I have created one bridge port in Mikrotik and add five ethernet port with bridge port. with bridge port more than 250 customers are connected . once customer remove from mikrotik (bridge port ) their MAC & IP not deleting from ARP table automatically.
There may be opened port redirections by upnp. Check it, close the redirections and drop the connections. Implement common firewall rules that will not allow incoming traffic if not requested from inside. Can you provide sample firewall rule to Implement common firewall rules that will not allow in...
If you base the statement of packet direction on the fact that the IP is listed under dst ip in the torch listing, this is not correct. The src/dst should be read as remote/local (maybe it is time to correct this in winbox?). Hello, plz find the attached file. eth3 our local network and eth 10 is w...
Dear All,
We are getting huge no. of tcp & udp packet in our router from outside with multiple IPs which increase our uploading. can anyone suggest the solution to stop it.
Hello, I have CCR1016-12G router in my network. When we access this router through winbox v6.5 , router got disconnected automatically within 2-3 min. there is link connectivity issue in between my system to router. can anyone suggest the exact cause can be . I also attached the screen shot for read...
Hello All, Recently i buy CRS125-24G-1S Switch cum router for our network . currently i am using this device a router to terminate ISP link in port 1 and out from port 2 and simple default routing goes toward ISP. we are getting packet loss since router put into the network while when i directly con...
Dear All, We are using CCR1036-12G-4S router in our network and doing full bgp peering with upstream ISP. from some days we getting unnecessary uploading traffic in incoming traffic which hampering our network performance. In DNS cache its showing some unknown traffic which i believe some DNS amplif...
I hv done some configuration which is mentioned below. [admin@MikroTik] /routing bgp peer> print Flags: X - disabled, E - established # INSTANCE REMOTE-ADDRESS REMOTE-AS 0 default 111.93.178.37 7018 1 default 123.63.61.190 3450 ------------------------------------------------------------------------...
Dear All, I have CCR1036-12G-4S which will be used for multihoming bgp to connect 2 ISPs for load balancing. We have two /24 pools which will be routed through both ISP in their backbone. 170.84.28.0/24 170.84.29.0/24 Once both ISP up then 170.84.29.0/24 will route through ISP 1 and 170.84.28.0/24 w...
Hello, Recently i used in my network RB 450 for nating my private IP with public IP.. the problem is i m unable to access router xxx.xxx.184.66 from globally while nating is working properly with public IP . Configuration is below; Nat 0 chain=srcnat action=src-nat to-addresses=XXX.XXX.184.66 src-ad...
Hello, I have RB450 . I want to configure port forwarding toward our private IPs which is connected with our four DVR system. I hv only one live IP provided by our ISP. Now i want to access all DVRs through single live IP with different port from remotely. Live IP : 182.73.184.66 Private IP : 192.16...
What route will be accepted from ISPs i.e. default,partial,or full route. please let me know also the configuration of IP route , distance & routing mark in mikrotik
Dear All, I have CCR1036-12G-4S which will be used for multihoming bgp to connect 2 ISPs for load balancing. I have to /24 pools which will be routed through both ISP in thier backbone. 170.84.28.0/24 170.84.29.0/24 Once both ISP up then 170.84.29.0/24 will route through ISP 1 and 170.84.28.0/24 wil...
can we use Mikrotik 1100AH as it is L3 switch(i.e. cisco, zyxel,allied, juniper).
need to configure both Vlan trunk & access port in Mikrotik 1100 AH . port 1 to 8 will be the access port with different VLAN and port 10 will be trunk port ..