MikroTik

onlysuraj

please have a look ????

onlysuraj

thanks for you input , i have configured as below according to wiki But i have to manage all device (p2p access point ) through it So one of the port required for access all devices for maintaince purpose ( like cisco switches ) because it is so difficult to visit all site to check connected p2p and...

onlysuraj

hello everybody, i have a simple question I have just replaced cisco 2950 switch with mikrotik crs125-24g-1s-rm And now i want to configure port based vlan on this switch: port 1 as uplink and 2-23 will be access port and 24 port will be for manageable purpose , beacuse all access port and p2p are c...

onlysuraj

MPLS will just make your setup so more complex. You still need the bridging etc. Just bridge a VPLS interface instead of a interface directly conected. If you still MUST have MPLS, its possible to setup. Make a bridge interface at your 1100 call it somethig like loopback, and put a IP to the interf...

onlysuraj

i am trying to make mpls/vpls tunnel between 1100ah(userman is installed here) and 433ah routers.so that i can access the internet through mpls/vpls tunnel. main access concentrator : [admin@main access concentrator pppoe server ] > /ip address print Flags: X - disabled, I - invalid, D - dynamic # A...

onlysuraj

hello there, i have a simple stupid question because i don't know how to do this because there are so many ways to accomplish this but i have to done this as simple as i can so the question is i have setup the pppoe server for 100 clients for a building, so that i made a pppoe server with usermanage...

onlysuraj

Have you enabled airmax? don't do that

See you de ssid from accesspoint side

thank you for comments

yes airmax is enabled

and i will coment back after disabling the airmax on ubnt devices because this is on production network....

thanks

suraj

onlysuraj

Hello all of you i am facing a problem so , for easly understanding i am attaching an image and ap and station configuration :: access point side [admin@MPLS_AP] > export hide-sensitive compact # jan/02/1970 04:23:23 by RouterOS 6.7 # software id = NHFA-6QC9 # /interface bridge add l2mtu=1500 name=b...

onlysuraj

hi guys last two days i am facing a problem with sxt 5nd r2(5.26) . they are in point to point bridge mode (wds) and every 1 or 2 min ap side ether port going down in log . can anybody tell me the why this is heppning and what is the reson. is there any body faceing with same promlem. thanks and reg...

onlysuraj

i have solved my problem

thanks

onlysuraj

finally i have successed to access via usermanager to users (that are created i usermanager )
but they are not able to obtain ip address from dhcp server (i have checked all the setting of dchp server but working)

please help

onlysuraj

Set 127.0.0.1 for /radius and /tool user-manager router. Do you have /ip firewall nat rules for masquerade? dear sir, i have the same problem ? yes i have done this /ip firewall nat rules for masquerade i have done all the setting well but i can log in through usermanager users but i can log in by ...

onlysuraj

the first thing you should check is Goto tools/ping and try to ping 8.8.8.8 if it seems ok ,so you should check your connection between mikrotik and clients ,and remember according to wiki you put ip of eth1 as dns server it seems when you try google.com it goes to nowhere ,you should change it wit...

onlysuraj

the first thing you should check is Goto tools/ping and try to ping 8.8.8.8 if it seems ok ,so you should check your connection between mikrotik and clients ,and remember according to wiki you put ip of eth1 as dns server it seems when you try google.com it goes to nowhere ,you should change it wit...

onlysuraj

hello everybody, i am trying to make pppoe server on mikrotik 450 g router for 50 clients for my office . i have read this post on wiki : wiki.mikrotik.com/wiki/Pppoe_server_with_profiles i have done all the setting and after creating pppoe clients when my pc is connected to pppoe server it works fi...

onlysuraj

RB1100 supports fairly good amount of concurrent connections with queues, firewall etc. I have heard from people that have around more then 300 concurrent connections without any issue on RB1100. thanks for your fast reply sir :) after apply mangle rule response is good but this wil be specific for...

onlysuraj

Actually its common, because Queue limits ICMP packets too. If you are just worries because of high latency to mikrotik, simply create a queue that allow some access bandwidth just to ICMP protocol. http://aacable.wordpress.com/2011/12/07/mikrotik-howto-give-ping-icmp-high-priority/ Thanks sir, now...

