How to access my remote device which is installed at ISP tower from winbox, installed as point to point connectivity.

Remote device Metal 5SHPn and Home Device SXT Lite5.

Use its ip and logon user and password.

Sent from Android by Tapatalk.

Dear jarda,


SXT Lite5 gateway IP is my Metal 5SHPn IP to access it or something else. need to ask ISP person to provide access.

Hard to understand. Try to clarify with your ISP.

Hard to understand. Try to clarify with your ISP.

Sir

i tried to contact my isp but they said its not possible for me to access my Metal 5SHpn from my home.
please guide me if there is any way to access my mikrotik device from home.....

Then you have the answer. If they set it in the way they blocked the access from your side, then it is so. Only negotiations with them can move you forward.

Anyway why you gave them metal if it should be obviously ptp connection? Two sxts in bridge would be much better. Building new connection with one side single chain and other side dual chain doesn't make sense for me. Do they use your ap for other clients?

Anyway why you gave them metal if it should be obviously ptp connection? Two sxts in bridge would be much better. Building new connection with one side single chain and other side dual chain doesn't make sense for me. Do they use your ap for other clients?

@ Jarda Sorry for late reply,
this what i want to know, using my AP for other clients. right now im getting too high pings pings request time out from my gateway.

It's more relationship problem than technical. If you have any kind of quality issues, you need to force your isp to solve it for you when they do not provide you what you are paying for. Technically you are out of the game if they refused to provide an access for you.

It's more relationship problem than technical. If you have any kind of quality issues, you need to force your isp to solve it for you when they do not provide you what you are paying for. Technically you are out of the game if they refused to provide an access for you.

One more thing im getting request time out from gateway often pings inconsistent 5ms to 80ms to 20ms. nothing downloading.
In online game i face too much lags and frame drop.

Use traceroute and continually ping all hops to see where the lag is added.

getting request time out and inconsistent pings on my gateway

@jarda,

If i want to give access to someone of my mikrotik Radio, what settings do i need in my mikrotik radio to access via browser (webfig login)

Do you mean administrative access? First of all you need to be able to reach the device by tcp protocol. Then you must not block port 80 in inbound chain. Www service has to listen on port 80. And have appropriate user /password.

So. Have you succeeded? Please do not use colors. Someone who uses black background cannot read it...

@jarda

yes success now i can access my Mikrotik remotely via webfig. Now you can also check my config if i did something wrong,

As per my isp he says for point to point connectivity consistent pings i need to replace my SXT Lite5.

Ok from now i avoid color text.

What's the distance between them? what kind of antenna are you using on the Metal 5SHPn? Are there more stations connected to the 5SHPn?

I can check it. Provide the address and user information via private message. You can also add an email to be able to send you my findings.

How your ptp link looks now and what you need to achieve?

@jarda,


im looking to get best latency consistent without fluctuations.

Still same result too much fluctuations using nstreme.

Why wds? Why not to update to newer version? What would happen if you use 802.11? What is the delay and at what throughput?

@jarda,


Never tried 802.11
when i select 802.11 on client side searching for network never connect.
what settings do you suggest for ISP side and client side?

You are still providing too few info about your situation...

If you have any account on skype or facebook or whatsapp or BBM let me know so that i can share all data ASAP


Right now AP= Metal5SHPN and Client=SXT Lite5
On SXT Lite

HT Tx Chains 1 Unchecked
HT Rx Chains 1 Unchecked

Skype is fine. Put your Skype nickname into private message to me here. I will write back.

@jarda,

PM not working..


Skype ID PM

Pm works. Received two from you.

First things first:

As Jarda recommended, please use latest RouterOS version.

http://download2.mikrotik.com/routeros/ ... 6.29.1.npk

Make sure you are using wireless-fp / wireless-cm2 package.
Upgrade firmware : " /system routerboard upgrade "

Please give us output of " /in wireless print advanced " CLI command. From both devices.

Check Fresnel zone.
Use Nv2 as it is more advanced protocol than Nstreme.
Measure interference in given area.
I suppose link have clear line of sight ?

Please post test results.

upgrading Metal 5shpn will factory reset.

First things first:

As Jarda recommended, please use latest RouterOS version.

http://download2.mikrotik.com/routeros/ ... 6.29.1.npk

Make sure you are using wireless-fp / wireless-cm2 package.
Upgrade firmware : " /system routerboard upgrade "

Please give us output of " /in wireless print advanced " CLI command. From both devices.

