MikroTik

8cqv

Yes I assumed that is what is happening, its really frustrating because all I want to do is tag that port and leave the rest open on vlan1. I do not tag all traffic at the moment just some of the vlan's for cctv, IOT etc. It would be helpful if the manual actually had a definition of what "secu...

8cqv

Thanks P1chl, I had the same issue with that as I did with the tutorial in the manual, once I enable secure on ether1 (uplink) I lose connection to the hap ac2.

Can't solve from my desk now will need to take a laptop to where the router is located as can't connect even with winbox/Mac address.

8cqv

Hoping someone can help, as this is driving me crazy now. I have the following setup: ether1 - Uplink ether2 - Host ether3 - Host ether4 ether5 - CCTV camera I just added the CCTV into the Hap AC2, previously it was on a port from a CRS328 running switch OS that I now need for something else. Proble...

8cqv

DOH, the subscription did not seem to take when I posted this and I just saw the replies, thanks. I'll edit the file and try again, over serial so I can at least see where it gets to (over ssh/winbox I was losing connection and the point of failure). Very frustrating it exports something that can't ...

8cqv

Been going round in circles, maybe I am missing something stupid hoping someone can help. I have an RB3011 that is running 6.44 where the config has been reset and I am trying to import and previous config export (config also exported at 6.44). When I run import through winbox or with the reset-conf...

8cqv

Interesting that RoS spins the fans at 2000rpm, SwOS runs around 4500rpm until it locks up the fan controller and you get 6000rpm jet engine: F3B15E69-DD1E-4FEE-A123-3AA7EEC12818.jpeg Must change mine over, but it means reconfigure from scratch with vlans for cameras and I keep putting it off in the...

8cqv

Sounds good! One more question: does this also mean that if I have only a limited POE power request (8 devices with max 7 Watt/port) then my device won't turn on the fans? How it goes in your case? My experience (with SwOS) is that you will have fans running yes, maybe stop/start (repeat at 1m inte...

8cqv

I had the same issue and changed from SwOS to RouterOS which resolved the fan issue I was having. I had a thread here somewhere about it. At the moment it's running perfectly on 6.44. as it's a core switch I haven't had a chance to update it in a while. Yes they don't seem to care about SwOS at all...

8cqv

Still broken, no word from support on when a fix is coming.

Fans just go into full speed, fault light comes on, but monitoring shows no error and default rpm.

8cqv

Fan control still completely broken for CRS328.

SwOS is a bit of a joke isn’t it really? How can fundamental problems not be addressed, especially with so much delay between releases?

8cqv

I have put 2.9 on CRS328, but I cannot get it to load on my CSS326 (using FW file in both cases). As it totally screwed my network last time I have not enabled the 10g uplink yet until both are on 2.9 but I see nothing in the release notes about the problem being fixed? Fan's also did some weird stu...

8cqv

Better they stay on, than stay off (when it all get red hot, temps are reported wrong for the board as well)

Given the risk of hardware damage, I am amazed MikroTik have taken so long to fix SwOS...

8cqv

Its firmware bug in SwOS, have a look here for more discussion: https://forum.mikrotik.com/viewtopic.php?t=132553#p685035 What I found was it was a very small PoE load that seemed to confuse it, now I a couple more devices 4-5w each the fans just run 24*7. Its a worrying problem as once the fan cont...

8cqv

No, support have no fix. I was having huge random problems as it was my trunk between the switches, in the end I had to disable to port and use a 1G port for the trunk. Not great is it :cry: Support said to use ROS, but I don't want ROS on the 328 because its just a switch and SwOS is much quicker t...

8cqv

Ordered one today since it's now available at several resellers.

Waiting for everyone in this thread to buy one and test it before ordering mine!

8cqv

Nice
$150RRP I like it, POE in as well on the 1G port.

8cqv

Have the same thing.

Does your software report as 2.7p or 2.8?

My CSS326 just arrived today to go alongside my CRS328 but the flaky SwOS behaviour is worrying...

8cqv

My crs328 has been reporting this for some time, there appears to be error in the update server info

8cqv

Today's latest weirdness:

Not sure I believe these fans of 14K, plus the board is not in a fridge...

8cqv

Also waiting for one of these, the mum HW thread had a quote from support "before March 2019":
viewtopic.php?f=3&t=132822#p670275

8cqv

https://wiki.mikrotik.com/wiki/MikroTik ... lity_table

8cqv

Thanks for updating, I actually have my CSS326 on the way to run alongside 328 and replace an old netgear (Java GUI no longer supported) - will try the same test I am goign to try a DAC though not optical.