onlysuraj

Don't' ask what is better for your network , Do some research , then compare them, then try to use them in lab environment or with very few users, then judge on your own. Only you can be the best one who can decide what is better for your network. I will not comment on 'Simple DHCP', as its not wor...

onlysuraj

Don't' ask what is better for your network , Do some research , then compare them, then try to use them in lab environment or with very few users, then judge on your own. Only you can be the best one who can decide what is better for your network. I will not comment on 'Simple DHCP', as its not wor...

onlysuraj

Depends on the situation. For a hotel, hotspot is better, for an ISP, PPPoE might be better. Without knowing your situation both could be good. Thanks for your fast reply frnd , I am taking about as an isp . but there is a problem with pppoe this needs extra cinfiguration at client side. i have got...

onlysuraj

hi everybody ,

i want some information ,which one is best hotspot server or pppoe server.

onlysuraj

hi frnds i have configuring p2p link with 711 5hnd using mpls/vpls protocol.... everything works fine but suddenly link goes down and gives RTO** but after some ROT link works after 7 to 8 RTO ..................... so what is the problem Can any body help me in this regards ........ and one thing i...

onlysuraj

hi frnds i have configuring p2p link with 711 5hnd using mpls/vpls protocol.... everything works fine but suddenly link goes down and gives RTO** but after some ROT link works after 7 to 8 RTO ..................... so what is the problem Can any body help me in this regards ........ and one thing i ...

onlysuraj

hello everybody i have a problem with static routes configuration ? For one of the location where i am working now, isp provided us one /30 wan ip add and two /29 lan (public ip address pool) that i want to configure on mt 1100ah router,but i can't do that. suppose i have one wan ip 10.0.0.5/30 wher...

onlysuraj

mmm one answer.... the NV2 its not compatibl whitz ? and a dnt undest these problem regards any has comment on it :) there is any problem in router ros 5.6 5.9 had improvements in NV2 signal to noise level 5.11 had improvements in disconnect issue. Why are you still at 5.6? NV2 does work with WDS f...

onlysuraj

mmm one answer.... the NV2 its not compatibl whitz ?
and a dnt undest these problem
regards

any has comment on it

there is any problem in router ros 5.6

onlysuraj

Looks alright at first glance. Could you tell more about the actual symptoms you are seeing? How exactly are you performing a test to identify the issue? You say latency is too high. How high? And how are you testing? i have maintainoed that in earlier post. continously i was checking the perfomanc...

onlysuraj

1> bandwidth test with TCP is CPU intensive. Use a separate device to generate traffic. 2> Create identical wireless security profiles on both sides Use same NV2 key in NV2 setup on both sides NV2 *does* *not* use wireless security profile! 3> Date rate selection Advanced allows both radios to sele...

onlysuraj

I don't see anything wrong with your setup that would cause really bad issues. Make sure to use NV2 security. Use rate-selection=advanced. What are your ccq readings? what are the signal strengths? thanks for your input dear :) ya i have configured wpa2psk security on nv2 tab of wireless card. and ...

onlysuraj

I don't see anything wrong with your setup that would cause really bad issues. Make sure to use NV2 security. Use rate-selection=advanced. What are your ccq readings? what are the signal strengths? thanks for your input dear :) ya i have configured wpa2psk security on nv2 tab of wireless card. and ...

onlysuraj

Post terminal output to /interface wireless export hide-sensitive Upgrade to 5.14 as well. Check for clean channel using scan and freq usage. at ap side /interface bridge add admin-mac=00:00:00:00:00:00 ageing-time=5m arp=enabled auto-mac=yes disabled=no forward-delay=15s l2mtu=1598 \ max-message-a...

onlysuraj

hi everybody gud evening,i am just trying to configure point to point link with 7115hn ros 5.6 but link is not stable there is too latency when client starts download and upload. so we posponed this setup. i think there is some setting issue at ap side mode= bridge band =802.11N(only) frequency 5180...

onlysuraj

Your Wellcome ... if you have any question , i can help you my friend ... sorry for disturbing you frient but i have a problem with redirecting to or from squid server this is setup for internel lan wan link is on mt 450g (ether1)10.210.2.5/24 ether2 connected to squid (with single lan card)192.168...

onlysuraj

Web proxy server and filter by url policy should do it..

