Community discussions

Search found 26 matches

by florid
Mon May 27, 2019 9:05 am
Forum: Forwarding Protocols
Topic: L2TP+ipsec speeds
Replies: 7
Views: 846

Re: L2TP+ipsec speeds

what's the recommendation then?
by florid
Wed May 22, 2019 7:02 am
Forum: Beginner Basics
Topic: Plex Media Server Remote Access - Port Forwarding
Replies: 15
Views: 1023

Re: Plex Media Server Remote Access - Port Forwarding

you can test port forwarding work or not by put a new system with the required port open. I experienced similar Plex Media Server Remote access flashing issue recently, and ends up with forgetting to allow the port on the Plex system itself (Synology DSM Firewall blocked it). RouterOS port forwardin...
by florid
Mon Feb 18, 2019 7:54 am
Forum: General
Topic: IP Cloud
Replies: 37
Views: 6904

Re: IP Cloud

I tested IPv6 once but that IPv6 address keeps in my IP Cloud record. How can I remove/clean that IPv6 entry only since I no longer use IPv6?

Update: Mikrotik support told me to disable / re-enable IP Cloud will remove no longer used IPv6 record.
by florid
Fri Feb 08, 2019 1:34 am
Forum: Announcements
Topic: Tik App, MikroTik android utility ALPHA test
Replies: 419
Views: 139820

Re: Tik App, MikroTik android utility ALPHA test

Is it possible to increase the request timeout limit?
I use this app to connect to a remote router in different country. It always disconnected with timeout message when pulling 'big' data such as view Log / Address list etc.
by florid
Thu Feb 07, 2019 1:21 am
Forum: Announcements
Topic: v6.43.11 [stable] is released!
Replies: 79
Views: 11161

Re: v6.43.11 [stable] is released!

Anyone noticed interface connectivity issue after upgrade? I have a remote HEX POE. No issue with the firmware upgrade. Rebooted twice and looks good. I can remote access the box via winbox without any issue. But after a third reboot, I noticed one interface to Synology NAS only has TX packet but ve...
by florid
Wed Jan 02, 2019 7:14 am
Forum: General
Topic: IPV6 DHCP client stuck on status "binding" after restarts
Replies: 2
Views: 289

Re: IPV6 DHCP client stuck on status "binding" after restarts

viewtopic.php?f=2&t=122420

i also submitted a ticket to support. Hope this can be fixed soon.
by florid
Thu Dec 27, 2018 5:13 pm
Forum: Wireless Networking
Topic: bulk disconnected, group key exchange timeout
Replies: 7
Views: 2149

Re: bulk disconnected, group key exchange timeout

Just experienced the same issue on 6.43.8
Hex Poe + ac AP.
by florid
Mon Dec 24, 2018 11:39 am
Forum: General
Topic: IPv6 PPPoE+DHCPv6 Client Pool Rebind BUG
Replies: 10
Views: 2169

Re: IPv6 PPPoE+DHCPv6 Client Pool Rebind BUG

This issue is still there on 6.43.8
by florid
Tue Nov 13, 2018 11:43 pm
Forum: General
Topic: Sonos across VLANs?
Replies: 13
Views: 4366

Re: Sonos across VLANs?

I recently implemented the same for Sonos by using igmp-proxy not PIM. Just need to add the interfaces into igmp-proxy and set which one is upstream, then apply the firewall rules for allowing UPnP traffic. That's it. According to Mikrotik Wiki igmp proxy is slightly lightweight than PIM, that's why...
by florid
Fri Oct 19, 2018 7:39 am
Forum: RouterOS v6 RC and v7 BETA
Topic: New IP cloud is coming.
Replies: 83
Views: 25262

Re: New IP cloud is coming.

Would be great if the IP cloud can expand the feature to whole configuration, something like Cloud Winbox. User can login the cloud portal to modify and customize the configuration, when the router box connects to Internet, automatically grab updated cloud configuration and deploy it. Two beauties: ...
by florid
Wed Sep 19, 2018 12:50 pm
Forum: Beginner Basics
Topic: Update package not properly downloaded and rebooted.
Replies: 2
Views: 260

Re: Update package not properly downloaded and rebooted.

Weird thing happened, the box came back online after 10 min still on 6.43 version.
by florid
Wed Sep 19, 2018 12:46 pm
Forum: Beginner Basics
Topic: Update package not properly downloaded and rebooted.
Replies: 2
Views: 260

Update package not properly downloaded and rebooted.

Hi, I have a remote hex poe. I tried to upgrade from 6.43 to 6.43.1. unfortunately, poor Internet speed, only download around 1MB file then timeout. But the upgrade process didn't do any check then reboot the box directly. Then it never back online again. What can I do next? Seems like a travel to t...
by florid
Mon Aug 27, 2018 8:27 am
Forum: Beginner Basics
Topic: Mikrotik VLANs (Office, Guest, Managment)
Replies: 10
Views: 1284

Re: Mikrotik VLANs (Office, Guest, Managment)

You can enable logging for the rules that you have created. Then you can see whether rules get hit.
You can also double check Dlink switch configuration. Maybe inter vlan traffic even not passing thru Mikrotik router.
by florid
Fri Jul 27, 2018 12:06 pm
Forum: Beginner Basics
Topic: Connecting three Cisco AP's to a Microtik
Replies: 6
Views: 847

Re: Connecting three Cisco AP's to a Microtik

Not really understand how you configure eth 6,7,8. Created multiple IP on the same interface as access port? That’s not trunk configuration on RouterOS I believe. Since you have Cisco wireless controller, you only need to configure WLC port to be trunk, all other AP port as access port. All the mult...
by florid
Fri Jul 27, 2018 2:48 am
Forum: Beginner Basics
Topic: Mikrotik 750G - Limiting my connection to a max of 90MBps
Replies: 9
Views: 879