8cqv

Is SXT SA5 ac 48v or 24v? I am not in front of my hAP AC^2 but I seem to recall the PSU is 24v... EDIT: Powering Details PoE in 802.3af/at PoE in input Voltage 12-57 V Number of DC inputs 1 (PoE-IN) Max power consumption 12 Max power consumption without attachments 12W https://mikrotik.com/product/R...

8cqv

I am also curious why the instructions say to set DNS and gateway to the PC - they are not used in a direct link like this. I had a fight my AC2 the other day after a power problem during config change and so was using the Wiki, had a big struggle till discovered I still had another interface up on ...

8cqv

Imho the lack of switch chip features could be neglected if you had the possibility to connect a "real" switch to the 10G port via a cheap cable. However, the lack of passive DAC support forces you to spend 100+€ for this connection instead of ~25€. Combining both these weaknesses into an...

8cqv

I think it will be a good seller, especially in parts of the world with 1gbit Fibre at home is available, I think most people in the thread so far have a specific use in mind and so for them the feature set may not match their use case, but that's the same with most of the mikrotik range right? You ...

8cqv

Footnote 4 says you can only use a SFP+ DAC at 10Gb Doesn't it rather say that you cannot use passive SFP+ DAC at all? RB4011 seems to be the only Mikrotik SFP+ device which is incompatible with Mikrotik's own direct attach cables. It does in the latest edit, it didn’t this morning when I posted...

8cqv

I could swear that 4011 was not listed there yesterday, when I posted this question here... :shock: This page was last edited on 21 September 2018, at 09:38. Just looked, looks like info was added this morning :lol: I had the page bookmarked so checked it and posted the link earlier. In fact the fo...

8cqv

Why not use the compatibility table?
http://wiki.mikrotik.com/wiki/MikroTik_ ... lity_table

S-RJ01 not supported. S+RJ10 is supported, no mention of any restrictions under the S+RJ10 section.

Footnote 4 says you can only use a SFP+ DAC at 10Gb

8cqv

Port status LED is below the group of ports:

Is that what you mean?

8cqv

Just realised it works with CRS328 in ROS talking to CSS326 in SwOS that will be good enough for me.

Like the rrdtool graphs, what are you using mrtg?

8cqv

Did support solve this for you?

I want to add a CSS326 to my CRS328, but worried about the issues you had with the trunk, CRS326 is a lot more expensive just to get ROS (and SwOS works well for a switch).

Do you have a DAC cable to try? Could it be FC specific?

8cqv

Yes but notice how the build date is different for the two 2.8 versions in your screenshot, installed and available.

8cqv

I rebooted it earlier and noticed in winbox it reports as v2.8?! Will Check when I have tome in the GUI. I plan to use the 10gbit port with fibre, but I am waiting for longer cables to arrive to put through the house so can’t comment yet, I saw the thread on it. EDIT Ok the Upgrade tab in SwOS shows...

8cqv

I used the new swos option under ROS on my crs328 to set IP earlier in the week, it works but you have to be sure crs328 cannot see a dhcp server or it takes that IP from dhcp instead of the configured one.

https://wiki.mikrotik.com/wiki/SwOS/CSS ... g_RouterOS

8cqv

Looking at the Ethernet test results of RB4011 vs RB1100AHx4 - How is the RB4011 pulling better numbers? Where's the difference? The test results seem to be a sum of all ports, so with 4011 having 10gbit sfp+ with its own 10gbit lane to cpu (according to the block diagram) the aggregate throughout ...

8cqv

That’s what it offered as an upgrade, it only had 3 fixes over 2.8 but one of those was 1gbit sfp in crs328 so I applied if.

8cqv

I have now "switched" (see what I did there) over to SwOS 2.9 and the fans just seem to run 24x7, but at least its consistent.

8cqv

At least you can see the antennas are fixed, as they seem to be using u.fl to SMA to N to do the test.

Still plan to buy the rackmount one to replace hap ac2 routing, shame about the switch chips but doing my switching in crs328.

8cqv

For reasons unknown my fans just seem to run 24*7 now even when cpu cool, very strange. > system health print cpu-temperature: 34C power-consumption: 4.2W board-temperature1: 27C psu1-voltage: 26.4V psu2-voltage: 52.6V psu1-current: 0A psu2-current: 0A fan1-speed: 4020RPM fan2-speed: 3990RPM Quieter...