/ip firewall filter add action=drop chain=forward content=facebook disabled=no src-address=10.210.2.7

where 10.210.2.7/24 is your internal lan ip ,whatever your is ???

onlysuraj

Is this squid in fully transparent mode you - then you need to consider L2 redirect or policy routing. Otherwise you could simply look at http://aacable.wordpress.com/2011/12/30/howto-add-squid-proxy-server-with-mikrotik-short-reference-guide/ as a good start. thanks for your reply :) yes this is f...

onlysuraj

hi everyone i am just trying to implement squid server in my lab. this is for my small setup for testing. i have configured the squid well and my network setup is ehter1 -internet------mt450g | | | |ether5(for lan connectivity ( squid)| | switch here main link comes to mt routervoard ehter1 and ethe...

onlysuraj

U will never learn :) U can NOT route them! Your idea is completely wrong! the only way to use those 3 networks after your Mk, u have to purchase them from only ONE ISP! then u have to run BGP on Mikrotik and route them.... but all this will happen with the support of your ISP! tell me how those 3 ...

onlysuraj

U will never learn :) U can NOT route them! Your idea is completely wrong! the only way to use those 3 networks after your Mk, u have to purchase them from only ONE ISP! then u have to run BGP on Mikrotik and route them.... but all this will happen with the support of your ISP! tell me how those 3 ...

onlysuraj

One way is to ask itself. CMD line system routerboard print. Andre thanks dear at cmd :> system routerboard print 411ah was there i thought this was froad ........ but on routerboard there was only printed as 411U and i asked for 411ah so i asked for that (on fouram) :) after all thanks for ur input

onlysuraj

is this possible to use wan1 link for some coonection and wan2 for another connection.both link comes to mt450 and from mt450 to linux box that contains usermanagement software that is used to control user behaviour then my internal netwok start(10.210.2.0/24) NO! both link comes to mt450 and from ...

onlysuraj

good evening fellow i want to ask a small question ??? recently i purchaged a roterboard 411ah anf they sent me through parcel, when i saw the board there was typed 411u. and one more thing ,In winbox at resources button there was indicated cpu 680mhz and ram is 128Mib but on the mikrotik site there...

onlysuraj

this could never happen! what U can do is to put the public IPs on the Mk on ether1 and ether2, and configure a network between Mk and Linux and NAT the network! Then on Mk do fail-over or load-balancing. If you get 5mbps from ISP1 and 10 mbps from ISP2 you can NOT get 15 mbps at the end..... "...

onlysuraj

Pf... IS there a anything between Mk and ur Linux? or just a cable connection ? at first i want to say thanks for your reply. ehter3 direct connected to linux server with cable. actually at pressent my current setup is same as i maintained in the image but the difference is router that i am using c...

onlysuraj

So much with my Arrogance! 1. Why do u need an IP pool for a network between ur Mk and ur Linux ? 2. Why do u need two IP pools for that, as well? :) Just put the first provided IP address on ether1, the second on ether2.... Put 192.168.0.1/30 on ether3 and 192.168.0.2/30 on ur linux and do fail ov...

onlysuraj

good afternoon my question is i am configuring two wan link on mikrotik 450g router.both isp provided me public ip and lan pool. for example wan1 10.0.0.10/30 and with lan pool 10.0.10.90 to 100/24. And 2nd isp gave me the wan ip 172.16.0.10/30 with lan pool 172.16.0.70 to 84/24.after creating inte...

onlysuraj

good afternoon my question is i am configuring two wan link on mikrotik 450g router.both isp provided me public ip and lan pool. for example wan1 10.0.0.10/30 and with lan pool 10.0.10.90 to 100/24. And 2nd isp gave me the wan ip 172.16.0.10/30 with lan pool 172.16.0.70 to 84/24.after creating inte...

onlysuraj

good afternoon my question is i am configuring two wan link on mikrotik 450g router.both isp provided me public ip and lan pool. for example wan1 10.0.0.10/30 and with lan pool 10.0.10.90 to 100/24. And 2nd isp gave me the wan ip 172.16.0.10/30 with lan pool 172.16.0.70 to 84/24.after creating inter...

