On AWS, after install container: 1) Stop EC2 (wait until it's stopped). 2) Using AWS CLI (one after the other): aws ec2 start-instances --instance-ids i-??? aws ec2 stop-instances --force --instance-ids i-??? * On console in Instance state, it will be showing Stopping. 3) Connect to CHR using your ...

I am happy to report that I did have an error in the Brocade config for vlan156 which enable "webauth" somehow. We are now 100% up and running with correct VLAN config! Thank you so much for your help, patience, and teachings @anav!

I'm 98% there! Thanks for all your help so far. I've added the bridge and removed PVID as you suggested. So get this. On the Brocade, all the VLANs work except for vlan156!! Vlan 172, 180, 190 when I plug in, I get a DHCP address, can ping the gateway, can get to the internet (when not blocked by fi...

@anav OK I configured as suggested. It took a few minutes to "set" so I was probably just impatient when I tested before. Almost there... I still have this loop issue. I had a (wifi) chromecast device that kept sneaking onto the VM DHCP (vlan172) which is crazy because 172 isn't even hangi...

Spoke too soon, I tried again, and I was able to get rid of `vlan156-Wifi` and just use the ether10S2 interface. So now the cap is configured as you suggested and the virtual wlans are working. So networking is looking good across subnets except now I have a loop.... - Loop Protect: `on` doesn't hel...

WEIRD! I saw another post of yours and made some changes and it's working for vlan156 wired/wifi/sfp! However, I think the CAP is still incorrect. Changed: - `vlan156-Brocade` was removed from sfp. - Added generic `vlan156` to `lanBridge` interface - Bridge Port: removed `vlan156-Brocade` and replac...

I messed around with the config a ton and eventually got RB4011 + CAP working for vlan156.

STILL BROKEN: vlan156 to Brocade and vlan190 to the CAP.

vlan172 is working just fine on Brocade....

Should I be doing `use tag` and setting VLAN ID (to 156) in the wlan interfaces? Or just needed in the bridge port vlan? But when I turned on vlan-filtering in the router (RB4011) I lose network access on both the Cap and Brocade. Ether ports 6-9 work. Something isn't correct with the trunking. - Sh...

Thanks @anav. Yes, vlan156 is the trusted/mgmnt. These are all my personal devices. I would be fine/happy the vlan156 was untagged (if that's easier) everywhere except going towards the Brocade over the sfp trunk but I don't know how this looks going to the CapAC. I might have noticed slow speeds on...

I seem to be struggling with the correct VLAN configuration for this network diagram. Can someone advise what is incorrect? The switch doesn't seem to be receiving the trunk traffic for vlan156 correctly. home_network (1).jpg RB4011 # aug/22/2022 20:38:33 by RouterOS 6.48.6 # software id = 8PQW-VGK7...

Just a heads up, I rebooted my ONT yesterday after 300 days of using this method and I could not authenticate. I then plugged my AT&T Gateway back in and it would not authenticate either after much power cycling troubleshooting. AT&T Advanced Support had to re-"push provisioning" (...

Thanks for this thread! I got mine working on my RB4011. @Paul I had issues being authenticated but no IP Address from DHCP as well. 1. Make sure Identity and Non-Identity in Dot1x are your Gatways MAC Address. 2. Set ether1 switch port to fallback AND the vlan-id=0 . Although...it seems that it wa...

Thanks for this thread! I got mine working on my RB4011. @Paul I had issues being authenticated but no IP Address from DHCP as well. 1. Make sure Identity and Anon-Identity in Dot1x are your Gatways MAC Address, with colons. 2. Set ether1 switch port to fallback AND the vlan-id=0 . Although...it see...

Similar to vsixnetworks, I'd like to know if using a RB260GS would be possible. My fiber run is too short to reach my rack. So the RB260GS would just act the dumb switch and 4011 would do all the work? Or would you need a CRS106?

For AT&T APN's you should use either: broadband, phone

wowsers! spent a long time on troubleshooting routing + timeout issues. Make sure on the AWS side (VPC > Routing Tables > [Your VPC]) that you are propagating the routes back to your router! Screen Shot 2019-06-21 at 3.06.20 PM.jpg Also, I updated the script for the dynamic routing config to support...

Following. I use the pseudo-bridge on AT&T gateway and max out at around 600. Would enjoy the full Gig....

1. Which LTE Category you are interested in most - CAT6, CAT7, CAT9, CAT11, CAT12, CAT16 or some other? The higher the better. Not necessarily for throughput but due to support latest 3GPP release. 2. Which LTE bands and which Carrier Aggregation combinations should be supported? Not sure. 3. Should...

Seems I had to reboot with the USB plugged in.

I just got a RB3011. First thing I did was upgrade to 6.40.5. I am not seeing any USB under Ports, only "serial0". However, when I plug in a USB 8GB flash drive it shows up under disks. What do I need to do? I need to be able to configure a USB 3G/4G modem (that I have working in my hAP AC).

I too wish there was a way to manage the Mikrotik wireless (from phone) to update the "Connect List" or adding security profiles. Unfortunately right now I have to hardwire into the ETH2, change manually. Only after Wlan Master is setup can I access the virtual WLan. This requires me to ha...