Community discussions

MUM Europe 2020

Search found 13 matches

by androx2k4
Thu Dec 14, 2017 4:29 pm
Forum: Wireless Networking
Topic: How to configure cAPlite in dhcp relay mode?
Replies: 5
Views: 580

Re: How to configure cAPlite in dhcp relay mode?

It should be done directly on your device, not via caps manager. Just bridge ether1 and wlan in your CAPlite
Ok, but this means that the cAP in bridge mode is not controlled by CapManager? I have to remove it from the CAPs lists?
In any case thank you so much!
by androx2k4
Thu Dec 14, 2017 12:17 pm
Forum: Wireless Networking
Topic: How to configure cAPlite in dhcp relay mode?
Replies: 5
Views: 580

Re: How to configure cAPlite in dhcp relay mode?

Hello, you do not need a dhcp relay, but your devices have to be configured in bridge mode, so they will get an ip from your main router.
The configuration in bridge mode where it should be done?
Because in the configuration settings, in the cap manager, the only avaliable mode is AP.
by androx2k4
Thu Dec 14, 2017 12:24 am
Forum: Wireless Networking
Topic: How to configure cAPlite in dhcp relay mode?
Replies: 5
Views: 580

How to configure cAPlite in dhcp relay mode?

Hi, it is a simple question but I'm stucked on it. I have a mikrotik router hEX and a cAPlite in my home. I already setup the CAPMAN connection (but it shouldn't be relevant). In my domestic home I have several wired and some wireless device. I would like to give both to the kind of devices (wired a...
by androx2k4
Fri Dec 01, 2017 5:39 pm
Forum: Beginner Basics
Topic: Help in proper nat inside multiple subnet
Replies: 21
Views: 1428

Re: Help in proper nat inside multiple subnet

I see your point. The main reason is that I was developing some code for IOT devices (what else in this moment :) ) and the code use a publicdomanindame.com:portnumber to connect the server .200:realportnumber for exchanging data. The idea is to move the IOT device in another location and they stil...
by androx2k4
Fri Dec 01, 2017 3:20 pm
Forum: Beginner Basics
Topic: Help in proper nat inside multiple subnet
Replies: 21
Views: 1428

Re: Help in proper nat inside multiple subnet

I cannot fully understand the point 2) because the AP-Wifi has two port: one is the WAN that it is fisically connected to the ethernet 3 of the mikrotik. The second port is the "Wifi" port that allow the connection to the router. For the two 3) is already done and for this reason the PCB gets an IP...
by androx2k4
Thu Nov 30, 2017 3:49 pm
Forum: Beginner Basics
Topic: Help in proper nat inside multiple subnet
Replies: 21
Views: 1428

Re: Help in proper nat inside multiple subnet

So there is no 192.168.8.0/24 address assigned to any of MikroTik ports. The only local address assigned on MikroTik I can see is: /ip address add address=192.168.1.1/24 interface=ether2 network=192.168.1.0 So, if you want to keep WiFi users separated (or at least most of them), I would do the foll...
by androx2k4
Thu Nov 30, 2017 2:59 pm
Forum: Beginner Basics
Topic: Help in proper nat inside multiple subnet
Replies: 21
Views: 1428

Re: Help in proper nat inside multiple subnet

I am lost again :) Now I start to think, that MikroTik is connected with a cable (ether3) to Router B on it's WAN. Am I right? What is the exact address of ether3 and WAN. Making a command /ip export hide-sensitive would help a bit. If the above is right, and the Router B is not connected to 192.16...
by androx2k4
Thu Nov 30, 2017 12:57 pm
Forum: Beginner Basics
Topic: Help in proper nat inside multiple subnet
Replies: 21
Views: 1428

Re: Help in proper nat inside multiple subnet

I don't think it is needed but in case I also put the miktorik eth1 in the DMZ of the Modem/router OMG, it's a total mess. So PC B is tripple NATed...! DMZ is necessary. More convenient would be to set up modem in a bridge mode and make PPPoE connection on MikroTik, so you will get the public IP di...
by androx2k4
Thu Nov 30, 2017 12:02 pm
Forum: Beginner Basics
Topic: Help in proper nat inside multiple subnet
Replies: 21
Views: 1428

Re: Help in proper nat inside multiple subnet

Immagine6.png
by androx2k4
Thu Nov 30, 2017 11:36 am
Forum: Beginner Basics
Topic: Help in proper nat inside multiple subnet
Replies: 21
Views: 1428

Re: Help in proper nat inside multiple subnet

Thank you for your time. (I can't see anymore the previous diagram posted but I repost an updated one). I apologies. I was thinking it was quite clear within the use of subnets address. It wasn't, and unfortunately it is still not. But in case here a more complete diagram The mikrotik has the eth1 c...
by androx2k4
Tue Nov 28, 2017 10:20 am
Forum: Beginner Basics
Topic: Help in proper nat inside multiple subnet
Replies: 21
Views: 1428

Re: Help in proper nat inside multiple subnet

I apologies. I was thinking it was quite clear within the use of subnets address. But in case here a more complete diagram The mikrotik has the eth1 configured in ppoe is connected to the VDSL modem (WAN) the eth2 is connected to a switch and server A and PC (and others) the eth 3 is connect to a wi...
by androx2k4
Mon Nov 27, 2017 4:59 pm
Forum: Beginner Basics
Topic: Help in proper nat inside multiple subnet
Replies: 21
Views: 1428

Re: Help in proper nat inside multiple subnet

Thank you. I read the page and I'll try it but in general I have some doubt. Infact I implemented exactly the two rules I wrote down in the diagram chain=srcnat action=masquerade out-interface=WAN chain=dstnat action=dst-nat to-addresses=192.168.1.200 to-ports=80 protocol=tcp dst-port=2226 log=no lo...
by androx2k4
Sun Nov 26, 2017 7:14 pm
Forum: Beginner Basics
Topic: Help in proper nat inside multiple subnet
Replies: 21
Views: 1428

Help in proper nat inside multiple subnet

Hi. I need to correctly forward a connection from a subnet to another one. In the same time the IP to be used must be the public one. In the diagram the configuration and the nat configuration I'm using. Immagine1.png If the PC A try to reach the SERVER A using the public domain name is correctly fo...