onlysuraj

I don't think you are actually asking a question. Anyway, you don't actually configure dhcp on a wireless card, you configure dhcp on an interface. Winbox -> IP -> DHCP Server. See the wiki for more information. thanks for your reply. after creating dhcp server and pool.and selecting the wlan as dh...

onlysuraj

I don't think you are actually asking a question. Anyway, you don't actually configure dhcp on a wireless card, you configure dhcp on an interface. Winbox -> IP -> DHCP Server. See the wiki for more information. thanks for your reply. after creating dhcp server and pool.and selecting the wlan as dh...

onlysuraj

good after noon to everybody my question is i am configuring an access point. currently i have configured them as ap bridge and client are connected through ip range (10.210.2.2-254)and 10.210.2.1 is the gaeway for all client.now i want to all access point work as gateway for the wireless client.(t...

onlysuraj

good after noon to everybody my question is i am configuring an access point. currently i have configured them as ap bridge and client are connected through ip range (10.210.2.2-254)and 10.210.2.1 is the gaeway for all client.now i want to all access point work as gateway for the wireless client.(t...

onlysuraj

good after noon to everybody my question is i am configuring an access point. currently i have configured them as ap bridge and client are connected through ip range (10.210.2.2-254)and 10.210.2.1 is the gaeway for all client.now i want to all access point work as gateway for the wireless client.(th...

onlysuraj

Just create the VLAN interface from the interface menu in the MikroTik. A VLAN that is added is treated like any other routed interface, you can run whatever services you want on it like any other physical interface, DHCP, Hotspot, PPPoE, etc. Keep in mind that this is a router and not a switch, it...

onlysuraj

hi good morning everybody, my question is we are taking another 15 mb link for backup on mikrotik router 450g. but the problem is they are providing wan connectivity through vlan cofiguration and they don't know how to configure vlan on mikrotik 450g even i don't know. they are asking for another r...

onlysuraj

hi good morning everybody, my question is we are taking another 15 mb link for backup on mikrotik router 450g. but the problem is they are providing wan connectivity through vlan cofiguration and they don't know how to configure vlan on mikrotik 450g even i don't know. they are asking for another ro...

onlysuraj

one more thing i have noticed that only orange light is coming and green light is not buring. is there any problem with 450g router. Possibly. Console in - does the link show up? Does that cable work when you plug it into something else? Everything else you're asking about is covered by the wiki ar...

onlysuraj

one more thing i have noticed that only orange light is coming and green light is not buring. is there any problem with 450g router. Possibly. Console in - does the link show up? Does that cable work when you plug it into something else? Everything else you're asking about is covered by the wiki ar...

onlysuraj

http://wiki.mikrotik.com/wiki/How_to_configure_a_home_router one more thing i have noticed that only orange light is coming and green light is not buring. is there any problem with 450g router. and about setting wan ip 10.210.2.1 for wan and for lan 192.168.1.1 for lan than i configure dhcp client ...

onlysuraj

and why will you want to do that??

for better throughput and faster data transmit
that's all

onlysuraj

good evening everybody (i need urgent help?)

i can't configure the mikrotik 450g mikrotik router at all.

i have done all the thins but not done

can any body send me me the example for how to share the inernet connecction.

and i also read the topics but not clear

with regard from
suraj

onlysuraj

you want to connect your customers to a single ap?

yes ,currently there is one sector anteena that is access point and client connect to it .
but i want configure one for tx and other sector anteena for rx .
is this possible. (2.4ghz)

onlysuraj

hello gud morning to everybody here my question is i want to implement double sector anteena for my client that are connected by 2.4 capable cpe . is this possible if yes then how curently all access point are confirgured as ap bridge (no routing ) and also want to know about in 5.8 ghz respectevly....

onlysuraj

Ok, change ANI (Adaptive Noise Immunity) to Client and AP mode on each interface running as client. Secondly, I see you have a mix of 802.11b and 802.11g clients connected. Meaning the whole network degrades to a ´b´ network anyway. I need to link quality of each single client. SNR (Signal to Noise...

onlysuraj

Ok, change ANI (Adaptive Noise Immunity) to Client and AP mode on each interface running as client. Secondly, I see you have a mix of 802.11b and 802.11g clients connected. Meaning the whole network degrades to a ´b´ network anyway. I need to link quality of each single client. SNR (Signal to Noise...

