MikroTik

raymonvdm

I`m currently using a Cisco 2960s switch where i disable two ports using SNMP from time to time (using HomeAssistant) the ports are used by the kids to play with IP Telephones.

Does SWos support SNMP set or write? The switch i`m using is a CRS328-24P-4S+RM

raymonvdm

It seems that Router 7.1 fixed my non-working ethernet interfaces for all but Ether12 on an RB1100 X2 AH
viewtopic.php?t=178341#p880735

raymonvdm

Just upgraded my RB1100 X2 AH from v7.1Beta6 (where there is no traffic passing on the majority ethernet interface ex eth1 till eth8 and eth11/12/13) but now i`m stuck witch cpu stuck [admin@MikroTik] > system/reset-configuration Dangerous! Reset anyway? [y/N]: y system configuration will be reset R...

raymonvdm

When running 7.1beta6 on a RB1200 the Eth1 - Eth8 are not working. The link state is correct but there is no traffic passing the ports (same when using 7.1beta4) the Eth9 and Eth10 seem to be working fine https://i.mt.lv/cdn/product_files/RB1200_180301.png [admin@MikroTik] /interface/ethernet> print...

raymonvdm

I`m running my network for quite some time and it was working fine until a couple of days or so. I`m not quite sure but it seems to be related to a RouterOS upgrade on a CRS125-24G-1S 2021-04-06 00:39:32 system sw05.kmp1 OS Version: 6.47.8 -> 6.48.1 I have found the following change in the versions ...

raymonvdm

Looks like problem with restore with my chatea 12 router, today for few minutes electricity was gone in home and after router start with reseted all settings. I have saved before some backup in local pc, so I try to restore but after restore command router restarted and again all settings reseted t...

raymonvdm

Installed RouterOS 7.1beta4 on a RB1200 but i`m having some issues with ether1 till ether8, they were working fine on the 6.x beta but now they hang on searching for DHCP ip. The interfaces ether9 and ether10 work fine and none of them are in a bridge Which might look like a switch2 is missing issue...

raymonvdm

I just found out this topic after getting two 1100AHx2, the fans are not really noisy but they are more of the wining type. The main fan, has more issue with it than the aux fan (so i switched them in the Healt menu) Maybe the fans are just end of life to :-) The included fans are just 40x20mm fans?...

raymonvdm

Maybe the issue is related to the following, but i`m not sure why. What is the meaning of "drop-if-no-vlan-assignment-on-ports" /interface ethernet switch set drop-if-invalid-or-src-port-not-member-of-vlan-on-ports="ether01-Trunk crs1.kmp1,ether02-Trunk crs2.kmp1,ether03-PP18-CRS-Link...

raymonvdm

I`m running two of these units but sometime i`m having issues with port trunk. The interfaces are all slave of ether1 and the switch is handling vlans. I`m only using the device as switch. SWos should be sufficient for me, but it doesn`t seem to be available for this device type so i`m using RouterO...

raymonvdm

I`m trying to tag untagged traffic comming in on ether2 to be tagged with vlan160. But i cannot get it to work.

I`m running RouterOS 6.43 on a 2011UiAS which has the Atheros 8327 switchchip.

Can anyone explain which steps to take? Since the above steps didn`t gave me a working setup

raymonvdm

The RouterID can never be an IPv6 adress

raymonvdm

I`m trying to setup BGP using a Mikrotik Router and ExaBGP daemon but the peer is not established. /routing bgp instance set default as=12345 client-to-client-reflection=no router-id=192.168.110.252 [admin@crs2] /routing bgp instance> /routing bgp peer add address-families=ipv6 name=nsx-1 remote-add...

raymonvdm

I`m trying to setup IPv6 DHCP Relay but it looks like it doen`t do anything. The wiki is still missing so i don`t know which values to configure

raymonvdm

I stumbled across this topic because i wanted to add an management interface to a Mikrotik which is not included in the main routing table (so the management network is never reachable from the normal network) I tried to achieve this by placing a loopback0(bridge) and ETH13 on a RB1100 in a VRF. I s...

raymonvdm

The distance=200 was set to kick the OSPF process and seems to be left behind, and was indeed causing issues after the router was rebooted. Before that it didn`t change a thing. I use the filters to prevent accidentally redistributing a static route which is not for 192.168.x.x

raymonvdm

I thought i did, but cannot find the email anymore. Therefore is just contact support again to see if they can help me out

raymonvdm

I have setup a network of Mikrotiks running OSPF between multiple sites. Some sites have a single internet connection and one MT. Others have multiple On one of the double router locations i lost one of the MT`s. The lost of the MT should not be an issue but i found out that my setup is not working ...

