thank you very muchI is true. 3 green capacitors are dead
1- noCan you change R1 and R2 Configuration ?
can you add route into device ?
thank you very much .Simple: no way.
-Chris
thank you very much .Hey, in Winbox you normally have tooltips on hover. Have you tried holding your mouse over that column?
racial balance
https://www.balticnetworks.com/rb921uag ... mw-us.html
I don't know from where you got the information about max tx power of 2000mW , the specifications I linked in previous post mention 31 dBm (1259mW) as max Tx power at 6Mbps rate.
mipsle is the name of the architecture, or the name of the CPU family
you can only use packages that are made for the specific CPU. mipsle is for your device.
what is this ??!!My network setup is as follows:
ISP <wireless> RB411 <cable> RB912 <wireless> SXT 5 <cable> RB912 <wireless> SXT Lite 5 <cable> TP Link Router (PPPoE)
OK....done@laithmikrotik please send supout.rif form your router to support@mikrotik.com
FAILEDTry thisCode: Select all/interface wireless access-list add interface=wlan1 mac-address=00:23:4D:76:8F:F5 add interface=wlan1 mac-address=00:23:4D:76:8F:F5 time=8h-20h,sun,mon,tue,wed,thu,fri,sat \ vlan-mode=no-tag
all i want is the help .No more, no less"all I want is you to do everything for me". This is not how the things can work in real life.
/interface wireless access-list
add authentication=no forwarding=no interface=wlan1 mac-address=\
B4:74:43:53:28:B7 time=20h33m39s-20h36m,sun,mon,tue,wed,thu,fri,sat
do you mean you want to make your device acts as an extender?Hi,
can i connect it to some WiFi network, configure NAT and give Wifi to my computers?
thank you.
I found the problem , the mANTBox was in Bridge Mode, I switched to AP Bridge and both clients are connected now.
you dont need to use two omini antenna .using one omini antenna with high power access point (1000mw) is very enough1-what is the maximum distance range if i use two omni directional anntena?
both are usefull depends upon the clients2-which frequency (2.4 or 5) can be used?
be sure of wireless settings of your sxt .But my second SXT lite 5 which is on another area in the city don't want to connect to the same MantBox19s. It's reconnecting all the time.
that depends on the wireless point to point strength and efficiencywhat throughput will I be able to get and is possible to get better speeds with a different set-up that won't break the bank? Preferably Mikrotik routers.
i think so....Use the SNTP Client to setup the correct time from some ntp server.
depends on what you will use. maybe you need DHCP to get IP address from the ISP. maybe you need ntp to get date and time. Maybe you need Security to get SSH access to your device. If not, then yes, 2 packages will be enough
strange!!!but the proplem is in the wireless connection , not in the modeTry to use Station-bridge instead of station-wds.
yes ..........Anyone who have the same problem as I have?
which kind of sector antenna you are using ?! ..why you want to use single chain ?...anyway u can used it as you like and dont worry about the safe and the configurations.........can I safe use it with single chain antenna, configuring the ht-rxchain and ht-txchain?
I have an AP (RB433AH with 2 miniPCI) connected to 2 sector antenna, as my base stastion.
absolutely no....one connector for chain 0 the other for chain 1.....need to know another thing i see 2x MMCX connectors can make one antenna Ap and another Client ( station ) ??
is this real signal levels or am I going o burn out the transmitter by running it too hot?
from my view point ...the best way ,is by user proflie ( hot spot & pppoe )...What's the correct way to achieve bandwidth limitation and priorization of VoIP traffic on the CPE side (SXT 5HPnD)?
Why should I adjust noise floor threshold to -120/-124 ?
Thanks,
90% your suppose is right....so i suppose that my satalite modem speed is not enugh.
do you mean that there is a relationship between the rx ccq and tx power of the wireless device ??try to lower the wireless Tx power
but the rx ccq = 45% is that bad ??......with thankI have no explanation for your problem, but it seems your signal is waaaay too strong. Try to get it below -40. -40 to -60 is best.
wds to extend the coverage ....so .what is the issue??Hi to all,
actually the only protocol that extends a wifi coverage is wds?
dont make me crazy......i have two rb 912...this is one of my rb912...im from iraq....laithmikrotik this is not the product they are talking about. You have a Stationbox, it's different.
try use free access account to ap and see what happeni have the wireless protocol set to any and the band is bgn.
thank you very much.......now i understand you.......
There is no direct relation to "signal purity" as you state that and CCQ. In wiki you can read what it is and how that is calculated.
good idea ...thank you very much.Yes you can.
But rb912 have L4 and is expensive. Do you need L4? If not, and miniPCIex is not required then is enough rb911
at first you did not give me a karma....please give me a karma.thanks a lot
my link is ok now:)
what happen when I change mode to station pseudobridge?
thank you ...but -3 is stronger 20times than -65......That's way too much signal. Try lowering the TX power of each radio until you get around -65 to -70 signal and see what happens.
thank you very much...God bless you............You have an older model, the SXT-5HnD. It is possible that you need to contact the seller for an RMA.
yes ...exactly ....the sxt is still deadYou don't need to wait until it flashes 25 times, but when flashing stops and LED turns off. Does that happen?
do you mean i have to use 2 RB'S . one for each polarity..this is very strange ..!!!!!!!!!!2 RB's would have a smaller separation between chains than a single one and problems may ocur.
thank you but i have another important question ...what is the best ?711GA-5HnD has a level 4 license.
thank you ...but RB711 have a license level 3 .........and i dont know how to upgrade to license level 4 ( acess point ) ..So connect just one dual chain Rb711 5hnd and choose at the client what polarity should use. Big deal...
You would not believe us.
Quite the contrary.i like all members of the Forum ..it was just an idea and I liked it's application .. greetings and appreciation to all members .You are determined to use that setting. Good luck.
i dont thing so ..it has worked since 5 days (24h/day) and nothing happened till now..leave the card in default....
xr5 has a 8dbm offset tx power.....
if you set those 27dbm you will burn the card... very soon!!!
What do you mean about the cameras?
my friend ..just delet it from the desktop..and re-install ithow can removing the tool on a PC (or clearing its cache) help in repairing failing hardware?
dont worry about itwhereas the link speed on the Station Bridge is shown as Tx = 52.0Mbps and Rx = 58.5Mbps
http://routerboard.com/RB711-5Hn-Mdoes any one know what wifi card is in the SEXTANT (I would like to use MIMO)
other Q
can i use minipc mikrotik 800Mw with RB433
IT will work with no problems ?????????
thank you ...i will give you a karma4w2d is how 30d 00:00:00 got exported, and if you need it to be every 5th day, then just write 5d
I always enable all chains and SXT connect to Hpol Or V pol fine. Is there any advantage to disabling chains when connecting to single chain APs?
sorry .this is the first time i hear about thatit is linear horizontal or linear vertical, these are not 3 different polarizations.