onlysuraj

Still not so much info. All I can distil of the pictures is that both AP running cards have some clients attached and some traffic is running over the AP's interfaces. Furthermore both wlan interfaces show low CCQ's which means the average package loss over the wireless is high. This can have sever...

onlysuraj

Yes, show us the full configs and also tell us how you do the speed test? There can be many things wrong but a 433 is definately able to supply much higher speeds. Side note: rb433 is only the routerboard. It is depending the wireless card and how it is configured on what the wireless performances ...

onlysuraj

hi good evening i have a question about 433 radio, configured as access point and connected with sector anteena . its receiving is too low. i cheched everything pigtel, wire and all things but the radio tx goes to 1100kbps but the receiving is about 50 to 100kbps.is this ok or i have configuration i...

onlysuraj

not possible thanks normis actually before me one of the tower is installed with 433(three card) last year. and now the customer base increasing ,so i want to install more powerful wireless card on it. so i was asking to how could i know the wireless card model no. can you tell me which wireless ca...

onlysuraj

it is safe to reset the configuration with all the interfaces attached.

thanks,
i was thinking it will harmful for wireless card?

onlysuraj

hello everybody
good evening
one simple question ,i want to know the wireless card model no that is located on the tower.
and i want to know that model no by winbox.

plz tell me that how do i find out that?????

plz
anybody know that???????????????

onlysuraj

hello everybody
good evening
one simple question ,i want to know the wireless card model no that is located on the tower.
and i want to know that model no by winbox.

plz tell me that how do i find out that?????

onlysuraj

configuration remain same as .rsc file on RB333 in routeros v4.3
than what will be issue in routeros v5.6 ?
request to reply soon

is this safe to reset the routerboard with wireless card or just remove the card before reseting.

onlysuraj

http://wiki.mikrotik.com/wiki/Manual:Password_reset
thanks normis,for you reply,
good luckfor me
ok i am trying again. ??

hi there good morning
it is not reseting at all

one thing the router board is not receiving the data packet.
so, is routerboard is dead???????????

onlysuraj

http://wiki.mikrotik.com/wiki/Manual:Password_reset

thanks normis,for you reply,
good luckfor me
ok i am trying again. ??

onlysuraj

get ur board down and do a reset. u have put some clumsy setup in the ip which is conflicting somewhere in ur LAN hence the issue i read the fouram but don't clear abut how to reset the board plugging the power on then hold the matel part preesing with screwdriver for a time when a short beep comes...

onlysuraj

get ur board down and do a reset. u have put some clumsy setup in the ip which is conflicting somewhere in ur LAN hence the issue i read the fouram but don't clear abut how to reset the board plugging the power on then hold the matel part preesing with screwdriver for a time when a short beep comes...

onlysuraj

check if the IP on ur PC is in same subnet at u have assigned to the router. If it is, winbox discovery would show the IP of the router. If it is not, winbox discovery will show the mac address. The only thing that might be the case is that if the PC and router are on the same subnet and also have ...

onlysuraj

tommoarrow i had configured the 411 routerboard with two ip one is for ethernet 192.168.1.50/24 second for wlan 10.0.0.5/24 but after one day i am trying to access the router then two ip comming in winbox that is wlan ip and second one is the same now i don't undersatand what to do can't log in thr...

onlysuraj

tommoarrow i had configured the 411 routerboard with two ip one is for ethernet 192.168.1.50/24 second for wlan 10.0.0.5/24 but after one day i am trying to access the router then two ip comming in winbox that is wlan ip and second one is the same now i don't undersatand what to do can't log in thro...

onlysuraj

Check the order of your rules. Put the rule I gave you at the top and see if that works. You could have another rule accepting the traffic before it is suppose to get dropped. how fool i am :( thanks man it's wirking now the 10.210.2.14 can not access the facebook.early moring customer told me that...

onlysuraj

The target address on your simple queue is 10.210.2.37, which shows up nowhere in your netwok diagram or your exported configuration. What is that IP address? Also, you're running 3.22, which is slightly older than too old. Upgrade to the latest version. ok the real ip that is in my network 10.210....

onlysuraj

my answer could not be complete. i need a design of your network. 1. using r52h ad 24dbi anenna you can cover a distance of 20km in LOS 2. nstream must be enabled: it guarantees higher speed, lower latency 3. you can configure the default gateway hello rodolfo thanks but i did not get my answer yet...

onlysuraj

Try something like this.

