Community discussions

MikroTik App
 
brainy
Member Candidate
Member Candidate
Topic Author
Posts: 155
Joined: Fri Sep 29, 2006 3:08 pm
Location: Unterschleissheim, Germany
Contact:

Different signal strenght rx/tx with dual chain

Thu Mar 22, 2012 11:54 am

Hi there,

someone has an idea what is causing this strange signal strengt?

LOS is ok, distance is ~250m One side is SXT, one side is OmniTIK (screenshot was made on the OmniTIK side) Both sides using "card-rates" with power set to 20 to prevent a too strong signal.

Regards,
Joerg
You do not have the required permissions to view the files attached to this post.
 
rodolfo
Long time Member
Long time Member
Posts: 553
Joined: Sat Jul 05, 2008 11:50 am

Re: Different signal strenght rx/tx with dual chain

Thu Mar 22, 2012 12:45 pm

could be:
1. a different propagation from H to V
2. something in radio/pigtail/calbe/antenna

you could discriminate from this two cases, polarizing antennas at 45°. If is the cause 1 the difference must fall near 0.

(remember: some sxt seems to have a problem in chain 1)
 
MrBoni
just joined
Posts: 10
Joined: Mon Mar 05, 2012 12:10 am

Re: Different signal strenght rx/tx with dual chain

Thu Mar 22, 2012 7:21 pm

@brainy I have the same problem. Same setup - OmniTik on one side, SXTs (and 711s) on the other. Also, same as me, you have different CCQ levels on Tx and Rx (97% vs 44%).

Don't know about you, but I'm not getting any more throughput if I enable chain1 on SXTs. It's like 2x2 MIMO isn't doing it for me.

If anybody has an idea, don't be shy to share it with us :)


My thread is here: viewtopic.php?f=7&t=60325
Still no reply.
 
User avatar
czolo
Member
Member
Posts: 423
Joined: Fri Mar 04, 2005 9:49 am
Location: Poland (Warsaw)
Contact:

Re: Different signal strenght rx/tx with dual chain

Thu Mar 22, 2012 10:12 pm

@brainy I have the same problem. Same setup - OmniTik on one side, SXTs (and 711s) on the other. Also, same as me, you have different CCQ levels on Tx and Rx (97% vs 44%).

Don't know about you, but I'm not getting any more throughput if I enable chain1 on SXTs. It's like 2x2 MIMO isn't doing it for me.

If anybody has an idea, don't be shy to share it with us :)


My thread is here: viewtopic.php?f=7&t=60325
Still no reply.
Maybe it's stupid - but try to rotate the SXT for 90 deg.
 
rodolfo
Long time Member
Long time Member
Posts: 553
Joined: Sat Jul 05, 2008 11:50 am

Re: Different signal strenght rx/tx with dual chain

Fri Mar 23, 2012 2:42 pm

@MrBoni

your problem (ccq) is very different from brainy (dbm)
in your case could be an interference problem
 
MrBoni
just joined
Posts: 10
Joined: Mon Mar 05, 2012 12:10 am

Re: Different signal strenght rx/tx with dual chain

Fri Mar 23, 2012 9:10 pm

@MrBoni

your problem (ccq) is very different from brainy (dbm)
in your case could be an interference problem
I have both low CCQ and different Tx/Rx signals levels!
Why do I have interference? I tried to change the frequency multiple times with no result.
Maybe it's stupid - but try to rotate the SXT for 90 deg.
I'll try that. But, if I may ask, why would that make any difference if both devices (OmniTik and SXT) are dual polarized?
 
DynStatic
Frequent Visitor
Frequent Visitor
Posts: 92
Joined: Thu Feb 18, 2010 3:11 am

Different signal strenght rx/tx with dual chain

Sat Mar 24, 2012 4:07 am

@MrBoni

your problem (ccq) is very different from brainy (dbm)
in your case could be an interference problem
I have both low CCQ and different Tx/Rx signals levels!
Why do I have interference? I tried to change the frequency multiple times with no result.
Maybe it's stupid - but try to rotate the SXT for 90 deg.
I'll try that. But, if I may ask, why would that make any difference if both devices (OmniTik and SXT) are dual polarized?
It won't make a difference if it's dual pol, however if happens after turning it 90 degrees you've ruled out a hardware problem. You can have interference on only one of the poles from a device that's single pole.
 
lazerusrm
Member Candidate
Member Candidate
Posts: 162
Joined: Sat Jan 29, 2011 7:56 am

Re: Different signal strenght rx/tx with dual chain

Tue Mar 27, 2012 7:08 am

As Above,

Interference can play a large role when you have significant Signal strength variations chain to chain. Interference / Multipath reflections can also cause problems here.


Run a spectral scan, then try out several different channels, and if you notice that the previously low signal chain gets higher signal levels on a different channel, then you have most likely

some interference.

Who is online

Users browsing this forum: lmeira, popecix and 20 guests