MikroTik

SirPrikol

3.34 not work too

SirPrikol

Not work on Windows XP

SirPrikol

/route bgp peer add hold-time=1m in-filter=home.nets.in instance=home.nets keepalive-time=5s name=peer1 out-filter=home.nets.out remote-address=::ffff:0.0.0.0 remote-as=65402 ttl=default Does not work. I want to connect from ANY ip and from a specific AS. Ideally, with any private AS, but this is n...

SirPrikol

Same Problem here. CCR1009 with Capsman "on" crash and reboot in loop without logging any Problem.

Confirm on CCR2004

SirPrikol

It is already built in. When you do an in-pace upgrade of a router running v6 the rules will be update to v7. It is advised to take a close look at them, though. Unfortunately, it does NOT work. Tested on several different devices I have not converted a single filter, and also not a single feast ha...

SirPrikol

In general, do you plan any BGP filter converter from the 6th version to the 7th? At least a separate software?

SirPrikol

Routing config cannot be upgraded if any other older v7 version was already installed previously. Config is converted only once. Yes, for the first time these devices were updated from 6.48.5 long-term to ROSv7.1 (testing), BGP parameters were not converted on any device, and also, when trying to r...

SirPrikol

Unfortunately, neither BGP settings nor filters are converted to ROSv7

SirPrikol

"Filters
Convert routing filters after upgrade from v6.x"

This is true? Has anyone tested it? Does it work exactly?
Otherwise, you don't really want to lose a lot of connections due to the curvature of the work

SirPrikol

+1

In addition to TAYGA, another software for nat64 was found on the Internet

https://www.jool.mx/en/index.html

SirPrikol

We are waiting for "synthetic" routes for / 32, / 25, etc

Advertise it from ip firewall address-list

SirPrikol

Return the display of the entire route table in the winbox. Sometimes you need to find what has arrived, but you don't know the prefix. It's easier to look at the full and see than to guess.

Especially relevant for fv tables ipv6

SirPrikol

Understand that we understand how and what should work, which prefix to allow for the entrance, which one to deny ... But at the same time dst == .... both at the entrance and at the exit ... This is the first thing that is misleading. Therefore, we ask that there is no confusion. In ROSv6 it was co...

SirPrikol

I will support ChaOs. It's better to do it through the GUI and make it clear. Otherwise, keep the rules of the quagga bird in your head and now even from mikrotik - this is already becoming a mess. Look for where you misspelled ... It's better then to sit on the 6th version of ROS and endure the lac...

SirPrikol

And these are all filters? Dear community, I propose to add to this topic all possible filter variations according to the new scheme from ROSv7. This will really help with the move. I am trying to convert all my filters to the new version. Faced a problem, I can not announce / 32 mask until I write ...

SirPrikol

Hello everyone, where are the promised BGP filters?
This is the only thing that stops me from moving to v7.

SirPrikol

For normal work with the billing system and IPv6, you need to enable either pppoe-pd or enable DHCPv6 server selection in the profile for pppoe (pptp, l2tp etc ..) Now it is possible to specify only the pool of ip addresses in the profile, but then the client arrives with dynamic dhcpv6 server and d...

SirPrikol

There is one problem, in this configuration, the script does NOT include back triggers. It is necessary or in scheduller automatically to include triggers in 2-3 minutes or to add in a script a parameter about inclusion of the trigger on number

SirPrikol

Good afternoon. There are 4 providers, are connected in RB3011, everything is configured, reservation and balancing. Everything works. There was a need through tool fetch receive the file, but only through a specific provider (or through a specific interface). All 4 have different physical connectio...

SirPrikol

Me too need this

SirPrikol

answer myself interface 00.01_pppoe-ISP1 - Dinamic IP over pppoe interface 00.02_pppoe-ISP2 - Dinamic IP over pppoe inteface BACKUP - static ip over ethernet - 198.51.100.254 /ip firewall mangle add action=mark-connection chain=input connection-state=new in-interface=00.01_pppoe-ISP1 new-connection-...

SirPrikol

Good afternoon. There are 2 providers. Tuned balancing channels, everything works. But they fall (not at the same time) decided to do the filo. With one provider mostly and the second as a backup, there are no problems, but with the two main ones, I can not understand the logic. 192.168.0.0 - ISP1 1...

SirPrikol

SirPrikol - Please generate supout files on your router and send them to support@mikrotik.com. Without additional information we can not determine what is the cause of the problem that you have.

send
[Ticket#2018041122002806]

SirPrikol

New bridge interface created with L2 65535 MTU. After then all local network down and cpu on all mikrotik routerboard is above 100%

SirPrikol

SirPrikol - Did you downgrade to 6.41 routes where working and upgrade to 6.41.1 and they are not working again? Can you provide supout file to support@mikrotik.com which would be generated while there are such routes on router;

Send
Ticket#2018020722003201

SirPrikol

Yes, I understand this, I just wanted to show the person that he is wrong and the mapping goes to winbox normal. And the fact that the seconds do not fit - it's just the problem of his system, not the winbox itself. I went through this when my wine did not update normally, and I had to reinstall it....