/ip firewall filter add action=drop chain=forward content=facebook disabled=no src-address=10.210.2.14

thanks for fast reply
but it is not working any more
kindly post some specific codes

onlysuraj

If customers are assigned static IPs then it is so easy for you to add dropping rules through MT firewall, first of all your schema is a bit unclear but what I understood is that you need to block facebook for some clients knowing that these clients are assigned Static IPs, therefore collect the IP...

onlysuraj

If customers are assigned static IPs then it is so easy for you to add dropping rules through MT firewall, first of all your schema is a bit unclear but what I understood is that you need to block facebook for some clients knowing that these clients are assigned Static IPs, therefore collect the IP...

onlysuraj

hi friends some customer compained me that they want to block the facebook and orkut like social site from our end. these customer are connected to the access point (2.4)and all are using static internal ip that are provided by us . now i am not able to do that bcos if configure the firewall on radi...

onlysuraj

Firewall filtering is easy, the key is figuring out what you want to allow and what you don't. Start with the basics: 1) What are your sources and destinations? WAN or upstream links? LAN or downstream links? 2) Which sources (originating addresses) do you want to have access to the router itself? ...

onlysuraj

my answer could not be complete. i need a design of your network. 1. using r52h ad 24dbi anenna you can cover a distance of 20km in LOS 2. nstream must be enabled: it guarantees higher speed, lower latency 3. you can configure the default gateway hello rodolfo here is my network diagram kindly tell...

onlysuraj

The target address on your simple queue is 10.210.2.37, which shows up nowhere in your netwok diagram or your exported configuration. What is that IP address? Also, you're running 3.22, which is slightly older than too old. Upgrade to the latest version. ok the real ip that is in my network 10.210....

onlysuraj

The worst thing you can do is install a firewall rule set you don't understand. If the wiki doesn't make sense to you, keep reading. Installing rules that drop packets when you don't understand how they work is going to lead to your devices dropping packets you don't want them to, and customers com...

onlysuraj

The important parts are "/queue type export" and "/queue simple export" or "/queue tree export", depending on which ones you use. It's hard to troubleshoot queues without seeing the queue configuration. Also, any chance of you taking a screenshot of your network diagra...

onlysuraj

http://wiki.mikrotik.com/wiki/Firewall Always search the wiki and forums first. thanks fevi but i cant understand how apply on my point to point link as well as at access point . here is the access point details [admin@radio1] > /interface print detail Flags: D - dynamic, X - disabled, R - running,...

onlysuraj

[quote="fewi"]Post some details. Start with "/interface print detail", "/ip address print detail", "/ip route print detail", "/ip firewall export", "/queue tree export", and either "/simple queue export" or "/queue tree expor...

onlysuraj

hi everybody i tried too much to configure the mikrotik pcq through winbox but it is not configuring at all. the configuration is-: created two pcq one for up load and second for download and give the speed limit after just add to the that user ip with that and interface is set to ether 1 that is th...

onlysuraj

for the first time i am configuring the firewall on p2p2 link and for accesspoint radio. so i can't understand the how to enable firewall on radio and p2p link. if want to block visus nd only allow this address 192.168.1.1.254 then how it will be configured can any send me the sample firewall rules?...

onlysuraj

my advice is to use ospf: http://wiki.mikrotik.com/wiki/Manual:OSPF-examples suppose you have some sites of installation. each site have one switch; the switch connect p2p, pmp, and other servers. in each site, all eth connected to the switch have a subnet /24; each radio link p2p have a /30. then ...

onlysuraj

i am using 433ah roiterboard with ap bridge mode how can i encrease the tx/rx on router to gain maximum throughput? what configuration i need???? currently i have 15 customer on it and how much customers it can handle. help??? Are u from india if yes...contact me on sanghera dot jatt at gmail dot c...

onlysuraj

If u want to use this for the 60km link u first try and connect at 802.11. Then u go for Nstreme after getting signal levels less than 75 db else u will never be able to connect ur radios. hi i want to configure the link across 5 to 6 km. as you say at first i connect both radio using 5ghz band, br...

