Do not forget to add custom routes to the Azure Virtual Network. In this case the CHR is working as a soft appliance.

Try to downgrade to 6.47.8 and i think that your problem will be solved.

Hello,
Why hAPac2 and RB3011 have identical ipsec test results?
https://mikrotik.com/product/hap_ac2#fndtn-testresults
https://mikrotik.com/product/RB3011UiAS ... estresults
hapac2_rb3011_ipsec_test_results.png

There is a mistake on the product page. The RB3011 hasn't got IPQ4018 !

- RB3011 port flapping
- CRS328 24p 4s+ crashed if the device has bonded interfaces

- RB4011 ok
- CAP AC ok
- HAP AC3 ok
- CHR ok
- HAP AC2 ok

Hi, I have a few questions with HAP AC3 antenna specifically, and hope the wireless experts on this forum can assist: Are the two antennas identical and are used for both 2.4Ghz and 5Ghz? Similarly, are both antenna connector at the back of AC3 used for both frequencies? Or is one 2.4Ghz and the ot...

The frequencies are loked because of the shared antennas. The two 5GHz RF output cause trouble if the emmitted power is on the same freqency at the same time.

The two 5GHz range is not overlapped so you can select the right interface for the requested frequency without any trouble or disturbancies.

From product specification: "RouterOS 7.0 (compatible only with v7 and above)"

the antenna 2.4Ghz Could it's work with 5Ghz And vice versa ?? and why ??

Theoretically, Yes. If the wave lenght is half or double compare with the original designed wave lenght the transmitted power will be radiated with small amount of SWR. But it is a complex story!

The 3rd band of Audience is useless as it is on a limited channel for meshing I believe.

You can use the 3rd band within the specified frequency range for normal operations not only for Mesh!

Ceee means 5GHz (as 2.4GHz allows Ce at max). Here is (part of) my config: /caps-man channel add band=2ghz-g/n control-channel-width=20mhz extension-channel=disabled frequency=2462 name=f-2462 tx-power=9 add band=5ghz-a/n/ac control-channel-width=20mhz extension-channel=Ceee frequency=5500 name=f-5...

We are using CHR in Microsoft Azure and it would be nice if the Mikrotik image can be used thru Azure Marketplace.

The second missing feature is the Azure Guest OS diagnostic agent that can provide integration with Azure services like Site recovery and VM backup.

The RB3011 USB port has been stopped working after fw upgrade. The solution was downgrade the firmware to longterm and upgrade only the packages but no firmware.

I have updated RB4011 and CRS328-24P-4S+RM and the SFP+ (DAC (S+AO0005)) Rx FCS and Rx Align errors on RB4011 side is solved. Thank you!

The red is not blinking just on with the blue one. The device is dead and i got a replacement from the dealer.

Hi Guys! I have an Audience and after a reboot the red and blue led is on and the device is dead. The LED of LAN ports don't light. I have tried to use another power supply, and POE Switch without any result. I can not put the device in netinstall mode. Is it a well known symptom and/or a dead device?

I have installed a Mikrotik CHR router on Azure and connected to this CHR -> L2TP and EoIP over that L2TP. It worked.

I agree with you! But my tubes in the wall are full and it was a quick and dirty solution If i will have to interconnect my equipments in the rack than the optic modules will be the solution.

My CRS328 has the following POE loads:

- 2 pcs CAP AC
- 1pc HAP AC^2
- 4pcs Hikvision sec. cameras
- 1pc Raspberry PI 3B
- 1pc RB4011
- 1pc RB3011

The System Healt:

It is less than 10 meters CAT5E without shild.

I can not use fiber because of my existing cables. The only one problem with RB4011 is the high working temperature of the SFP+ module.

Yes, i am using S+RJ10 modules between RB4011 and CRS328.