are you planning good-looking indoor case for mAP? Something like Unifi o Ruckus? mAP is already in an indoor case. I can not imagine this case in the lobby of the Sheraton Hotel. Some places need a prettier case and that is why I refer a ruckus or unifi. See this, http://www.rfelements.com/en/prod...

are you planning good-looking indoor case for mAP? Something like Unifi o Ruckus?

Could you please clarify, isn't this basically the same as sending a "auto.rsc" file to the device with FTP ?

Yes but, TR-069 it's a standard already used by us

do u've the config for this, i can't make it work

Hi normis, can you respond this post, please

http://forum.mikrotik.com/viewtopic.php?f=3&t=59565


Thanks

I'm thinking if you can add a simple PIN on LED connections, this will be usefull for turn on / off some kind off things, like FAN, other RB, Lights.

With this simple circuit we can do a lot off things

i'm using RB450G and RB493G

yes, i'm using RB450

I'm trying to do this



/port set 0 dtr=on
/port set 0 dtr=off

but i can't see output voltage on this pin (4), why?

I'm trying to do this



/port set 0 dtr=on
/port set 0 dtr=off

but i can't see output voltage on this pin (4), why?

if i connect a LED on pin 4(DTS) and pin 5 (GND). how can i make turn on?

Hi, im wondering if is there any way to use the serial port to control an electronic board to turn on or turn off other thing. The idea is use the out pin (TXD, DTR and CTS) to control. I need a high state (bit 1) on those pin and them i'll take the signal to control some thing. Today i'm using LED ...

Great, i'm using local isolation and it works. I put the vlan into the bridge and work without problem

now i try this but doesn't work. Iexplorer shows http://192.168.2.1/login?......... but i cant see the login page. I use Unifi AP and Ruckus AP, vlan 23 on WLAN. Note: The AP get IP address from eth5 pool (30.30.30.x) /ip address 0 address=10.10.10.1/24 network=10.10.10.0 broadcast=10.10.10.255 inte...

Hi, im trying to set a hotspot to be used with ruckus AP. This is my config. RB450G eth2, 3, 4, and 5 on a bridge interface (bridge1). || IP adress 20.20.20.1/24 Vlan1 (tag=22) over Bridge1 || IP Address 10.10.10.1/24 eth1 dhcp client and masquerade hotspot over Vlan1 now ruckus AP has 2 WLAN (SSID)...

max rate 300mpbs? or 150mpbs on NM5?

add next hop or gateways on all router to reach your network

something like 192.168.5.0/24 GW 192.168.4.100 on R2

ckeck this value if-snr, maybe is empty

and what exactly do you see with those rules enabled?

whet if you disable just input or output rules, but not together?

If this rules are enabled. Webproxy doesn't work and i don't see connections on webproxy tab

use 1 masquerade without out-interface. This solve the problem

i've the same problem. This works only if i disable this rules add chain=input in-interface=pppoe-out1 action=mark-connection new-connection-mark=wan1_conn add chain=input in-interface=pppoe-out2 action=mark-connection new-connection-mark=wan2_conn add chain=output connection-mark=wan1_conn action=m...

Work without first mangle rules (input - output)

why?

I try many times and this is the only way that i foung to make it work 2 WAN lines 1. Fixed IP 190.12.114.42 2. ADSL (pppoe-out1) If i use masquerade with out-interface, users can't access from wan to my webserver and mailserver. If i don't set !80 on mangle, the proxy doesn't work. Please is this c...