onlysuraj

the better is not possible to say, because it depend on the application. if you have a simple installation, bridge could be better but coud be better routing in case of any requirements. post a design and describe what you want to do and we can help you. hello rodolfo this is our network setup link...

onlysuraj

We are getting 8-10 mbps UDP with bandwidth test on rb711 with grids on both sides and signal -69/70 ccq 70/75% thanks for replying but i am using inbuilt anteena 22dbi and signal and ccq is good now we are encreasing the bandwidth on it (6mbps), is there any touble . can i mount an external anteen...

onlysuraj

F-Com sectors r being sold a lot in India. For 1 mbps link at the client site I would recommend a rb711-2hn. Tplink is ok but if u have simultaneous users it will fail. We are using 22 dbi boxes for links above 1km till 3 km depending more on LOS conditions as well. 50 clients on 3 sectors and 1 RB...

onlysuraj

hi there i made a p2p with 7115hn and is configured in 5ghz (bridge mode ) and freq is 5280 band is 5gh only N cust complain that they can't gaining the 4mbps link. we are providing 4mbps link on it. signal strangth is -69 both side. and tx/rx ccq is 89/92remote site the remote site is approx 5km aw...

onlysuraj

u can use 22dbi boxes. whr in india r u. i know a few suppliers. hi thanks for replying we are located in east india and basically a hill station and i want to know that what sector anteena and rrouterboard is responsible for the best tx/rx what sector we should use, at present the sector anteena i...

onlysuraj

if you re-use frequency, use different polarity

thanks for replying
i w'll check this

thanks very much

onlysuraj

yeah you can use the same freq. better to use different frequ. to each pointto point

thanks for replying imran ,
but my question is can i use same frequency at my access point in same network.
bcos i have 13 access point and how to assign freq among them (2.4ghz) . do you have any idea
plz help????

onlysuraj

hi there i have a problem i deplolyed 13 access point in my network and i put two access point in same freq.is this possible both ap far away from each other . is there any problem with this . in upcomming days i will deploy three more access point how i willl manage the freq. can anybody tell me th...

onlysuraj

hi all i am configuring a new point to point link and i want to do a new kind of p2p with nstreme how do i configure the in nstreme devices are - 411ah(2) 24 dbi grid anteena (2) r52h wireless card (2) if i can configure p2p with this then somebody tell me how it is possible????????? i will thank fu...

onlysuraj

use a higher gain antenna for the client that is far. See if ur LOS is clear

what type of anteena i can use currently i am using 12 dbi anteena in tp link 501g.

onlysuraj

hi everybody i am facing a problem.my two client is far from my access point and seven client are 500 m away from the access point . client that is closed to the access point are gaining best throughput and for client that are 1km from my access point, are not properly replying and ping from that is...

onlysuraj

configure one point as bridge and the other point as station. assign an /30 subnet to the link and you an ping between them thanks for reply and i want to know what is best routing or bridging how to do routing (simple) is it correct mode=bridge freq =5200 ssid =abc and now after creating wds ,wds ...

onlysuraj

Bridge > Settings > Check "Use IP Firewall", just as described in the post you're quoting. If you're not having the same issue you'll have to post a lot more details, though. hello everybody , i am just trying to make simple queue. through winbox - queue-and make a queue_type= pcq (one fo...

onlysuraj

After eating some lunch and getting the brain some fuel. I looked over the settings and forgot to check use ip-firewall under the bridge settings. My goof! Food does wonders. Now the simple queuing is working. Thanks for reading my post. -Brian hi i am doing the same thing and facing the same probl...

onlysuraj

hi
i am configuring a point to point link ,i configured it as
mode = bridge(411ah board)
freq= 5200
wds enabled = dynamic
is there any other way to configure the point to point link for best performance.
if i configure wds =sataic
then what should i do?

onlysuraj

hi everybody

i want to deply omni anteena with 433 router .
so can i configure the omni as access point.
is there any compaibility problem,what omni should i use with 411 or 433 board (in 2.4)

onlysuraj

if you would like to setup AP directly between two interfaces then you have to bridge them (your internet source interface with wlan interface). Don't forget to select "AP-Bridge" mode for wlan. thanks for reply but i have configured it as access point (bridged). so kindly tell me the add...

