Community discussions

MikroTik App
 
planetcaravan
Member Candidate
Member Candidate
Topic Author
Posts: 267
Joined: Tue Aug 25, 2009 5:33 pm

Can't access to an open network

Fri Jun 20, 2014 9:27 pm

Hi there,

I'm using a RB Metal 2SHPn with a 15db sector in outdoor.
This is an hotspot system with RouterOS 6.15 with latest firmware.
Other hotspot can see my ssid, my hotspot can see other hotspots but no terminal can't see my hotspot.

Here is my config
/interface wireless
set [ find default-name=wlan1 ] adaptive-noise-immunity=none allow-sharedkey=no antenna-gain=0 area="" arp=enabled band=2ghz-onlyn basic-rates-a/g=6Mbps basic-rates-b=\
    1Mbps bridge-mode=enabled channel-width=20mhz compression=no country=italy default-ap-tx-limit=0 default-authentication=yes default-client-tx-limit=0 \
    default-forwarding=no dfs-mode=radar-detect disable-running-check=no disabled=no disconnect-timeout=3s distance=dynamic frame-lifetime=0 frequency=auto \
    frequency-mode=manual-txpower frequency-offset=0 hide-ssid=no ht-ampdu-priorities=0 ht-amsdu-limit=8192 ht-amsdu-threshold=8192 ht-basic-mcs=\
    mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7 ht-guard-interval=any ht-rxchains=0 ht-supported-mcs=\
    mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7,mcs-8,mcs-9,mcs-10,mcs-11,mcs-12,mcs-13,mcs-14,mcs-15,mcs-16,mcs-17,mcs-18,mcs-19,mcs-20,mcs-21,mcs-22,mcs-23 \
    ht-txchains=0 hw-fragmentation-threshold=disabled hw-protection-mode=none hw-protection-threshold=0 hw-retries=15 interworking-profile=disabled l2mtu=2290 \
    mac-address=D4:CA:6D:62:C9:C1 max-station-count=50 mode=ap-bridge mtu=1500 multicast-buffering=enabled multicast-helper=default name=wlan1 noise-floor-threshold=\
    default nv2-cell-radius=30 nv2-noise-floor-offset=default nv2-preshared-key="" nv2-qos=default nv2-queue-count=2 nv2-security=disabled on-fail-retry-time=100ms \
    periodic-calibration=default periodic-calibration-interval=60 preamble-mode=both proprietary-extensions=post-2.9.25 radio-name=hotspot rate-selection=advanced \
    rate-set=default scan-list=default security-profile=default ssid=Hotspot station-bridge-clone-mac=00:00:00:00:00:00 supported-rates-a/g=\
    6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps tdma-period-size=2 tx-power=17 tx-power-mode=all-rates-fixed \
    update-stats-interval=disabled wds-cost-range=50-150 wds-default-bridge=bridge2-hotspot wds-default-cost=100 wds-ignore-ssid=no wds-mode=dynamic wireless-protocol=\
    unspecified wmm-support=disabled
/interface wireless manual-tx-power-table
set wlan1 manual-tx-powers="1Mbps:17,2Mbps:17,5.5Mbps:17,11Mbps:17,6Mbps:17,9Mbps:17,12Mbps:17,18Mbps:17,24Mbps:17,36Mbps:17,48Mbps:17,54Mbps:17,HT20-0:17,HT20-1:17,HT20\
    -2:17,HT20-3:17,HT20-4:17,HT20-5:17,HT20-6:17,HT20-7:17,HT40-0:17,HT40-1:17,HT40-2:17,HT40-3:17,HT40-4:17,HT40-5:17,HT40-6:17,HT40-7:17"

What could be my problem?
 
User avatar
rextended
Forum Guru
Forum Guru
Posts: 12007
Joined: Tue Feb 25, 2014 12:49 pm
Location: Italy
Contact:

Re: Can't access to an open network

Fri Jun 20, 2014 9:47 pm

It's very wrong choice run hotspot on band=2ghz-onlyn only N mode.

la stampante è solo "N"?

dfs-mode=radar-detect
radar a 2ghz?

hw-retries=15
quest è meglio metterlo a 7

ssid=Hotspot
per compatibilità con quei troiai di Apple device, set it to HOTSPOT

usi il wds?
bridge-mode=enabled
disattiva il bridge o rischi di creare loop...

wds-mode=dynamic
meglio se dynamic-mesh

wireless-protocol=unspecified
mettilo a 802.11

Who is online

Users browsing this forum: Bing [Bot], unhuzpt and 62 guests