raymonvdm

The unit is upgrade to 6.40.6 but without any solution. Powerflip is always the solution. RouterOS is up2date, firmware is up2date. I have two of these units on the same location, and i just found out that both of them are experiencing the same issue [admin@crs1] /interface ethernet> print Flags: X ...

raymonvdm

I`m currently running multiple Routerboards but one of them has issues while rebooting using software command (CLI of WebFig) The router seems to reboot but the interfaces are no longer there, these are the last log rules 14:09:54 system,info,account user admin logged in from 192.168.112.52 via ftp ...

raymonvdm

The reboot of the switch seem to do the trick. But it is very time consuming to find out the issue in the first place

raymonvdm

I`m having connectivitie issue in my network (some hosts kan ping an IP others can`t) and i just found out that the issue is due to the Unicast FDB being incorrect I have had a static entry in the past, but it look like this is still giving issues [admin@sw05] /interface ethernet switch unicast-fdb>...

raymonvdm

I replaced the gateway of our current wifi network with a Mikrotik Router and enabled Hotspot features for the Wifi VLAN. This seems to be working fine, but with two issues so far IPhone needs to reconnect everytime The iphone users need to relogin everytime the phone reconnects to wifi. Which is st...

raymonvdm

I'm sorry I forgot to mention that. You also have to add the IP addresses you're NATing to the WAN interface on the router in order for the NAT rules to work... I'm not sure if you can add a whole subnet to an interface unless its done one at a time. I could be wrong though, try it out? I also need...

raymonvdm

I currently own a bunch of Mikrotik Products to support my Home/Office network and the network itself seems to be working fine. - RB450G NAT Gateway - CRS Switch (CAPS Controller) - RouterBOARD 941-2nD (CAP/Switch) When i perform a speedtest on my WileyFox Android device (connected to the 941-2nD) i...

raymonvdm

I have the same issue, the IPv6 pool shows a /64 handed out to the connection. But the client has no ipv6 address on the local interface. When i perform a tcpdump on the tun0 interface i don`t see any IPv6 attempts or wat so ever tcpdump -ni tun0 ip6 tcpdump: verbose output suppressed, use -v or -vv...

raymonvdm

I just upgrade my RB450`s to RouterOS 6.38.1 and this broke my setup. I`m not exactly sure why but maybe some can explain it to me in more detail Router1 has a LAN_Bridge running VRRP110 (VLAN110 as only port in the bridge) Router2 has a VLAN110 interface running VRRP110 Note: Both routers are conne...

raymonvdm

Is there a difference when testing using routeros version 6.37.1 ? Since i`m having some issues with the following change in 6.38 Important note!!! RouterOS v6.38 contains STP/RSTP changes which makes bridges compatible with IEEE 802.1Q-2014 by sending and processing BPDU packets without VLAN tag. T...

raymonvdm

If it would support IGMP Snooping it wil make it a beter product. But when i look at the changelog of swOS there is no reference to IGMP Snooping. So i gues the answer is no.

raymonvdm

I`m running a Transparant Mikrotik Proxy for quite some time now. But i would like to know how to set this up for IPv6. The IPv4 part is using a DNAT rule to redirect al port 80 traffic to port 8080 (proxy port) however IPv6 does not support the NAT option

raymonvdm

I currently have a hospitality WiFi network which is based on a Cisco router, and a Cisco WLAN controller using several access-points. The WLAN controller and access-points are working fine and don`t need to be replaced. But i would like to replace the Cisco router (Cisco1841) which is currently fun...

raymonvdm

I have an similar issue when using a CRS and a setup box connecting to the switch of an HAPlite. I tried to block multicast traffic on the bridge in the switch of the to limit the traffic to ether1 (uplink) and out ether3 (port with the setupbox) but now i lost management #resetandtryagain The input...

raymonvdm

I don` t use IPv4 for OSPF but i`m using BGP to route my internal 192.168.x.x traffic and it is working fine. Since i have my own /48 subnet i would like to use it on several location in my "Home" network But for now i`m can`t even get two routers who are directly connected by ethernet to ...

raymonvdm

You`re talking about a loopback interface (bridge) but in the example there is no Loopback

raymonvdm

Yes but now i need to figure out how to configure OSPFv3 since the example is not working for me (Yet) so i`m searching for a better real life example

raymonvdm

I think you mean i can just configure "public" ipv6 adresses but i already had the following adresses configured R1 2001:xxx:xxx:83::220/64 R2 2001:xxx:xxx:83::252/64 When i check the ping tool and ping from the ppp interface i still get timeouts I have started torch and the ping packets a...

