connection. It's been a problem since 3.x.

I've configured MAC authentication for Wireless Mikrotik CPE's (clients) against FreeRadius with WPA2-PSK/AES for encryption on a MT 2.9 AP. On the MT CPE - Security profiles: Mode = Dynamic Keys Authentication Types = WPA2 PSK Unicast and Group Ciphers are both set for aes ccm WPA2 Pre-Shared Key =...

This would be VERY helpful for installing RB based CPE.

It's some kind of power problem for sure ... Climbed the tower this morning and found this : http://forum.routerboard.com/viewtopic.php?f=3&t=3649

Anyone have any idea as to the cause ?

Thanks.

RB532A 2 X Sr5 PacWireless 48v POE 120' Shielded Ethernet WLAN1 AP-Bridge Transmit power 23 dbm WLAN2 AP-Bridge W/WDS Transmit power 17 dbm Rebooting randomly. Appears to be related to Through-put on WDS the Interface, but I cannot reliably reproduce it. It generates an autosupout file (can anyone r...

Thanks - I replaced the Pac Wireless Adaptor on the top end too - no change. And the flash only happens when the back end cable is plugged into a Switch... a laptop works fine. Very bizaar. I think I'll run another cable up an use it for Ethernet on another port and the POE can stay on it's own line.

Did all that - no difference. Tried a straight through and a roll over cable on the 'hub' side of the POE too - same thing. Also tried multiple switches - no change. Only thing that works is when the 'hub' side of the POE is plugged into a PC or Laptop. As soon as it's connected to a Switch the RB d...

RB/532A With a Pac Wireless POE-48i . We've had two times in the past 4 months when it locked and the POE had to be unplugged/replugged. Worked OK until last night when we had a good Thunder storm. No hits at the site, but now when the POE 'hub' side is plugged into the Switch (tried three different...

Same Problem on a WRAP 2C, in Station mode, regardless of the 8602 I try to use (have tried three now). Seems to be related to upload (sending data towards the AP) more than anything. If upload utilization is more than >256 kbps it reboots, and keeps rebooting for a period of time (10 to 20 minutes)...

LOL - so right after posting I realized the script was looking for the 0.0.0.0, not the 0.0.0.0/0 route .... works now

I'm sure this is easy, but I'm at a loss... Trying to configure netwatch to change default route when ping to a specific IP fails. I thought this would be the correct command but apparently not /ip route set [/ip route find dst 0.0.0.0] gateway 172.16.0.2 And the MT returns numbers: It is looking fo...

Nobody ?

Here's the problem: Switched the DSL SpeedStream 5200 modem from Router (PPPOE client) to Bridge mode. Configured a PPPOE client on the MT, but it doesn't connect. Packet sniff shows the PADI PPPOE Server Discovery outbound, and a PADO reply from the ISP's PPPOE server, but the MT just sends another...

From what I understand PCQ would classify based on individual ips depending on how you calssified the flows under /queue type (e.g. SRC IP, DST IP etc)... but what did you find ??

Thanks Craig... but I found an entry in the archives that indicates it was to be included in 2.9 Beta 8 for non-Routerboards.
http://forum.mikrotik.com/viewtopic.php ... ght=usb+up

So I *think* it supposed to work ?

Trying to add a APC USB UPS to MT. The USB ports sees the APC UPS, but how do you add the USB port to the system so that it is available to the UPS>port menu? Thanks S. [admin@MikroTik] system resource usb> print # DEVICE VENDOR NAME SPEED 0 1:1 USB UHCI Root Hub 12 Mbps 1 1:2 American Power Conve.....

Very wierd... it recognizes _any_ two EtherPro NICs . But not more than that of that same type. I installed another type of card (3Com) and viola shows up. Tried different slots etc with the Ether pro - no change. Maybe it's the BIOS ? It's a Dell Optiplex GX110. Oh well time to get some 3 Com cards...

We have a boatload of these NICs, and I've tried several in the MT. They seem to be good in other systems... Fedora3, XP etc. I thought that we originally built this box with only 2 interfaces and added a third after the fact, but really not sure now, could be that we added the other card before we ...

Thanks. The cards are all the same type. Intel Ether Pro cards. Which appear to be on the supported list... Compatibility shows: Intel i82557/i82558/i82559ER/i82801BA-7 EtherExpressPro PCI cards Installed NICs are all: 721383-008 Intel® PRO/100+ PCI (TP) PILA8460 **82558**, Full Duplex, 3 LEDs, No M...

We originally installed with 3 Network Interface cards in the MicroTik PC. Now we've installed 2 more interfaces but they don't show up. I assume this is because there's no Kudzoo type process to pickup on hardware changes. Is there something that can be done to force the detection of the new NICs ?...