Check Fresnel zone.
Use Nv2 as it is more advanced protocol than Nstreme.
Measure interference in given area.
I suppose link have clear line of sight ?

Please post test results.

======================================================
====================CLIENT============================
[admin@MikroTik] > /in wireless print advanced
Flags: X - disabled, R - running
0 R name="wlan1-gateway" mtu=1500 mac-address=D4:CA:XX:XX:XX:XX arp=enabled
disable-running-check=no interface-type=Atheros AR9300
radio-name="D4CAXXXXXXXX" mode=station-bridge ssid="space.anoop"
area="" frequency-mode=manual-txpower country=australia antenna-gain=0
frequency=5700 band=5ghz-a/n channel-width=20/40mhz-ht-above
scan-list=default wireless-protocol=any rate-set=default
supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,
54Mbps
basic-rates-a/g=6Mbps max-station-count=2007 distance=dynamic
tx-power-mode=default noise-floor-threshold=default
nv2-noise-floor-offset=default periodic-calibration=default
periodic-calibration-interval=60 dfs-mode=none wds-mode=disabled
wds-default-bridge=none wds-default-cost=100 wds-cost-range=50-150
wds-ignore-ssid=no update-stats-interval=disabled bridge-mode=enabled
default-authentication=yes default-forwarding=yes default-ap-tx-limit=0
default-client-tx-limit=0 proprietary-extensions=post-2.9.25
wmm-support=disabled hide-ssid=no security-profile=default
disconnect-timeout=3s on-fail-retry-time=100ms preamble-mode=both
compression=no allow-sharedkey=no
station-bridge-clone-mac=00:00:00:00:00:00 ht-ampdu-priorities=0
ht-guard-interval=any
ht-supported-mcs=mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7,mcs-8,
mcs-9,mcs-10,mcs-11,mcs-12,mcs-13,mcs-14,mcs-15,mcs-16,mcs-17,
mcs-18,mcs-19,mcs-20,mcs-21,mcs-22,mcs-23
ht-basic-mcs=mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7
ht-txchains=0 ht-rxchains=0 ht-amsdu-limit=8192 ht-amsdu-threshold=8192
tdma-period-size=2 nv2-queue-count=2 nv2-qos=default nv2-cell-radius=30
nv2-security=disabled nv2-preshared-key="" hw-retries=7
frame-lifetime=0 adaptive-noise-immunity=none
hw-fragmentation-threshold=disabled hw-protection-mode=none
hw-protection-threshold=0 frequency-offset=0 rate-selection=advanced
multicast-helper=default multicast-buffering=enabled

[admin@MikroTik] >
========================================
=================AP=====================

[admin@space.anoop] > /in wireless print advanced
Flags: X - disabled, R - running
0 R name="wlan1" mtu=1500 mac-address=00:0C:XX:XX:XX:XX arp=enabled
disable-running-check=no interface-type=Atheros 11N radio-name="000CXXXXXXXX"
mode=ap-bridge ssid="space.anoop" area="" frequency-mode=manual-txpower
country=australia antenna-gain=0 frequency=5580 band=5ghz-a/n
channel-width=20/40mhz-ht-above scan-list=default wireless-protocol=any
rate-set=default
supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps
basic-rates-a/g=6Mbps max-station-count=2007 distance=dynamic
tx-power-mode=default noise-floor-threshold=default
nv2-noise-floor-offset=default periodic-calibration=default
periodic-calibration-interval=60 dfs-mode=none wds-mode=dynamic
wds-default-bridge=bridge1 wds-default-cost=100 wds-cost-range=50-150
wds-ignore-ssid=no update-stats-interval=disabled bridge-mode=enabled
default-authentication=no default-forwarding=no default-ap-tx-limit=0
default-client-tx-limit=0 proprietary-extensions=post-2.9.25
wmm-support=disabled hide-ssid=yes security-profile=default
disconnect-timeout=3s on-fail-retry-time=100ms preamble-mode=both
compression=no allow-sharedkey=no station-bridge-clone-mac=00:00:00:00:00:00
ht-ampdu-priorities=0 ht-guard-interval=any
ht-supported-mcs=mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7,mcs-8,mcs-9,mcs-
10,mcs-11,mcs-12,mcs-13,mcs-14,mcs-15,mcs-16,mcs-17,mcs-18,mcs-19,mcs-
20,mcs-21,mcs-22,mcs-23
ht-basic-mcs=mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7 ht-txchains=0
ht-rxchains=0 ht-amsdu-limit=8192 ht-amsdu-threshold=8192 tdma-period-size=2
nv2-queue-count=2 nv2-qos=default nv2-cell-radius=10 nv2-security=disabled
nv2-preshared-key="" hw-retries=7 frame-lifetime=0 adaptive-noise-immunity=none
hw-fragmentation-threshold=disabled hw-protection-mode=none
hw-protection-threshold=0 frequency-offset=0 rate-selection=advanced
multicast-helper=full
[admin@space.anoop] >

I see that you still haven't enabled wireless-fp / wireless-cm2 package.

