when I tried to install 6.49.10 on my esxi, it is always kernel panic,
but 7.11.2 Stable is good. I tried install from iso/ova/vmdk.

please help I want to run ros6 on esxi. thanks

after setup routing policy like this: /ip firewall address-list add address=8.8.8.8 comment="" disabled=no list=VPN add all addresses should be routed to VPN, and a static route to 192.168.88.2 when routing mark is VPN,all traffic marked VPN is to VPN, will test by adding 192.168.89.1/24 a...

i have a RB450G+E3000, setup openvpn client on E3000, any DHCP client under E3000 will be routed to VPN. It works well for now. but when I tried to separate E3000's IP range from current main intranet, all DHCP client can not be routed to VPN. RB450G port1--->ADSL; port2(192.168.88.1) --->Netgear GS...

rb493g has 2 switch chips, so I guess you have to divide them into 2 groups.

That`s right, it has two switch chips, but how to make rb493g act like a simple 8 port switch, one group of 8 switched ports, without bridging?

I doubt you can do that.have you sent email to support?

rb493g has 2 switch chips, so I guess you have to divide them into 2 groups.

snmp can not see traffic which is not passed through CPU, since they are switched.

I have an RB433 and a 493 that both perform uselessly after upgrade to 5.4 - 100% CPU and essentially no operation - with winbox all devices appear to be absent - wireless will accept a connection on the 433 but then drops it. Basic ip routing appears to be working but very poor and laggardly. Any ...

So where's the 5.3?

send email to support.

Is there a non described change in ROS from version 4.11 on ethernet for RB450G? We have the same problem on a lot of RB thist type. Link look good but with some errors described as rx-drops. Solution is downgrade to 4.10. Please Mikrotik if it is possible repair this problem. This problem is in 5....

hi there
how to graph slave ports on RB450G? currently I see all slave ports traffic are zero.

thanks

Hi MT
Is there a way for us to get rc/beta version of ROS to test it?

thanks

once you set port to slave mode, then you can not see port's traffic. is that right?

would you please tell me which case your 435G is in? or just outdoor case? I am looking for good indoor case for 435G.
thanks.
show anything to you?

i am experiencing this problem too, when can it get fixed?
thanks

demo2.mt.lv is on 5.2, if anyone wants to play with.at least from winbox, I know it is 5.2

I had this problem (same hardware) when testing v5.x and going forth & back to v4.17. ssh service was declared invalid. One difference with you, IP range for clients wasn't limited for ssh. When rebooting with v4, I notice some message one console about ssh server keys being generated... each b...

Hi all
Is it safe to downgrade any older version than 5.1? just because newer boot loader was upgraded with 5.1.

thanks

@adi55,sorry about misunderstood your question,
@willy.sorry too,

I have a big problem. I own a RB450G and yesterday I made a firmware upgrade from 2.28 to 2.29 routerboard: yes model: "450G" serial-number: "2796017D3BA0" current-firmware: "2.29" upgrade-firmware: "2.29" For now the speedtest.net tests decreased dramaticall...

Hi yesterday I found I can not enable ssh on RB450G which was good before.Ticket#2011041766000013 was sent to MT. thanks for help!! [admin@MikroTik] > ip service print Flags: X - disabled, I - invalid # NAME PORT ADDRESS CERTIFICATE 0 X telnet 23 0.0.0.0/0 1 ftp 21 192.168.88.0/24 2 www 80 192.168.8...

I'm trying to use RouterOS 5.1 and I enabled UPnP, but the "Mikrotik Router" don't appears in the "Network" of windows seven. (but utorrent dynamic nat entry appears). All other my UPnP devices (OpenWRT router, WDTVLIVE) appears in my "Network" normaly. When I used ver...

webfig continues loading on firefox4@win7 SP1

would you MT guys test more before release to public?

thanks

Hi, I have RB800 with 2 CM9 cards. I want to connect it to TP-LINK router WR340G using one CM9 card to have access to internet, and to use other CM9 card to work as AP. I have DHCP server running on wlan1 and DHCP client running on wlan2. I have set up bridge (wlan1, wlan2) but when I connect to RB...

Yes you can
/system package uninstall <package-name>

and reboot the router.

thanks for your quick response!!

hi, I am pretty new to routerboard , I am just wondering can I just uninstall packages which are disabled in my RB450G? such as wireless which RB450G will never use? [admin@MikroTik] > system package print Flags: X - disabled # NAME VERSION SCHEDULED 0 system 5.0 1 X wireless 5.0 2 routerboard 5.0 3...

Unfortunately, when I change the Linux router (Sun Netra T1 + Auror Linux - based on Fedora) with new RB450G, I see that effective loading of internet link decreases to 14-15 mbit and found packet loss on WAN interface about 20-30%. The config of RB450G is very simple - only 3 ip addresses assigned...

how did you mount rb411 on that metal board?

when Groove, Omnitik will be available in China? thanks.