As a service provider with 500+mikortik routers in the network, we would love to have IS-IS for scalability

Script is triggered everytime a lease is bound, offered, busy, unbound etc.

No it's not, i've tried it.. It's only triggered on a bound event

Zerotier is definitely a wanted feature

Hi,

Sorry to dig up a slightly old thread, but can you rate limit on RB260GS?

I believe you can but reading this has put doubt in my mind!

Thanks

In current version of switchOS you can only set the egress rate on the ports, but it is possible

Normally on the LHG60s the SNMP OIDs are mode=.1.3.6.1.4.1.14988.1.1.1.8.1.2.1 ssid=".1.3.6.1.4.1.14988.1.1.1.8.1.3.1" frequency=.1.3.6.1.4.1.14988.1.1.1.8.1.6.1 However on this particular unit it is [admin@LHG60] > /interface w60g print oid Flags: X - disabled, R - running 0 R mode=.1.3.6...

HI, have you tried updating the RouterOS version ?

This is still an issue near the end of 2019.

I don't remember where this was in our topology so I can't go and find what I did to fix it But I do know that I don't ever use the PTMP network type anymore, and I exclusively use point-to-point so i'm guessing this is what I did with that link as well All multi-point links now use individual VLAN...

This looks like it's in the beta release changelog.. So it's a known bug, just have to wait until it's brought to stable or LTS

So it seems that l2mtu of a bridge gets set to smallest l2mtu value of all slave interfaces (OP should check the whole list of interfaces, from the screenshot it's not clear if the whole list is shown or it's actually truncated) and can not be set. And it's logical that MTU of bridge is set to smal...

At this point, just add the ports to the back of the switch. You'll get 96 10g ports + 6-12x 100g uplinks All in a 1U formfactor, then if you wanted to get fancy, i'm sure you could come up with a way to get 5 or even 6 port height in a combined 2U space. which would be up to 144 ports on the front ...

make sure there's nothing attached to the serial console if the device has one. the values next to serial should be low. if it is high and increasing rapidly, you have the same issue as we had. then you just need to disconnect the cable... Thanks for the answer, we don't have serial cables connecte...

I also had problems with DHCP using ROS 6.42.x. I updated to 6.43 and the problem was solved.

Regards.

My issue is that I cannot upgrade past 6.42.x without crippling these devices.

How do I change the MTU on my bridge on the CRS317?
Never had this issue before.
You can see every single interface has a higher MTU than the bridge interface which does not allow me to change manually..

We saw this on old 300 MHz RBs and sometimes on 400MHz RB411

This has happened on powerbox pros so far, and rb850gx2

Have you already tried to use netinstall to format and reinstall them to the current version with blank configuration, then re-configure them to your needs? Don't use backup/restore. At most do a /export first and then use that to re-configure them manually or by pasting sections of the /export tha...

I submitted this issue to support@mikrotik.com i think 3 times now, and have never heard back from them on the issue. After running a firmware update, in fact any firmware past 6.42.x causes multiple devices to lock up, and causes the DHCP server to not start, the CPU is at 100% and barely passes an...

CHR is indeed the only way forward for the forseeable future. However, you should be able to get 20(40) or so gbps out of your CCR1072, Number 1: how many nat connections do you have. Number 2: don't use masquerade anywhere. You're using fast track, correct? There are many small things that you can ...

Have this exact same problem, radius works everywhere, except where it doesn't(firewall rules, etc.) but how do we make the router send out a test request? Not without bringing out clients down to force them to redial PPPoE

1750m LHG60 ROS 6.43 lhg60 1750m.png Freq: 58320 -59 60480 -63 62640 -62 Dang! I think you won a certain type of silicon lottery! We have 750m link at ~-50dBm signal. Yours at 1km more should see an additional ~-22dBm fade over ours so expected would be -72. I wonder, if you found the magical beamf...

results Test with external tool or Traffic-generator and You will get full Wire speed I don't. 6.43rc64. Real world TCP/IP throughput is only 200-300mbps down, 200-300 up, tested using Iperf3 only over the link, and speedtest.net to 700mbps fed pop. Using udp test get around 600-700 download one wa...

Please help. Everyone is complaining about the internet never working. Export your configuration (pasting it between forum code tags) from this command: /export compact hide-sensitive file=MyFile.rsc The output will be under your "Files" option in the GUI. Here is an example config you sh...

get on bug fix, no issues at all on my side

Yeah, "upgraded" all the routers to 6.39.3 and still see this issue.

I am running 6.41 on all of the hAP units in an apartment complex. Devices that usually can connect to the 2.4 suddenly aren't able to. The problem is only fixed in one of 2 ways, 1. restart the router. 2. disable and re-enable the 2.4 interface. There is nothing else that brings back the ability fo...

I've got to say, Why not support an inherently better protocol? IS-IS, while bad in the middle east, is great in ISPs. The largest ISPs don't use OSPF for a reason, and BGP isn't going to improve on the tilera processors any time soon. At least not to the point that makes it usable with multiple pee...

I was able to resolve this issue.
Not exactly sure what caused it.
used an ftp client, as well as started the dude up with its files being stored on sd card instead of onboard.

Have tried my hardest to get MIBs imported to the dude, to no avail. For some reason it will absolutely not take anything at all. I have tried placing the files in 3 different places to force the dude to read/accept it, but it will show no where in the dude client even though it as been days and sev...