From Lan1 IP 10.1.10.26 i can only Ping to LAN2 Gateway 10.1.10.125 From Lan2 IP 10.1.10.126 i can only ping to LAN1 Gateway 10.1.10.25 You have not introduced "Lan1" and "Lan2" with the above IPs. Are they distinct from "LAN1" and "LAN2"? If yes, what are their netmasks? Ie. 10.1.10.x you have not...

Hi guys i have a strange issue we have been recently assigned a Public IP /22 to our company , so BGP route is running all setup default BGP route, and we have peers working already. So we have created the filter rule to accept everything inside our /22 block on second mikrotik device we the followi...

Hi

once u boot into the switchOS

you will only be able to login via web interface on IP 192.168.88.1 or 192.168.88.2

so u have to setup a static ip on your pc NIC interface on the same range in order to be able to connect.

then u can upgrade it to switchOS 2.11 via the web interface

Hiya i had a similar issue, when i switched to SwOS and rebooted.. i lost access via winbox, i could only use the web interface page.. and the IP on the swOS did not changed to the configured one, i was able to access it using the 88.1 default ip, then on the system page configured back the IP from ...

Hi Guys

going further a litle bit on the configuration, this is a litle scenario diagram below..

i just need to trunk port BGP with specific VLAN, and PPPOE-SERVERS with another different vlan , but need the BGP to receive all vlans, not shure if this would be the correct configuration

Hi guys i have recently purchased one of this devices into our company for daily usage, but i am kind of lost with missing information about configuration.. i have setup switchOS firmware and booted on switchOS, upgraded it to version 2.11 switchOS, which is now running in switchOS mode only so i ha...

Hi guys quick question does anyone have this new RB4011 with SFP+ port running with PPPOE-server? i amd wondering what kind of maximum bandwidth speed you can reach with it lest say for a PPPOE-SERVER with around 400 to 500 users active maximum.. i am looking at the data specs and it states that for...

Hiya i would like to know if this exploit could affect the Mikrotik routers, its a exploit on the PPP daemon that has been wide open for the last 17 years CVE-2020-8597 Critical PPP Daemon Flaw Opens Most Linux Systems to Remote Hackers The US-CERT today issued advisory warning users of a new danger...

Sounds like an MTU issue, the default PPPoE server setup has an MTU of 1480. Its strange but doesnt sound like an mtu issue.. i thinks its something in the mangle , or mark-routing that its not accepting it to filter it correctly on Static LAN ips from another interface, tbh i am kind of lost now.....

Let's call CCR1009 (the ISP facing) R1. And let's call CCR1036 (the remote one) R2. The simplest case: if R1 and R2 are (more or less) completely independent from L3 (IP) point of view, then you could bridge two SFP interfaces on R1 (one currently used for WAN and one currently used to connect to R...

Well

thats exactly what i need i will give it a try, and will post the outcome result.

Again, it depends how the ISP route it. When they route the second /30 via the 1st, you can just set it on a link between your two routers and it will work. But when they route the second block just directly on the line (address2 via address1) you will need to use tricks. Hi yes indeed they use the...

Hi guys i have a small issue, and i am having hard times finding a working solution for .. My ISP service provider offers me 2 static IPs , split into 2 different blocks, meant to be used simultaneously on the same Mikrotik device. example Block 1 = 189.xxx.xx2.90/30 Block 2 = 201.xxx.xx9.124/30 Bot...

This was their response: Network IP *.*.135.188/30 Subnet Mask *.*.255.252 Host IP's *.*.135.189 & *.*.135.190 (Usable IP's) Broadcast *.*.135.191 Most likely a litle bit late for posting the outcome, but basicaly a /30 just means you have 2 IPs, one will be your gateway and the other will be your ...

Hi

Have a look at VRF/routing rules, with it you can setup independent routing for specific incoming interfaces.

Hi Sebastia thxs

i will do some research on it..


BTW forgot to ask before, can i use 2 different VLAN on one specific Interface on the Mikrotik without being bridge interface?

Hi guys I am having some issues forwarding 2 WAN Links via 1 specific interface using 2 Separate VLANs So i have 1 CCR where i have 2 Links input, each configure with separate Static IP and Gateway, on this specific CCR i have 2 PPPOE-Servers and i can forward traffic via IP profiles to each separat...

I just wanted to throw this in to the community for discussion. I operate a WISP in Spain who's client base consist of a large proportion of expats who use illegal UK IPTV services. We find ourselves having to pay for very expensive bandwidth,  that is not normally required, to keep these services ...

Hi guys, We sell IP transit to some smaller ISPs and also offer High Speed to residential clients and our current Router solution is reaching the limit, I would like to deploy a new Mikrotik Router for 40Gbps of traffic. I don't consider the CCR1072 because it only has 10Gbps ports and I'm consider...

Hi guys

i have a script that runs daily backups from the mikrotik RB

one of them died so i need to export the ppp user list and pppoe server configuration from the daily backup, to copy on a new RB ccr diferent model from the one that died, is this possible, if yes with what tools?

Hi Guys I have some doubts and i have searched on the forum for some specific information regarding my issue i have found some old posts with some vague information, or perhaps i dit not understand it fully. I will ask again is someone can point me on the right direction approach to what i am trying...

I can't see the photos but you have to run multiple up or tcp streams to use all codes. What way are you testing? Also the numbers you get are crazy good for this Cpu. Do you really mean Gbps? The Cpu only has 4 threads as Amd do not have hyperthreading until Ryzen, called SMT I think. Also this Cp...

Hi boys i have some doubts regarding the x86-64 architecture... but first things first, is it just me or there seems to have a bug on all versions of mikrotik x86 that cannot read RAM memory available correctly? or is it just some versions or Memory RAM modules that does not display it correctly? i ...

Hi guys Ok so i have decided to give it a try and test RouterOS 6.39.xx bugfix on a Spare machine i have here used in the past for bitcoin mining.. i wanted to check the troughput i could get out squeezing all the cpu cores.. PC specs: Amd Fx-4300 3.8ghz Am3 8mb Cache (4 Cores 8Threads) as we know M...