Port forward on the ADSL router and insert a route on it pointing 192.168.3.0/24 via 192.168.2.6. You may need to make some mangle rules that mark inbound connections and on the reverse path apply routing marks to force traffic back out that gateway if your default route on the RB433 isn't via 192....
Good evening, I would explain to me how I do to open the correct ports to a PC or failing that, properly activate UPnP. Right now I have these IP addresses: ((AP)) - RB433: ADSL Gateway 1: 192.168.1.1 (UPnP Off) ADSL 2 Gateway: 192.168.2.1 (UPnP Enabled) eth0: 192.168.1.15 eth1: 192.168.2.6 wlan1: 1...
Thanks for the answer, but i need just inverse of this. I have 2 ADSL providers by ethernet, and i want to route all packets from wlan1 to ADSL 1, and all packets from wlan2 to ADSL 2: ADSL 1(192.168.1.1)-----------SWITCH-----(ETH)(192.168.1.15) RB433 (WLAN1)(192.168.3.15) )))))))) CLIENTS TO ADSL 1...
Good afternoon. Let me explain a little what I have and what I want. Currently, I have 2 ADSL providers with the following information: - Provider 1: 192.168.1.1 - Provider 2: 192.168.2.1 Both routers are connected by ethernet cable into a 5 ports Switch, and this, the ethernet cable of Routerboard....
Good afternoon. I have a RB411U and R52Nm mikrotik card, which I have said it needs 2 antennas equal, a vertical polarization and another horizontal. My question is, Is it possible to use a single antenna, or the worst Cases 2 antennas but not equal?. If so, how would you configure on RouterOS 5.0rc...
Good night. I have a little problem. I bought one which came with Lobo912 a RB411U, firmware 3.30 and a wifi module CM9 100mW. Well, with this configuration, network scanning was available to me, and was about 70. Yesterday I decided to upgrade the board to firm 4.17, so I recognize the R52NM card a...
Good night. I have a little problem. I bought one which came with Lobo912 a RB411U, firmware 3.30 and a wifi module CM9 100mW. Well, with this configuration, network scanning was available to me, and was about 70. Yesterday I decided to upgrade the board to firm 4.17, so I recognize the R52NM card a...
Buenas noches Martín. Ya he conseguido instalar la tarjeta R52N-m actualizando el ROS desde la version 3.30 a la 4.17, siguiendo los pasos que me han indicado en otro post: http://wiki.mikrotik.com/wiki/Manual:Upgrading_RouterOS#License_issues Muchas gracias. Te conozco del foro de 34Telecom, que yo...
This is the data of screen: RouterBOOT booter 2.20 RouterBoard 411U CPU frequency: 300MHz Memory size: 32 MB Press any key within 2 seconds to enter setup.. kernetl not found trying bootp protocol...........................................................................................................
Thanks for your answer. I have a problem with my board. Before you say me this, i was write in console: "/system routerboard upgrade", and now, my RB411U doesn't boot. Please, see my other post:
Help me. I have a big problem for me. I was type in terminal of my routerboard 3.30 "/system routerboard upgrade", and now, my RB411U doesn't turn up. The led on RJ45 PoE conector, blinks in green, and LD501, 502,503,504 and 505, doesn't light, and don't beep after 5-10 seconds. That could...
Hi for all. I have a lobometrics 912, that comes with a RB411U and a Wilstron CM9 for Wireless Module (a/b/g). I was buy an R52N-m for replace a existing CM9, i was install it, but RouterBoard doesn't show any wireless interface. I have to install something driver? How can install the wireless modul...
Hi. How can i change the wireless module on a lobometrics 912 with RB411U, that incorporates a wireless module with 100mW and one radio. I was buy an a MikroTik MiniPCI wireless card (R52N-m) with 360mW power output and two radios with a/b/g/n support. What are the steps I have to follow to open the...