You are on your way, but pause and consider the task you wish to accomplish. Your layer 3/routing is not displayed in your configs, but we will assume this is up ok. You wish to bridge two LANs for performance, not overlapping subnets. Consider MPLS apart from VPLS, VPLS simply transports over the l...

Have you worked this out yet, let me know, I'll post some configs if you still need em.

Your looking for an ip sla and/or track type function. One suggestion, A. There are existing configurations presented by others that detail load balancing using ospf cost to manipulate traffic direction, also provides failover in event one link goes down, ospf does its normal job and routes all traf...

Not sure what you are trying to accomplish, but any redundancy, failover ect. would be done apart from vpls. If you have (VPLS ptp or mesh design) and provide layer 3 redundancy below, vpls will reform, vpls runs on top of other protos. I hope this is OK, but if you could post description of the top...

Hello, I design, spec and oversee the construction of large scale wireless WAN's. Currently I operate a very large system which employs mpls/vpls covering 300 square miles (and growing). I see Cri provided a link to Link Tech's there are others, but out of curiosity what is the motivating factor for...

It gets even better with the broken paypal issue and no ability to make a clean upgrade from an older version to the new 5.22 which is claimed to fix the paypal http bad response. Curious.

The changes that paypal made to their system is the reason for the failures. My system has been experiencing the same problems for the same amount of time. Here are two links from paypal that describe their change. https://ppmts.custhelp.com/app/answers/detail/a_id/92 and https://www.x.com/node/2178...

Example: 0 Mac address 12:34:56:xx:xx:xx signal stength range -91..120 yes yes 1 Mac address 78:9A:BC:xx:xx:xx signal strength range -85..120 yes yes 2 signal strength range -88..120 yes yes 3 signal strength range -120..120 no no Reason: We have a large deployment of two specific vendors and then e...

I think it is a possible solution, not sure about good. Is roaming absolutely required? I ask because of the additional complexity and troubleshooting you will encounter once you commit to the mpls configuration. I actually operate a very large contiguous mtk mpls network and this is mostly stable, ...

First, check the watchdog timer and disable it.

The guest vlan can access the Internet OK, but cannot open guest login nor access internal sites, Are you using Mikrotik hotspot to deliver login? also if you may ping both directions accross net have you tried opening sites/login by IP address to see if it is an internal resolution issue? Post a de...

I'm setting up a network where multiple paths will exist accross network and multiple egress points will exist from network to world. Network is designed such that client network will allow a host to roam extent of network on initial issued IP address. So there is a possibility that client gateway c...

can you place a tick box beside caller id so that if the tick box is ticked user macid will be automatically placed to his caller id when he will login for 1st time & also make that box default ticked when we add new user. It is already in our feature request list and will be implemented. Is th...

Overview - Working Hotspot system clients authenticate w/usermanager queue assigned to client dynamically OK. Scenario - One client needs to bypass hotspot. Issue - Need to assign simple queue to bypassed client for BW control Problem - Can not seem to affect client with queue. Question - How can I ...

This can be forwarded to include 3.17 as an issue in fact there were problems with vista and 2.9.51 as well. The symptoms are commonly as follows. Vista has trouble opening logon page, sometimes can not open at all. Vista PC has A LOT of trouble if IPV6 is enabled I have had to disable this on each ...

Thank you sergejs and the Mikrotik team.

The question then becomes, what, if anything will be done to fix this issue. I am more inclined at this point to consider a configuration change by paypal as the most logical cause for this issue.

Mine has broken as well same symptoms, started about three days ago has worked great for almost two years. My location is south florida USA if that may be of use. I have verified my usermanager config is OK. No reply from ping to http://www.paypal.com, but name resolves good. Latency does not seem t...

My current MT systems connect to Internet through Frame Relay. cloud<--->Cisco<--->MT/UM<--->MT/HS I want to put up a new site but to use DSL for connection to Internet. cloud<--->DSL<--->MT/HS or maybe cloud<--->DSL<--->MT/UM<--->MT/HS What should I look out for with using the DSL front end? I gues...

This link should help. You set the ip and secret for your usermanager on the client system.
http://www.mikrotik.com/testdocs/ros/2. ... radius.php

Would'nt the in-interface be the public. I'm using 2.9.51 and have found that an in-interface did not need to be defined. I tested this assiging in-interface=local_net and would not map. this was working nat rule from my 2.9.51 chain=dstnat action=dst-nat to-addresses=172.x.x.x to-ports=80 dst-addre...

web browse to usermanager and select logs or sessions and in the upper right there is a drop down allowing you to change the number of items displayed. Select 1000 and then select all and remove. with 13K you still only have to repeat this 13 times. I think from new terminal it would be tool user-ma...

My hotspot system works well in combination with userman and paypal payments. The problem I am seeing is 1 - user purchases time using paypal OK 2 - user logs in and uses time OK 3 - user time expires too bad OK 4 - user proceeds to https:\\host.domain.com\user to add credits OK 5 - user selects cre...

Thanks, this worked

I have followed the steps repeatedly to create a certificate request and it does not work. I create the request but when I try to import nothing happens. The certificate-request.pem and the private-key.pem file can be seen in the file system, but will not be imported or decrypted, no matter what met...

I have followed the steps repeatedly to create a certificate request and it does not work. I create the request but when I try to import nothing happens. The certificate-request.pem and the private-key.pem file can be seen in the file system, but will not be imported or decrypted, no matter what met...

This worked, thank you for the advice.

Hello, I have Mikrotik running HotSpot authenticating on Mikrotik connected to Internet. wireless user >192.168.x.x-TIK_HOTSPOT-172.16.x.x~~~~~172.16.x.x-TIK_USERMAN-209.x.x.x Without hotspot enabled I can connect and browse to any destination. When Hotspot is enabled I can only browse, by IP addres...

I have the same problem, tried many different email address and different formats, still no luck.
xxx@xxx.xxx.xxx
xxx@0.0.0.0
xxx@xxx.xxx