8cqv

I thing 4x U.FL http://certid.org/document/3948605 I saw they are U.FL internally, but what worries me is that if you look at the outside pics: http://certid.org/document/3948604 It looks like the RG316 (or whatever the cable is) passes through the hinge and the antenna is fixed, I understand why t...

8cqv

I’ll take the horsepower over the features though for my needs. Can anyone from MikroTik confirm the antenna are removable on SMA or something? My router lives in a rack so I need to use tails to take antenna outside if using a combined router, given spec of the WiFi model would go for that as long ...

8cqv

I would imagine its not the CPU but the cooling of all the POE parts that require the fans? as you note the CRS326 is fanless. I am sure there can be a fix, I have not tried SwOS yet, I might try that as I am only switching but I think SwOS only got fan support working in 2.8 just released. I am sur...

8cqv

If you google the wireless model you get the fcc report, it has internal pictures: No Fans

Case looks Matt like the AC^2, and plastic?

The main problem for me... is I want a new router now and it’s not on sale yet!

8cqv

Or set fan RPM so they run half speed all the time. Mines in a wall cabinet, but no front door and plenty of air flow so my feeling is threshold of 40c is a bit low for real world, could do with tuning a few C higher...

8cqv

So yeah, I bought one and even in ROS the fans stop, start, stop, start etc, running latest release FW with just one POE device pulling 5w worst case (IR at night). Hoping next FW has higher threshold for fans or options to tune. I would class the fan noise as annoying, but not data centre switch lo...

8cqv

Thanks for the feedback. Support also replied that the fans are temperature sensitive, but interesting to know that swOS has problems with the fan control. Not ordered one yet but it does perfectly fit what I need (apart from not physically fitting in my wall mount rack...) You can probably do every...

8cqv

LDF2 looks really cool as well, I have absolutely no practical need but now I want to experiment!

8cqv

In the absence of anything official from MikroTik so far I've gently harvested a few screenshots from the live stream here https://www.steveocee.co.uk/mikrotik-mum-europe-2018-new-product-announcements/ thanks for posting, no prices on the switches I noticed so likely some way out? Any verbal price...

8cqv

Mine is the same, noticed when on my desk during setup, now it’s on the wall downstairs I can’t hear it. Only happened under WiFi load and I suspected something in the RF circuit was the cause.

Works ok, I had forgotten about it till I saw your post. I am using supplied wall adapter not PoE FYI.

8cqv

Thinking about getting a CRS328-24P-4S+RM rather than the CRS326 I had planned, but I am concerned the fans might be noisy if there are two and they run 24x7. Can anyone advise if they are temperature sensitive like the CRS317? I will not be using much of the PoE capacity, but going with 328 over CR...

8cqv

Its strange right! Both subnets can access the internet, but for example a wireless client cannot send email (email server on 10.x network) or load a webpage from a pi serving on the 10.x network. I looked at interface lists last night, but there were none configured. Basic setup: - New unit - FW up...

8cqv

ROS is latest production, 6.41.3. I cannot access the router at the moment but I will check "interface export", that's a new command! At the moment I am running with a bridge for eth5 and DNS server and IP assigned to the bridge. I have tried it native as well on eth5 but its possible some...

8cqv

You will get routing between the interfaces according to the rules you make. thanks, so firewall rules? I just tried adding: ip firewall filter add chain=forward action=accept src-address-list=192.168.88.1/24 dst-address-list=10.10.1.1/24 ip firewall filter add chain=forward action=accept src-addre...

8cqv

I am hoping someone can put me out of my misery as I have been going round in circles with this now since last week and I am sure I am just missing something fundamental. I have a hAP AC^2 (RBD52G-5HacD2HnD-TC), connected as follows: ether1 - PPPoE connection to DSL modem ether2, ether3 & ether4...

8cqv

From my research the CRS112-8P-4S is not a viable router for a main connection, in my original post here I was looking to use the CRS326 as my router as well as a switch, CRS326 has a much higher performance over the CRS112 for routing. I was planning to add 112 just as a switch for the PoE alongsid...

8cqv

Thanks for feedback, that's what I thought. I realised that the 750gr3 has better VPN support, but my VPN requirements are very limited to the odd troubleshooting connection - no big throughput requirement. Interesting comment on the 326/328 chipset though, I thought they were the same? CRS326 - 98D...

8cqv

Hi, new to Mikrotik, I am going to try and ask my question as clearly as possible having read the forum guidelines, lets hope I succeed :) Background This is my home setup, currently I have: BT vDSL Modem <=> Draytek Router/Wifi <=> Netgear 24 port GbE <=> 3Com 10/100 PoE switch (16w total provision...

Search found 58 matches