Re: Mikrotik 750G - Limiting my connection to a max of 90MBps

Agree with Jotne, besides the Mikrotik router, is there any other device connects to ISP, like modem or media converter?
Maybe that modem LAN interface does not support 1G.
Or bad cable. Or fault Mikrotik port. Have you tried different Mikrotik port to connect to WAN?
by florid
Fri Jul 27, 2018 2:36 am
Forum: Beginner Basics
Topic: Connecting three Cisco AP's to a Microtik
Replies: 6
Views: 847

Re: Connecting three Cisco AP's to a Microtik

Not sure how you configure the bridge and vlans.
What about the IP firewall rules? Have you missed the outbound forwarding rule for AP vlans?
by florid
Thu Jul 26, 2018 11:55 am
Forum: Beginner Basics
Topic: add another TPLink router to mikrotik and allow accounting on different IP subclass
Replies: 3
Views: 864

Re: add another TPLink router to mikrotik and allow accounting on different IP subclass

thank you florid, i am beginner in mikrotik how do i go about doing it in WinBox? i got to IP -> Routes -> +New Route what do i fill-in for dst address, gateway, type, and several other options there? i'm using winbox 6.42.1. thank you very much for your kind attention. Dst Address: 192.168.8.0/24 ...
by florid
Thu Jul 26, 2018 2:11 am
Forum: Beginner Basics
Topic: VLAN segregation and bridge setting [SOLVED]
Replies: 15
Views: 1151

Re: VLAN segregation and bridge setting [SOLVED]

florid, on wich MikroTik have you got this configuration? i am using hex poe rb960pgs. The configuration is not exported from the device. But I drafted according to wiki page. I planned to have the experts check the configuration before implementing change to my router. Right now it is not necessar...
by florid
Wed Jul 25, 2018 2:37 am
Forum: Beginner Basics
Topic: VLAN segregation and bridge setting [SOLVED]
Replies: 15
Views: 1151

Re: VLAN segregation and bridge setting [SOLVED]

Thanks CZFan and xvo The reason I am looking for HW offloading is my two IP cams have constant traffic (15Mbps) from vlan80 to NAS (NAS only has one NIC and not support trunk interface) in vlan10. The Cams are physically installed outside of my house so I want to put them in a separated 'untrusted' ...
by florid
Tue Jul 24, 2018 2:50 pm
Forum: Beginner Basics
Topic: add another TPLink router to mikrotik and allow accounting on different IP subclass
Replies: 3
Views: 864

Re: add another TPLink router to mikrotik and allow accounting on different IP subclass

I believe you need to add a static route for 192.168.8.0/24 pointing to 192.168.1.2 on mikrotik router.
by florid
Tue Jul 24, 2018 2:40 pm
Forum: Beginner Basics
Topic: VLAN segregation and bridge setting [SOLVED]
Replies: 15
Views: 1151

Re: VLAN segregation and bridge setting [SOLVED]

Thanks, @CZFan I followed the wiki and thought about the configuration below. Haven't tested in production yet. Would you please help take a look? Appreciate your time. I want to achieve eth5-ap trunk port leads to Cisco AP which has vlan10 (native) and vlan80. eth1 and eth2 in vlan10, eth3 and eth4...
by florid
Tue Jul 24, 2018 8:28 am
Forum: Beginner Basics
Topic: VLAN segregation and bridge setting [SOLVED]
Replies: 15
Views: 1151

VLAN segregation and bridge setting [SOLVED]

I am using a hex poe router for my home. sfp interface connect to WAN eth1-2 is local lan network eth3-4 connect to IP cams using POE eth5 is a trunk interface connects to a Cisco AP. Create a vlan interface (vlan80) under eth5. Cisco AP has two VLAN, one is a default vlan, the other is vlan80. I cr...
by florid
Tue Jun 19, 2018 4:29 am
Forum: General
Topic: bug persists after updating to 6.42.3
Replies: 14
Views: 5955

Re: bug persists after updating to 6.42.3

By the way , i tracked the hackers MAC-ADDRESS and i found this result : E4:8D:8C:3A:E5:96 .. which it belongs to RouterBoard.Com !
That's your WAN interface MAC address.
by florid
Mon Jun 18, 2018 7:16 am
Forum: General
Topic: One Port with untagged and tagged VLANs?
Replies: 2
Views: 302

Re: One Port with untagged and tagged VLANs?

That's quite easy.
Create VLAN interfaces under ETH2 with the vlan id you want to tag. Eg. from vlan 102 to vlan 106. Create 5 vlan interfaces.
vlan 101 untagged vlan no need to create, just use eth2 should be fine.
by florid
Thu Jan 25, 2018 2:00 pm
Forum: Wireless Networking
Topic: CAPsMAN and group-key-update
Replies: 6
Views: 1968

Re: CAPsMAN and group-key-update

Screen Shot 2018-01-25 at 10.50.08 PM.png Screen Shot 2018-01-25 at 10.51.02 PM.png I noticed some related message in log. And the wireless and clients got disconnected during that time. Not understand why. Both Router (rb960pgs) and AP (wAP ac) are running on 6.40.5. I expect the AP to run as stab...
by florid
Wed Dec 20, 2017 6:32 am
Forum: Beginner Basics
Topic: Port-forwarding 2 Public IP addresses
Replies: 9
Views: 752

Re: Port-forwarding 2 Public IP addresses

The IP shows on the modem starts with 100.64 right? This is not a public IP, it is a private ip scope. Your ISP does another NAT. Nothing you can do other than talk to your ISP to get a public IP address. If you want to do port forwarding, you need to change the ISP modem to bridge mode and let Mikr...