onlysuraj

hi everybody i have configured an access point with rb433 (three card). and sector anteena is 17dbi what is anteena gain ?what is the adject number of anteena gain .i configured it 17 dbi. and what frequency i would use in 802.11b mode . i configured it 2452 and what is adaptive noise immunity(by de...

onlysuraj

I'm sure, that there are plenty of people eager to help you... ... just after you paste your queue config and explain exactly the goal you want to achieve ;-). (simple "/queue export" takes less than 15 seconds :) ) hello dasiu the problem is when i configure queue option for bandwidth ma...

onlysuraj

if you are using, http://routerboard.com/RB411AH Use Null Modem cable and get console output by COM port, http://wiki.mikrotik.com/wiki/First_time_startup#Serial_Cable hello dasiu thank you for your help . it's working now i can access the through mac add and now i can log on to the router (411ah) ...

onlysuraj

Maybe mac-telnet will work? If the problem is in firewall - I assume you block only IP communication, mac-telnet (or mac-winbox) should still work...

hi dasiu
thanks for replying,
but the router is not visible in winbox
is there any mathod to know the mac add of my router

onlysuraj

hi everybody
i have cofigured wrong firewall script on my access point ,and now i can't log on to that router board (411ah) which is configured as access point (ap bridge mode) .

plz help
it's urgent

onlysuraj

hi all
i am trying to make queue on rb433ah. but on single radio works good but at 433 with three card this is not working.
what interface i should use for clients at ap1 ,ap2 ap3
can anyone help me for this.

onlysuraj

just add the ip in queues option and rember to select the interface for that ip . if you forget to select the interface than it will create trouble for you . after you add the quese give tham the specified speed in max speed and min speed . than we we run script in terminal the command is interface...

onlysuraj

hi everybody , i want to configure the vlan in my network my network diagram is AT first , link -450g(router)-server-switch-all access point connected to the switch. now can you guide me to create vlans -at which point i will create vlan at switch or access point radio (433ah or 411) i am new in mik...

onlysuraj

use the queues option this will solve the problem. how to configure the queue option ??? currently rb433 is configured access point (bridged ) can i configure routing. is it good than briged network mode =ap freq 2447 band= b+g and all customer are connected with diff diff speed plz tell me how to ...

onlysuraj

hello everybody i have some question: (1)can i enable nstreme on rb411ah or rb433 routerboard configured as access point (2) what is anteena gain and what it should be ? (3)what is ack time out on the wlan interface advance page? (4)what is tx power mode what is good card rate or all rate fixed kind...

onlysuraj

i told you use queues option . or please give me your networking scnario so that we can look into your problem I have 433 routerboard with three card r52 and made it as access point(router os v 4.11) .simply user connect to it and access the internet via server and a 450g configured as firewall in ...

onlysuraj

http://wiki.mikrotik.com/wiki/Transpare ... o_Networks

thanks ,
but i want it through winbox
and what should i do for maximum throughput .
plz tel me?????

onlysuraj

hi
i want to know how to configure the p2p link on mikrotik rb411ah using wds bridge
what should i do???????????

onlysuraj

hi everybody i am facing a problem. a site with 433ah with three in one : three sector is connected to that and arount 15 to 20 customer on that radio. the problem is all customer are not getting the full speed and time=ms is breaking, and every time i change the frequency and band. some body help m...

onlysuraj

hello
how to configure firewall on access point and how it will configure . in detail

can i purchage the firewall rules or free download

onlysuraj

hello
i am using rb433 as access point and how to encrease tx/rx on rb433.
currently 15 user running on it and is not working so good.
plz help????

onlysuraj

i am using 433ah roiterboard with ap bridge mode how can i encrease the tx/rx on router to gain maximum throughput?
what configuration i need????
currently i have 15 customer on it and how much customers it can handle.
help???

onlysuraj

bump.
hello,do you know another forum about RouterOS?
can you introduce some for me?
Please in English.thank you .

my mail/MSN:macxie2010@hotmail.com

？？？？？？？？？？？？？

http://blog.butchevans.com

onlysuraj

hi everybody i am suraj and i am newbee in mikrotik world.
i just want to know can i enable wds mode= dynamic on ap briged radio 433ah

Search found 134 matches