Community discussions

MikroTik App

Search found 18 matches

by kokopelli
Mon Mar 05, 2007 7:29 pm
Forum: General
Topic: Queue Tree & Mangle
Replies: 3
Views: 1052

Are you suggesting creating a simple queue for each network and then use the WAN as the out interface? But I would also love to have a simple queue for each IP later. Doing this would make me have a complex Simple Queue table. The solution lies in creating a mangle for each network and then creating...
by kokopelli
Sun Mar 04, 2007 3:39 am
Forum: General
Topic: Queue Tree & Mangle
Replies: 3
Views: 1052

Queue Tree & Mangle

How can I allocate bandwidth to specific ethernet interface. I actually have four of them. Ether 1 - VoIP - Bridged with WAN - public ip (10.0.0.2/29) unlimited bandwidth Ether 2 - HotSpot - private ip (192.168.20.0/24) - 1024/2048 Ether 3 - LAN - masqueraded - private ip (192.168.30.0/24) - 1024/20...
by kokopelli
Tue Dec 27, 2005 12:57 pm
Forum: RouterBOARD hardware
Topic: Missing Interface
Replies: 1
Views: 1285

Problem Solved! "the pigtails u.fl connector can touch a resistor near the connector and short the mpci card. Then the interface will dissapper. Please check if the pigtail is not touching the resistor (look the bad.jpg image). The pigtail should be just like in the good.jpg image." Sorry Could not ...
by kokopelli
Sun Dec 25, 2005 5:51 pm
Forum: General
Topic: Merry Christmas and Happy new year
Replies: 5
Views: 1388

Same To You!
by kokopelli
Sun Dec 25, 2005 5:43 pm
Forum: RouterBOARD hardware
Topic: Reset to Defaults?
Replies: 3
Views: 1667

Hvae you tried Neighbor Viewer - http://www.mikrotik.com/download/neighbour.zip You can telnet with it using MAC address. Also if you have the new version of Winbox.
by kokopelli
Sun Dec 25, 2005 4:03 pm
Forum: RouterBOARD hardware
Topic: Missing Interface
Replies: 1
Views: 1285

Missing Interface

Merry Xmas!

I just too delivery of some RB 512 Low Power and so far I have noticed that two of them does not show WLAN under Interface. What could the problem be?

Anybody has any experience on this, I dont want to open without getting approval from MT.

Thanks
by kokopelli
Sat Dec 24, 2005 12:49 pm
Forum: Wireless Networking
Topic: 25km 2.4Ghz Point to MulltiPoint
Replies: 14
Views: 3721

Thanks guys, I would give it a shot and get back to you. If I can get 15km radius it would even be ok.
by kokopelli
Fri Dec 23, 2005 8:39 am
Forum: Wireless Networking
Topic: limit bandwidth per IP address
Replies: 14
Views: 40140

I work with a school and we have a high number of use on our network i we get 256/512 from our ISP ,when i use simple queues and gave each Pc 4/10kbps but the system couldnot browse well please what is the minimal bandwith that can cary a system thank [/i] First of all you dont need all that uplink...
by kokopelli
Thu Dec 22, 2005 8:24 pm
Forum: Wireless Networking
Topic: 25km 2.4Ghz Point to MulltiPoint
Replies: 14
Views: 3721

25km 2.4Ghz Point to MulltiPoint

Compliment of the season...

I was going thru MikroTik site and I was wondering if its possible to design a 25km radius of 2.4GHz Wifi network.

Anybody have an ideal of the hardware requirement? CPE should be any wifi radio with 24dbi directional antenna in an urban setting.

Thanks
by kokopelli
Sat Dec 03, 2005 5:11 pm
Forum: General
Topic: Allocate Bandwidth By Subnet
Replies: 4
Views: 1452

Where do I put this? Simple Queue? Also I notice that the refresh rate in 2.9.X is slower that is when I looking at bandwidth usage of an IP address it doesnt chnage as frequent as it does in 2.8.X it doesnt look real time.
by kokopelli
Wed Nov 30, 2005 1:36 pm
Forum: General
Topic: Allocate Bandwidth By Subnet
Replies: 4
Views: 1452

Please that didnt help, I am usign the MT as a bandwidth shapper. I ahve two NIC bridged and the IP is on the bridge. Now I have a VoIP gateway thats outside the MT bandwidth shapper, so what i want is to limit the total bandwidth that goes into the out of the the MT. 1.2mbps IN and 384 OUT. Please ...
by kokopelli
Fri Nov 18, 2005 7:57 pm
Forum: General
Topic: Allocate Bandwidth By Subnet
Replies: 4
Views: 1452

Allocate Bandwidth By Subnet

Hi,

Please I need help on how to allocate bandwidth to subnets and also protocol. The idea is that I want to dedicate 10% of my total bandwidth to Voice. Is it possible!

Thanks
by kokopelli
Fri May 13, 2005 1:34 pm
Forum: RouterBOARD hardware
Topic: Whats Does This Mean!
Replies: 7
Views: 2930

Wow! That would be a difficult one 'cause they were purchased long ago but still have the serial number which you can use to confirm the purchaser.

Also, whats the support email address?

Thank you
by kokopelli
Thu May 12, 2005 6:04 pm
Forum: RouterBOARD hardware
Topic: Whats Does This Mean!
Replies: 7
Views: 2930

I did reboot.

I upgraded the software to 2.8.27 because I had forgotten the password. Now its tellme my demo has expired and has halted!

What can I do to get back my license?

Thank you
by kokopelli
Thu May 12, 2005 3:31 pm
Forum: RouterBOARD hardware
Topic: Whats Does This Mean!
Replies: 7
Views: 2930

Whats Does This Mean!

ROUTER HAS NEW SOFTWARE KEY
----------------------------
Your router has a valid key, but it will become active
only after reboot. Router will automatically reboot in a day.
by kokopelli
Wed Apr 27, 2005 2:18 pm
Forum: General
Topic: Billing Software
Replies: 5
Views: 1892

It can be either Windows or Linux but Windows is prefered. Its just to authenticate MAC addresses and if possible do invoicing etc.

Thanks
by kokopelli
Mon Apr 25, 2005 7:09 pm
Forum: General
Topic: Billing Software
Replies: 5
Views: 1892

Billing Software

Howdy,

Can anybody introduce me to any good free/cheap wireless billing software?

Thank you!
by kokopelli
Tue Jan 25, 2005 10:36 pm
Forum: General
Topic: Link Bandwidth
Replies: 2
Views: 891

Link Bandwidth

Hi,

Can Atheros radio on 5GHz provide enough bandwidth over a 25Km to transport 4 T1 trunks?

Thanks