I have tested and discovered that SFP-10G-LR SFP+ modules don't work with the CRS226 series switches.
Keefe
Re: SFP-10G-LR Doesn't work on CRS
Hello,
I am currently using a SFP-10G-LR in a CRS226, linked toward a CCR. This setup has worked fine the last 6-8months.
The SFP+ is a Fiberworks module, but is Cisco coded(was originally supposed to be used in a Catalyst 4500-e switch), but works fine with all Mikrotiks I have tested it with.
Regards
I am currently using a SFP-10G-LR in a CRS226, linked toward a CCR. This setup has worked fine the last 6-8months.
The SFP+ is a Fiberworks module, but is Cisco coded(was originally supposed to be used in a Catalyst 4500-e switch), but works fine with all Mikrotiks I have tested it with.
Regards
You do not have the required permissions to view the files attached to this post.
Re: SFP-10G-LR Doesn't work on CRS
Code: Select all
Please post printouts from commands:I have tested and discovered that SFP-10G-LR SFP+ modules don't work with the CRS226 series switches.
Keefe
Code: Select all
/interface ethernet print detail where name~"sfp"
and
/interface ethernet monitor (interface)
Re: SFP-10G-LR Doesn't work on CRS
Code: Select all
[admin@ehq-sw1] > /interface ethernet print detail where name~"sfp"
Flags: X - disabled, R - running, S - slave
0 S name="sfpplus1" default-name="sfp-sfpplus1" mtu=1500 l2mtu=1588 mac-address=4C:5E:0C:9B:C4:DE
orig-mac-address=4C:5E:0C:9B:C4:DE arp=enabled auto-negotiation=no
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off
rx-flow-control=off speed=10Gbps master-port=ether1 bandwidth=unlimited/unlimited switch=switch1
sfp-rate-select=high
1 S name="sfpplus2-gfs-xe" default-name="sfpplus2" mtu=1500 l2mtu=1588 mac-address=4C:5E:0C:9B:C4:DF
orig-mac-address=4C:5E:0C:9B:C4:DF arp=enabled auto-negotiation=yes
advertise=10M-half,10M-full,100M-half,100M-full,1000M-half,1000M-full full-duplex=yes tx-flow-control=off
rx-flow-control=off speed=10Gbps master-port=ether1 bandwidth=unlimited/unlimited switch=switch1
sfp-rate-select=high
[admin@ehq-sw1] > /interface ethernet monitor sfpplus2-gfs-xe
name: sfpplus2-gfs-xe
status: no-link
auto-negotiation: done
advertising:
link-partner-advertising:
sfp-module-present: yes
sfp-rx-lose: yes
sfp-tx-fault: no
sfp-connector-type: LC
sfp-link-length-9um: 10000m
sfp-vendor-name: OEM
sfp-vendor-part-number: SFP-10G-LR
sfp-vendor-revision: A
sfp-vendor-serial: CLS10281932
sfp-manufacturing-date: 14-01-10
sfp-wavelength: 1310nm
sfp-temperature: 44C
sfp-supply-voltage: 3.348V
sfp-tx-bias-current: 0mA
sfp-tx-power: -7dBm
Re: SFP-10G-LR Doesn't work on CRS
In printout we can see that module for some reason ain't receiving incoming signal from device that is connected on the other side. Printout from other device could probably show more. Also please mention what device model you have on the other side of link.
Who is online
Users browsing this forum: No registered users and 11 guests