I really hope that the card does not consume 22W of power (without attachments) - that would be way to much.

Thanks for your replies. See the VLAN link in my signature. I've implemented it with great success in my environments. That's a pretty cool summary/guide, it gave a me a whole new perspective for my network architecture. Based on that i decided to move the CRS326 to the top, so it is directly attach...

Hello, i want to replace a CRS125 with a CRS326 and switch from bridge-based vlans to vlan switching over the switch chip, so that hardware offloading does work for all vlans. i read in the wiki how this can be done with the crs326, but i am not sure if my planned setup is possible with only using o...

Hi, i have a dual-wan-failover setup here - one uplink is common cable internet, the other one is a SXT LTE Kit from Mikrotik. My cellular provider does not provide public IP addresses for LTE users and uses carrier grade NAT, which is bad. I just want the possibility to access my network in case of...

Fixed by setting datapath to the same bridge as the local network, using tag with VID. the real problem was a typo in the default route for the vlan, fixed that, too.

Hi there, i have some problems with adding a wireless network for guests to my network setup, which manages the wireless aps via capsman. The CAPSman manager switch has a direct connection to the OPNSense Firewall with one 10 Gbit/s cable. So, i want to add the guest network separated by VLAN from m...

thanks for your reply. somewhere on the forum i read that the interface which is used for passthrough on the mikrotik device claims all packets from the mac address which is used for passthrough. Unfortunately i can't find this post again. That's why i tried to assign a different mac address to the ...

Hello, i have a problem with a SXT LTE Kit regarding LTE-Passthrough and concurrent management of the device. The SXT LTE Kit is directly attached with one 100m cable to an OPNSense (FreeBSD-based) firewall server, and provides via multi-wan a fallback connection in case of a failed DSL connection. ...

Oh yeah, i would need some of them
Or the CRS309-1G-8S+PC, there are no news, too.

Which RouterOS version do you have on both devices ? I have a WAP LTE Kit connected to an OPNSense firewall, which lost internet access after upgrading to RoS 6.43. After that, i did a downgrade back to 6.42.7 and the connection was back online. I think this change in 6.43 caused or is related to th...

I tried the same with two S+RJ10 modules per switch and found the following: 2x CRS317-24G-2S+ with 2x S+RJ10 both switches have a minimal configuration: bridge with all RJ45 and SFP Ports, HW Offloading, MTU = 9000 Switch1 is connected with Switch2 via SFP1 on both devices. Two workstations are con...

Hello, i have some problems with my 10 GbE network, which i can't properly analyze due some strange behavior of the mikrotik switches or the sfp modules. so, basically, my setup looks like this: Workstation (S+85DLC03DI via SFP to PCIe Card) <---- 30m 50/125 OM4 fibre cable ----> SFP1 (S+85DLC03DI) ...

Just a short and quick question, is there any timeline for the release of the new SXT LTE Kit as some other products from the MUM are already listed ? I am desperately in need of a better solution, currently i have a wap lte kit at a location, which barely has enough reception. the only available ba...

That is very strange, i think at least 1Gb has to work. While 35m may be too long for 10Gb, the lesser rates should work. Mikrotik states 30m as maximum length for a CAT6 cable, so a CAT5e cable is possibly worse. I just tried it with my setup after patching both Cat5e cables together (total length ...

Hello, hope my answer does not come too late. i have three CRS326 installed, one per floor, with six S+RJ10 modules. the cables between the floors are duplex CAT5e F/UTP with ~50m length, so i put one CRS326 on the first floor. cellar to first floor are now ~20m, first floor to second floor ~30m cab...

Hello,

yes i did a few tests. Everything fine so far, there are a few driver issues with Linux (you basically need to compile the driver from ubuntu 18.04 source), but the Windows machine is fine. Tested with 30m CAT.7 S/SFTP cable between CRS326 and Asus XG-C100C, 10 GBit/s up and running.

Got them today. Plugged into a CRS317-1G-16S+. What a shame. Shows link without a cable plugged in and lights go on and off. Auto Negotiation shows done/10Gbps. TX Counters increase. Seems to be a wireless card. SFP Info show 1m Copperlength and Wavelength 1280.00nm. SFP Info says the same here, TX...

Ordered some from mikrotik-store.eu, too. Received them today - after two days.

hello, i am quite new to router os and really fascinated by the possibilites provided by hard- and software. i have a network setup consisting of three crs125-24g-1rm at my office, connected to the internet through a pfsense appliance. further, there are a few cap lite for wifi. they are new, i repl...