raymonvdm

I have several Mikrotiks running in my network and i would like to understand and build a IPv6 routed network on top of my current infrastructure I have an IPv6 subnet /48 (ISP) on one location and i would like to use some subnets of this subnet on another location http://wiki.mikrotik.com/wiki/Manu...

raymonvdm

I noticed that the access-points are quite often changing for channel to channel. I have not found a way to restict this except setting a specific channel

However is still see disconnects on especially Android Phones

raymonvdm

I`m testing with a Huawei E3531s-2 on a CRS125-24G-1S-2HnD-IN and the Huawei seems to be working if you plug the stick in and poweroff/poweron the unit. Reboot is not sufficient. The Huawei seems to be acting as a NAT router using 192.168.8.x subnet on the USB side of the dongle and the public provi...

raymonvdm

Currently this sim card is not provided with a public IP adres. But another sim card in a Cisco Router with 3G interface is publicly reachable and equipped a public IP

raymonvdm

I`m testing with a Huawei E3531s-2 on a CRS125-24G-1S-2HnD-IN and the Huawei seems to be working if you plug the stick in and poweroff/poweron the unit. Reboot is not sufficient. The Huawei seems to be acting as a NAT router using 192.168.8.x subnet on the USB side of the dongle and the public provi...

raymonvdm

What is the best setup for wifi on the HAP Lite?

I have two of them running as CAP device but i have issues with the wireless connections and i`m not sure what to enable and what not

Do in need to enable HT RX Chain / HT TX Chain ?

http://forum.mikrotik.com/viewtopic.php?f=7&t=103701

raymonvdm

I have made the following changes in the setup to make it more straight forward RB450G The was are bridge on VLAN110 which was used to connect the "SSID wifi" to the vlan and it is now removed This is the config on the CAPsMAN /caps-man datapath add client-to-client-forwarding=yes local-fo...

raymonvdm

I`m already using these kind of rules which seem to be working fine since the client is rejected on the first floor access point. But it is also rejected on the ground floor access point but not based on the access list but based on the wireless interface handshake itself

raymonvdm

I have the following setup but i`m still having some issues with clients who are connecting to the "wrong" access point RB450G - CAPsMAN CRS125-24G-1S-2HnD - Switch RB941-2nD - Access Point Groud Floor RB941-2nD - Access Point First Florr I have the following rules add action=accept commen...

raymonvdm

I think i have the same issue after an upgrade to CHR 6.34RC21

Although the CLI is more usefull (key replaced by xxx just for privacy)

[admin@router] /system license> print 
  system-id: kThxxxxx/xx
      level: free

raymonvdm

I just upgraded the CHR to v6.34rc20 and now i` m unable to login :shock: I *tried* to update to 6.34rc20 but I get this error message: ERROR: not enough disk space, 26.3MiB is required and only 17.2MiB is free This is on the default VHDX version of 6.24rc19 with The Dude package added and running....

raymonvdm

I just upgraded the CHR to v6.34rc20 and now i` m unable to login

raymonvdm

I just received the email about RouterOS v6.34 RC (The Dude and CHR) and downloaded CHR VMDK :D I uploaded the VMDK to my ESXi host and created a VM out of it. After that i have exported the VM to an OVF file and uploaded it to a Hosted "VMware vCloud Platform" After the import the templat...

raymonvdm

The data should be coming in as tagged vlan 4, this is also the rule that is matching. "If traffic comes in tagged with vlan 4 then tagged the traffic with vlan 4" :? For now it is working for me and i will put the issue in the refrigerator. I will now wait for IGMP Snooping on the CRS pla...

raymonvdm

I think i made the setup correctly :? [admin@sw04] /interface ethernet> print Flags: X - disabled, R - running, S - slave # NAME MTU MAC-ADDRESS ARP MASTER-PORT SWITCH 0 R ether01-Trunk crs1.kmp1 1500 xxxxx:AE enabled none switch1 1 ether02-Trunk crs2.kmp1 1500 xxxxx:AF enabled ether01-Trunk crs1.km...

raymonvdm

I think i found a bug.. Switch --> VLAN --> In. VLAN Tran I have one rule to set all the untagged traffic to bogus vlan 400 Ports: Ether8 Service VLAN Lookup for: any Customer VLAN Lookup for: any Customer VID: 0 New Customer VID: 400 And the IPTV is not working but a soon as i add the following rul...

raymonvdm

I`m using a CRS125-24G to switch my network.But i seem to have some issues with assigment of vlans :shock: - ether1 is the master interface - ether2-24 are slave interfaces of the master interface I have a Cisco router which gives me a IPTV vlan (vlan4) so i created a vlan 4 on the switch and connec...

