MikroTik

ganewbie

So in my case 6.48 on RB3011 does not (yet?) exhibit the port flapping problem even after cold start (when the new firmware becomes fully effective). But this is a very early box, bought just after 3011's introduction; maybe there are other HW versions of 3011. Ondrej In our setup we have 2 WAN por...

ganewbie

rb3011 flapping, 1500 linkdowns for about 30 minutes rb4011 seems to be fine Hi @rushlife I like to ask you, did you upgrade FW (bios) on your 3011 ? I ask this because my 3011 is up with v6.48 and it is stable - NULL link down's , all ETH ports 1G, up without problems but i forgot to update FW (bi...

ganewbie

Try this:
https://wisp.net.au/forum/t/wireguard-v ... teros-7/61

ganewbie

Hello,
Did you find a solution for this?
Thanks,

ganewbie

*) wireless - fixed Nstreme wireless protocol performance decrease; there was problem with Nstreme wireless protocol? since when? Would also like to know? Have only been around since N days. One link I could test showed no difference. Well, since there is no detail on this, I can share our experien...

ganewbie

So why Mikrotik produce the Netmetal Triple chain?
I see multiple antenna manufacturers have antennas and I see Netmetal 3x3, but not sure if it adds any value or it is nothing. I heard that it could double the download speed, no clue if that is true.

ganewbie

Guys,
Nobody is using Netmetal 3x3 with any antenna?
What do we expect in terms of performance with CPE such as sxt or lhg

I wonder if anybody is using the triple chain with any experience that could be shared.

ganewbie

Hello,
Does anybody got a chance to try the triple chain Netmetal with RF-element 3chain antenna 5GHz https://www.ispsupplies.com/RF-Elements-SEC-CC-5-16-HHV?
The CPE will be the regular SXT, LHG or ....
Do you expect more throughput?
Thanks in advance,

ganewbie

Thanks, macsrwe I believe I may have fixed the mysterious low CCQ and wrong distance. We changed the channel width to 20 instead of 20/40. Choosing a certain data rate helped a lot but we were trying by trial and error until we got a CCQ and the speed we are aiming to offer. Now the distance magical...

ganewbie

Hi Guys, We have an AP-Bridge with one client only (Station-Bridge). 1- CCQ is jumping between 60 to 90 all the time, never steady. 2- The distance on the AP shows 1Km (correct) but it shows 4 Km in the client. Any recommendations?! Attached is all the setups. # model = 921GS-5HPacD r2 # serial numb...

ganewbie

We are using LNS, PPPoE over L2TP tunnels, it works perfect and I recommend 6.39.1 as they have fixed couple of annpying bugs that was crashing some L2TP sessions in a special setup.
In our case Cisco is going out soon

Good job Mikrotik

ganewbie

Version 6.39rc72 has been released. Changes since previous version: *) l2tp - added support for multiple L2TP tunnels (not to be confused with sessions) between same endpoints (required in some LNS configurations); *) l2tp-server - added "caller-id-type" to forward calling station number ...

ganewbie

*) l2tp - fixed crash when rebooting or disabling l2tp while there are still active connections;

Hello,
Is this issue is the one related to LNS setup?
Thanks,

I will answer my own question, yes, it is concerning the LNS setup, I got confirmation from Mikrotik.

ganewbie

@ ZeroByte
What you are saying is amazing, and could be used even to protect web server with wordpress or Drupal.
Where could I read about firewall by layer 7 script?
I have been through the wiki but no luck yet.
Thanks,

ganewbie

Hello, We are using UserManager" as AAA server for DSL services connected with Cisco router as NAS. In "active sessions" window: There is a column called "Status" and under status there is couple of different options. We see "Start", "Interim" and "S...

ganewbie

6.35rc9 has been released. *) l2tp - added support for proxy authentication when receiving forwarded PPPoE sesssions; *) l2tp - added support for Hidden AVP, it is needed for proxy authentication; This fixes the issues with LNS function to carry PPPoE sessions over L2TP tunnels. Now it could replac...

ganewbie

I have done the opposite
From DMA to usermanager.
It was very manual process, good luck.

ganewbie

It happened to me too, and I found out by changing the MTU from the default of 180 to 1492, all sites open normally.
Again earlier did not notice but recently yes.
** I am using PPPoE** as gateway.

ganewbie

But what is the proper or required size?

ganewbie

*) l2tp: implemented PPPoE over L2TP in LNS mode, RFC3817;
Thanks a million

ganewbie

We have tested this with Cisco IOS LAC and it works perfectly.

Bring on Mikrotik LAC

We are scheduling test for the weekend, is it possible to share your settings?
How many PPPoE session did you see running on the L2TP?
Thanks,

ganewbie

It has been implemented guys,

Changes since 6.33rc33:
*) l2tp: implemented PPPoE over L2TP in LNS mode, RFC3817;

ganewbie

Great news, it looks Mikrotik implemented LNS.