SirPrikol

After this update, static routes on Ipv6 stopped working. I had to return to the dynamic receipt of the address from the provider. Static pool stopped giving normally addresses and routes

SirPrikol

Да ну, секунды видны и на больших разрешениях Когда ты мне этот скриншот покажешь на винде, я соглашусь. https://d1ro8r1rbfn3jf.cloudfront.net/ms_39696/lgEb27dKTlJrV6LIQQDaoejgMFDVht/XP_Local%2B%2B2018-02-01%2B21-55-57.jpg?Expires=1517601375&Signature=KCHR8ysPmDgMWb6M4LwSNu2GNK-JP7g1m0i8cpHs4B8...

SirPrikol

Всё в норме. Смотри что у тебя с ситемой. Я под вайном на макбуке идеально вижу секунды Ты не в теме. Не влезают секунды у кого размер монитора большой типа 2560х1440 или азиатская раскладка шрифтов. p.s. почитай предыдущую тему. не я один жаловались. Да ну, секунды видны и на больших разрешениях h...

SirPrikol

Пару раз писал по английски.... не поняли ... напишу на великом и могучем... может его еще не забыли. https://c.radikal.ru/c18/1802/d7/b8b6c2bea09e.png У вас же было в бете 3.хх возможность изменять размеры полей в логе, потом убрали. Но обещали вернуть в финале и забыли. Ну ужели сложно сделать по...

SirPrikol

After a night of experiments it was clarified. If I do not take DHCPv6 from the provider by the client, and I register everything with pens (routes, addresses, etc) then everything works, static addresses remain. As soon as I take everything through DHCPv6, not one address remains. We need to wait f...

SirPrikol

Hi
I told, this all works before rebooting all devices at the same time due to a drop in electricity. If RB3011 just reboots, there are no problems, if all but the RB3011 are rebooted, there are no problems either. Problem with simultaneous reboot.

SirPrikol

Good afternoon. Tell me please. There are 6 mikrotik devices on the network. WAN RB3011 on it raised IPV6 DHCP server. After the fall of electricity, all 6 devices are started, but the addresses (IPv6) are received from RB3011 each time in different ways. How to make it hard to bind an IPV6 address ...

SirPrikol

Layer 7

^(\x13bittorrent protocol|azver\x01$|get /scrape\?info_hash=get /announce\?info_hash=|get /client/bitcomet/|GET /data\?fid=)|d1:ad2:id20:|\x08'7P\)[RP]

not work correctly
Mark only some packets

SirPrikol

in 6.40.4 p2p traffic not mark

p2p matcher is obsolete please use layer7 matcher instead

SirPrikol

Hello.
Two providers are connected with load balancing, everything works fine,
how to send torrent traffic to a certain provider?

SirPrikol

I think that the site does not work, because on other resources the check is normal. But there is another problem. I can not save static addresses in the dhcp server ipv6. They are reset after the link is broken. At the same time, they change on client devices. On previous versions, they were saved ...

SirPrikol

Hello.
In 6.40.4 just not work ipv6 normally.

All ping is fine, IPv6 sites work fine, but when i whant to test my connectivity on some sites (like ipv6-test.com) I have error.

On 6.40.3 works fine.

Search found 38 matches

Re: WinBox v3.33 and v3.34 released!

Re: WinBox v3.33 released!

Re: v6.48.6 [long-term] is released!

Re: v7.1 is released!

Re: v7.1 is released!

Re: v7.1 is released!

Re: v7.1 [testing] is released!

Re: v7.1 [testing] is released!

Re: v7.1 [testing] is released!

Re: Feature Request - NAT64/DNS64 CGN

Re: v7.1rc4 [development] is released!

Re: WinBox v3.31 released!

Re: Feedback on RouterOSv7 route filtering

Re: Feedback on RouterOSv7 route filtering

Re: Feedback on RouterOSv7 route filtering

Re: v7.1beta5 [development] is released!

Need pppoe-pd, or select DHCPv6 server in ppp profile

Re: Traffic monitor with Telegram report

Request in a script via a specific interface

Re: CloudFlare DNS over TLS

Re: Failover and 3 ISP

Failover and 3 ISP

Re: v6.41.4 [current]

Re: v6.41.4 [current]

Re: v6.41.1 [current]

Re: Winbox 3.12 released!

Re: v6.41.1 [current]

Re: Winbox 3.12 released!

Re: Winbox 3.12 released!

Re: Winbox 3.12 released!

Re: IPV6 DHCP Server

Re: IPV6 DHCP Server

IPV6 DHCP Server

Re: Torrent+Mikrotik ROS

Re: Torrent+Mikrotik ROS

Torrent+Mikrotik ROS

Re: v6.40.4 [current]

Re: v6.40.4 [current]