MikroTik

RB 1200
Traffic - 35MB
Version: 5.6 after 5.7 was drawn

The RouterBoard randomly reboot during the day. Even with lower traffic it restarts. Average temperature 55 degrees. And both have the same problem RouterBoard. I'm worried because I still have two more of them here. Saver if I would like to have more people having the same problem. And how to solve. I have already sent the file to the support. More time someone has already managed to solve the problem.


Thanks

Felipe R. Santos

Temperature
Temperature System Temperature CPU Cpu

Hi,

I also have this problem with two RB 600 Board.
Sporadic reboots are on the agenda.
One routerboard have the Version 5.6 and the other 5.7.

Franco

right now a RB 433 AH with RouterOS 5.6 has rebooted.
In the LOG you can see the follow message:

router was rebooted without proper shutdown (cause1)


with the Version 4.xx i never have this problems.
I hope MT FIX this problem.

Franco

Hello everyone.
My RB1200 has problems after a scheduled reboot (swicth off).
After the reboot, the ethernet LEDs number 1 (connected to a cisco router) are turned off. Controls "watchdog" and NetWatch containing scritp running reboot, have no effect.
Given the problems mentioned on this thread at this point I can not understand if the problem is hw or sw type. I do not know what to do. Change rb1200 with another router or wait for new firmware, or send my 1200 for repair hoping it's a hardware problem.

How did you solve this problem? Firmware latest. ROS 5.7 or a test build 5.8 and still have problems with reboot

more people from the Czech Republic has problems with spontaneous reboots. Devices are loaded around 80Mbit. Then there is a random restarts.

Hi there,

I own two RB1200 that just put them on production and they happen to have that problems. Every 5-30 minutes they reboot aleatory.

Just sent the support.rif to the vendor and to the Mikrotik support.



Jordi.

Any changes for rb1200 in routerboot 2.37 ?
We also have a problem with rebooting - Ticket#2011092166000416

Im testing firmware 2.37, and maybe OK.
See http://ispforum.cz/viewtopic.php?f=7&t=8033&start=75

Upgrade RouterBoot firmware to v2.37
http://routerboard.com/RB1200

Upload the firmware file to router and upgrade with command:
/system routerboard upgrade
Reboot router after this command is entered.

Please send us new supout file if you still experience rebooting on RB1200.

Hello everyone.
My RB1200 has problems after a scheduled reboot (swicth off).
After the reboot, the ethernet LEDs number 1 (connected to a cisco router) are turned off. Controls "watchdog" and NetWatch containing scritp running reboot, have no effect.
Given the problems mentioned on this thread at this point I can not understand if the problem is hw or sw type. I do not know what to do. Change rb1200 with another router or wait for new firmware, or send my 1200 for repair hoping it's a hardware problem.

I have had the EXACT same problem. It was every other day, now every other week. I was connected to a Cisco ASA on one side and Cisco router on the other. Some times both ports went dead. But I could get to the other ports. Upgrading from 5.2 to 5.6 seemed to reduce this occurrence, but it still happens.

Upgrade RouterBoot firmware to v2.37
http://routerboard.com/RB1200

Upload the firmware file to router and upgrade with command:
/system routerboard upgrade
Reboot router after this command is entered.

Please send us new supout file if you still experience rebooting on RB1200.

Sorry did not see this. I will do it.

routerboard: yes
model: 433UAH
serial-number: 1E44019DB2E6
current-firmware: 2.29
upgrade-firmware: 2.29

Same Problem reboot cause 1 every 2 hour aprox!!

routerOS 5.5

any idea?

The problem still exist . The board is rebooting one or two times a day
Rb1200 ros v 5.7 firmware 2.37

Lukas
RADIONET

the 433AHU
now is connected by jack a dc power supply 24V/1A
what happens if connect a POE and also let the current through the jack

be burned?
or work as DC BACKUP?

Sorry my poor English

The problem still exist . The board is rebooting one or two times a day
Rb1200 ros v 5.7 firmware 2.37

Lukas
RADIONET

what is in console?

The problem still exist . The board is rebooting one or two times a day
Rb1200 ros v 5.7 firmware 2.37

Lukas
RADIONET

what is in console?

router was rebooted without proper shutdown (cause1)

I upgraded to 5.8 and bios 2.37 but problem still exist .
Now the board is still rebooting but only once a week .
In the log : router was rebooted without proper shotdown (cause1)
Is the still problem with soft ?
Lukas
RADIONET

I'm having the same problem, anyone found a solution?

Have the same issue with RB1200, ~ once a week.
I upgraded my RB to latest OS and RouterBoot firmware, but now I can't see firmware version after kernel failure.

[admin@gw] >system routerboard print [admin@gw] >system routerboard settings print [admin@gw] >system package print

Hello Normis. RB1200 have procesor PPC 460GT-SUB600T it runs on 1000Mhz

But default frekvency for this chip is 667Mhz. It can be a source of problems?