Why do you use station-bridge as I see it's not slaved by bridge, better use station. Use nv2 instead of any.

So what are latency and throughput after that ?
Please post [ /interface wireless monitor 0 ] from station.

If there is clean line of sight, SNR > 50, no interference, good Fresnel zone, good adjustment - everything should work great.

I see that you still haven't enabled wireless-fp / wireless-cm2 package.

Why do you use station-bridge as I see it's not slaved by bridge, better use station. Use nv2 instead of any.

So what are latency and throughput after that ?
Please post [ /interface wireless monitor 0 ] from station.

If there is clean line of sight, SNR > 50, no interference, good Fresnel zone, good adjustment - everything should work great.

When i select (Client SXT Lite5) STATION mode keep on searching never connect to AP(Metal 5ShPn)

Then interface must be in L2 bridging. My apologies.

So what are results ?

I see that you still haven't enabled wireless-fp / wireless-cm2 package.

Why do you use station-bridge as I see it's not slaved by bridge, better use station. Use nv2 instead of any.

So what are latency and throughput after that ?
Please post [ /interface wireless monitor 0 ] from station.

If there is clean line of sight, SNR > 50, no interference, good Fresnel zone, good adjustment - everything should work great.

When i select (Client SXT Lite5) STATION mode keep on searching never connect to AP(Metal 5ShPn)

Yes clear line of sight
======Wireless-fp---nv2====== Client==================================
[admin@MikroTik] > /in wireless print advanced
Flags: X - disabled, R - running
0 R name="wlan1-gateway" mtu=1500 mac-address=D4:CA:XX:XX:XX:XX arp=enabled disable-running-check=no
interface-type=Atheros AR9300 radio-name="D4CAXXXXXXXX" mode=station-bridge ssid="space.anoop"
area="" frequency-mode=manual-txpower country=australia antenna-gain=0 frequency=5580 band=5ghz-a/n
channel-width=20/40mhz-eC scan-list=default wireless-protocol=any rate-set=default
supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps basic-rates-a/g=6Mbps
max-station-count=2007 distance=dynamic tx-power-mode=default noise-floor-threshold=default
nv2-noise-floor-offset=default dfs-mode=none vlan-mode=no-tag vlan-id=1 wds-mode=disabled
wds-default-bridge=none wds-default-cost=100 wds-cost-range=50-150 wds-ignore-ssid=no
update-stats-interval=disabled bridge-mode=enabled default-authentication=yes
default-forwarding=yes default-ap-tx-limit=0 default-client-tx-limit=0
proprietary-extensions=post-2.9.25 wmm-support=disabled hide-ssid=no security-profile=default
disconnect-timeout=3s on-fail-retry-time=100ms preamble-mode=both compression=no allow-sharedkey=no
station-bridge-clone-mac=00:00:00:00:00:00 ampdu-priorities=0 guard-interval=any
ht-supported-mcs=mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7,mcs-8,mcs-9,mcs-10,mcs-11,mcs-12,
mcs-13,mcs-14,mcs-15,mcs-16,mcs-17,mcs-18,mcs-19,mcs-20,mcs-21,mcs-22,mcs-23
ht-basic-mcs=mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7 tx-chains=0 rx-chains=0
amsdu-limit=8192 amsdu-threshold=8192 tdma-period-size=2 nv2-queue-count=2 nv2-qos=default
nv2-cell-radius=30 nv2-security=disabled nv2-preshared-key="" hw-retries=7 frame-lifetime=0
adaptive-noise-immunity=none hw-fragmentation-threshold=disabled hw-protection-mode=none
hw-protection-threshold=0 frequency-offset=0 rate-selection=advanced multicast-helper=default
multicast-buffering=enabled keepalive-frames=enabled
[admin@MikroTik] >
==========================