Tue Apr 29, 2014 12:12 am
There will be a few changes to the config above. Let me write it for you and I will paste it here as an edit.
Ryan
EDIT Configuration added Below.
Here is the config I have found some of and written the rest of for you. I have syntax checked it the best I can without having the relevant hardware to run it on as such you may have some spelling errors. This config also assumes you are using dual polarity capable cards/boards as it has the ht-tx and ht-rx chains set for 0 and 1 and is also using NV2.
Router A
/ip address add address=192.168.0.1/24 interface=ether1
/ip address add address=192.168.10.1/29 interface=ether2
/ip address add address=192.168.20.1/29 interface=ether3
/routing ospf network add network=192.168.10.0/29 area=backbone
/routing ospf network add network=192.168.20.0/29 area=backbone
/routing ospf interface add interface=ether2 cost=100
Router B
/ip address add address=192.168.1.1/24 interface=ether1
/ip address add address=192.168.10.2/29 interface=ether2
/ip address add address=192.168.20.2/29 interface=ether3
/routing ospf network add network=192.168.10.0/29 area=backbone
/routing ospf network add network=192.168.20.0/29 area=backbone
/routing ospf interface add interface=ether3 cost=100
Radio Link A
Radio 1
/interface bridge add
/int bridge port add interface=ether1 bridge=bridge1
/int bridge port add interface=wlan1 bridge=bridge1
/ip address add address=192.168.10.3/29 interface=bridge1
/ip route add gateway 192.168.10.1
/int wireless
set [ find default-name=wlan1 ] band=5ghz-a/n channel-width=20mhz disabled=no frequency=5745 l2mtu=1600 mode=bridge rx-chains=0,1 ssid=LinkA tx-chains=0,1 wireless-protocol=nv2
Radio 2
/interface bridge add
/int bridge port add interface=ether1 bridge=bridge1
/int bridge port add interface=wlan1 bridge=bridge1
/ip address add address=192.168.10.4/29 interface=bridge1
/ip route add gateway 192.168.10.1
/int wireless
set [ find default-name=wlan1 ] band=5ghz-a/n channel-width=20mhz disabled=no frequency=5745 l2mtu=1600 mode=station-bridge rx-chains=0,1 ssid=LinkA tx-chains=0,1 wireless-protocol=nv2
Radio Link B
Radio 1
/interface bridge add
/int bridge port add interface=ether1 bridge=bridge1
/int bridge port add interface=wlan1 bridge=bridge1
/ip address add address=192.168.20.3/29 interface=bridge1
/ip route add gateway 192.168.20.1
/int wireless
set [ find default-name=wlan1 ] band=5ghz-a/n channel-width=20mhz disabled=no frequency=5825 l2mtu=1600 mode=bridge rx-chains=0,1 ssid=LinkB tx-chains=0,1 wireless-protocol=nv2
Radio 2
/interface bridge add
/int bridge port add interface=ether1 bridge=bridge1
/int bridge port add interface=wlan1 bridge=bridge1
/ip address add address=192.168.20.4/29 interface=bridge1
/ip route add gateway 192.168.20.1
/int wireless
set [ find default-name=wlan1 ] band=5ghz-a/n channel-width=20mhz disabled=no frequency=5825 l2mtu=1600 mode=station-bridge rx-chains=0,1 ssid=LinkB tx-chains=0,1 wireless-protocol=nv2