Changes since 6.33rc33:
*) l2tp: implemented PPPoE over L2TP in LNS mode, RFC3817;

The challenge now is testing.

ganewbie

@ timoid
Thanks for the log.
Are you using usermanager to authenticate users?
I am assuming you will have hundreds of ppp session on the same one L2TP tunnel, Correct?
Thanks,

ganewbie

There is a user claimed that it has been implemented recently on the forum.
[img]

Capture.PNG

[/img]
We were trying to get more information but no reply yet.

ganewbie

Hi timoid,
Could you please shed more light on the way to set it up?
Which telco you have tried it with?
Thanks,

ganewbie

Thanks all,
We manage to get it working now I have more questions:
What is the recommended VPN that should give the best performance (not much latency) in this scenario?
Sure the SIP voice quality is not best but at least it is working but hope to improve it by any means.

ganewbie

Agreed,
I need to rout the SIP LAN address through office2 WAN IP.
The question is how? or what is the method and I will search?
Thanks,

ganewbie

Hello, We have two offices let us call office 1 and office2 Office 1 the ISP has blocked all the sip traffic and cannot register the SIP phone on the PBX where it reside on the cloud. Office 2 works perfect and has no issues with SIP phones. We have mikrotik routers in both locations. We created IPS...

ganewbie

Thanks for the help,
Now I believe that the SSTP is still needed, Is that correct?
Does anybody have an example?
Thanks in advance,

ganewbie

Setup the VPN works good site 1 and 2 are connected LAN to LAN
Now the question is how to force one computer in site 1 to appear as if it connected in site 2 and take the public IP of site 2?
The rest of the traffic in site 1 will go to internet as usual outside of the tunnel.
Thanks,

ganewbie

A good manual in my eyes, needs pictures of examples made via CLI and GUI "Both"
Otherwise the topic is tough to follow.

ganewbie

mrz wrote:LAC/LNS is currently unsupported.

Well, thanks for the update.
But do you have plans?

ganewbie

That is the setup for Cisco 7200 for the LNS function.
Is that setup possible on Mikrotik today? just for the LNS function not LAC as LAC has been done by Telco.

ganewbie

Sorry, we do not have data to share as we did not capture any but we had issues with our clients running SIP applications too. Our PBX works normal for clients not served from Mikrotik router. But client served from Mikrotik router after upgrade to 6.25 they do not have outbound any more. What we fo...

ganewbie

RB750 firmware 6.18

The MLPPP seems to work however we have only 2 symmetric lines, when bonding if you go to the status it shows that the active links 4, 5, 6 any number.
What is the reason for this or does anyone else see this behavior?

Thanks,

ganewbie

Hi hedele,
Thanks for the quick answer. In our case there is authentication but only password (no username).
Is is basically terminating PPPoE sessions for DSL clients on L2TP tunnels. It looks like this might not work then.
Thanks again,

ganewbie

Hi hedele,
Are you sure? Do you use Mikrotik as LNS in production? if yes, what is the max number of sessions that you could run?
Anybody else doing this?
We are interested only on the LNS side so it could be a good news for us.
Thanks

ganewbie

Same thing happened to me but on RB951.
Net install fixed it after I thought it was gone.

ganewbie

L2TP is often used by ISPs when internet service for example ADSL is being resold. From the end user, packets travel over a wholesale network service provider's network to a server called a Broadband Remote Access Server (BRAS), a protocol converter and router combined. On legacy networks the path f...

ganewbie

Sounds like a good candidate for netinstall

ganewbie

Great that it worked for you but could post the instruction in order to benefit the community.

ganewbie

May be, I have asked the wrong question,
Simply, can I use CCR1036 with Radius server for ADSL service (PPPoE)
Client base is less than a 1000.
need the following:
netflow (determin the usage for each login credential)
Be able to asign static IP to certain clients

Thanks in advance,

ganewbie

Can CCR1036 replace ASR 1002 to work in ISP environment that support ADSL clients (PPPoE sessions) with Freeradius?
What are the Pros and Cons vs ASR !002 or Juniper?
Thanks,

ganewbie

Today I am an Internet Service provider that has nothing in terms of any equipment just a middle man where I sell private label internet service to end user. I would like to gradually build myself up. First thing I am thinking of having the end user in case of PPPoE to authinticate at my own office ...

ganewbie

Hello,
I am a virtual ISP (Internet Service Provider), need to add more capability such as have the clients to authenticate at my place and then direct them to the Actual ISP to start browsing.
How do I do this? What equipment do I need? Thanks.

Search found 46 matches