Could you please check that Watchdog Timer on/off ?
Just go to System>Watchdog and uncheck the timer.

Best Regards,
Rigan.

The problem seems to have been solved by not using the door 9:10. I started using yesterday finally. The equipment was stopped.

http://forum.mikrotik.com/viewtopic.php ... 68#p292668


It seems it was resolved.

I wonder just how it is with the processor? Picture above

I wonder just how it is with the processor? Picture above

you think we changed the CPU with a software update? of course not, so your assumption is not correct. it was purely a software issue with the ethernet driver.

The cause of reboots is defined correctly ?
RB1200 - MD - eth1, eth2, eth3 - reboot
RB1200 - MD - eth0, eth10 - reboot
RB1200 - UA - eth0, eth10 - good

Ticket#2011112866000373
normis, can you please send me link to pre-release of 5.10, or say the date of the release ?

you think we changed the CPU with a software update?

NO, but PPC 460GT-SUB600T = default frekvency for this procesor chip is 667Mhz and your RB1200 have with this procesor chip default frekvency 1000Mhz.
It means that it is overclocked from production?

I updated our RB1200 to 5.10 pre.
After ~ 5 hours it rebooted about 10 times in 20 minutes.
Downgraded to 5.8.

As I mentioned early.
We have RB1200 with eth10 and it works perfect.
And we have RB1200 with eth0, eth1, eth2 - that works like this - restarts every day.

Did you sent supout.rif of 5.10 to support@mikrotik.com?

Did you sent supout.rif of 5.10 to support@mikrotik.com?

No send. Equipament in test Verson - 5.9 - 2.38

Did you sent supout.rif of 5.10 to support@mikrotik.com?

no, because it is a production RB.

version v5 is a night a pure nightmare better stay on 4.17 if not using nv2, don't hear what they try convince you its a total failure in stablilty

version v5 is a night a pure nightmare better stay on 4.17 if not using nv2, don't hear what they try convince you its a total failure in stablilty

beware new RBs are not downgraded as for RB433s fw 2.29 is very stable on high loades

version v5 is a night a pure nightmare better stay on 4.17 if not using nv2, don't hear what they try convince you its a total failure in stablilty

what makes you write such harsh baseless statements?

Dear,

i've an 1200, 5.9 frw 2.37, as ospf+mpls router, with all lan used, 2 times of day ospf stuck, if i disable an lan from neighbor router, ospf on 1200 goes up. when i log-in i see BEFORE of FULL->DOWN ethX down. ospf stuck.


any ideas?

Ps: neighbor router is an a rb1100 that work fine.


regards.

version v5 is a night a pure nightmare better stay on 4.17 if not using nv2, don't hear what they try convince you its a total failure in stablilty

what makes you write such harsh baseless statements?

Is there any chance of doing a recall on these MikroTik RB1200? In the equipment if there is a solution for it?

version v5 is a night a pure nightmare better stay on 4.17 if not using nv2, don't hear what they try convince you its a total failure in stablilty

what makes you write such harsh baseless statements?

Is there any chance of doing a recall on these MikroTik RB1200? In the equipment if there is a solution for it?

there is no hardware issue. software bug was fixed already, upgrade RouterOS to new version!

there is no hardware issue. software bug was fixed already, upgrade RouterOS to new version!

Normis,

I am having this same reboot issue with 711 boards, does this problem also include the 711's? If so what software version was supposed to fix it?

there is no "same" issue with RB711. if they are rebooting, it's because of some other issue. make a new topic or email support.

there is no "same" issue with RB711. if they are rebooting, it's because of some other issue. make a new topic or email support.

Thanks for reply,

I started a thread here the other day and it disappeared, but there is also one over in the wireless forum that Uldis responded to and I have also sent in several support files to Uldis but haven't heard anything back, I created another ticket tonight for it. Ticket#2011121566000092

I downgraded one of units I am having problems with to 5.6 with 2.36FW. No reboots yet but it hasn't been long enough to tell for sure.

Thanks,
Chadd

RB1200
ROS 5.8
I disabled IPSec(switched to SSTP) and now have uptime ~ 2d 21h without restarts.
It seems that my troubles were IPSec related(site-to-site IPSec with default encryption).

RB1200
ROS 5.8
I disabled IPSec(switched to SSTP) and now have uptime ~ 2d 21h without restarts.
It seems that my troubles were IPSec related(site-to-site IPSec with default encryption).

1. no, this had nothing to do with IPsec
2. THIS IS ALREADY FIXED IN v5.11 !!! Upgrade and there is no more issue on RB1200

Can confirm that 5.11 resolved my issue.
RB1200
Ports eth1, eth10
ROS 5.11
IPSec site-to-site
Uptime ~ 2 days.

Thank you.