raymonvdm

I have replaced the RB450G with a new board and power supply and the issue still remains. I have upgraded the units to 6.30.2 (RB450G and the hAP lites) but the issue occurred again last night. There are no schedules for the timeframe in which the crash occurs and Nagios told me the issue started on...

raymonvdm

For several years i`m using a RB450G without any issues but since i connected two hAP Lite units and enabled CAPsMAN it seems to reboot from time to time . Or when my wifi stops working i need to reboot the RB450G to get the wifi working again. Last night (25-07-2015 01:25) i rebooted the RB450G bec...

raymonvdm

Is there also a way to tag all untagged traffic with a vlan tag (110) and to let tagged traffic be passed (4 and 15) arround the ingress translation. The ingress translation is now tagging all traffic and not only untagged I want to achieve a access vlan (untagged) and voice vlan (tagged) like cisco...

raymonvdm

I have set the bootloader to the old version and now the router is booting fine. However this might not be a permanent solution. I hope Mikrotik Support will respond.

raymonvdm

Hi, For quit sometime i` m using serveral Mikrotik routers and today i have rebooted a RB450G running firmware 3.10 and RouterOS 6.28 but it did not succeeded the reboot. The router is not coming back online. After some trial and error i found out that when i push the reset button and apply power to...

raymonvdm

I`m trying to setup my IPv6 subnet using two uplinks to my ISP but i`m looking for the best setup. I have two independent gigabit uplinks from my ISP one connecting to each of their core routers. Both mikrotiks are also connected back to back using a gigabit interface ISP router config router1.isp i...

raymonvdm

I was troubleshooting an issue with one static dns entry which is no longer there, but the cache thinks it still is The cache entry Name piboven.domain.com Type A Data 192.168.110.72 TTL 1d 00:00:00 The static entry Enabled Yes Name piboven.domain.com Address 192.168.140.146 TTL 1d 00:00:00 Clear Ca...

raymonvdm

I also just upgrade from 6.19 to 6.22 and now my 6to4 tunnels are broken (SIXXS) the are running / not running

And the both have a IPv6 static route to keep the ping going bacause i don`t always use them since my provider sometimes gives me Native IPv6 when it is not broken

raymonvdm

I have the following setup and since some time i have VoIP issues. I think these issues occur because my wan upload is full. So i want to use Queues but it is not working so far Location1: (50/5mbit VDSL) Some SIP phones with a Static DHCP ip adres, so the phone always gets the same ip. Routerboard ...

raymonvdm

Today i swapped one of the wireless card with a card i recovered from a HP AP420 access point it is also an AR5212 card but the difference is that this card is indeed working with AES encryption The cards i bought in the past are equipped with an AR5212-ESI chip and the card from the HP AP carry an ...

raymonvdm

This weekend i found my old Mikrotik RB192 when cleaning out my closet. Now i tried to build it up again and use it as my outdoor wifi access-point but yet without success. RB192 2 x miniPCI wireless card AR5212 - One interface configured as "station" connection to my Provider Wifi AP. (Cl...

raymonvdm

I`m currently running ipv6 using a 6to4 tunnel provide by SIXXS but now i`m trying to use the IPv6 subnet my provider has provided me but i can`t get it to work Router1 Cisco 887VA-SEC-K9 running DHCP on Dialer0 and Static on VLAN1 Dialer0 ipv6 address autoconfig default ipv6 unnumbered Vlan1 ipv6 e...

raymonvdm

Tonight i upgraded my second RB450G and it is the third device (RB750G and RB450G where device 1 and 2) which fails after the upgrade (ethernet interfaces lost) I made an Sup.Out and send it to support. Let`s see what happens next

raymonvdm

My problem is also related to 6.5. I have done the following to resolve the issue - Reset to factory default settings - Firmware downgrade to 5.26 - Restore email.backup Unit is running fine When i upgrade the unit using 6.5 the unit is broken again. The issue seams to be related with the ethernet s...

raymonvdm

I got serial console access to my RB450G board and it looks like the ethernet interfaces are lost. [admin@mt4.xxxx.nl] > interface print Flags: D - dynamic, X - disabled, R - running, S - slave # NAME TYPE MTU L2MTU MAX-L2MTU MAC-ADDRESS 0 R bridgeTV bridge 1500 65535 02:79:36:02:32:AC 1 RS eoip-tun...

raymonvdm

Sorry my bad, i just downloaded the 6.4 versions yesterday and just dropped the wrong file link. My actual problem is that the unit which is upgraded using the upgrade packages is fine. But the units upgrade with the all_packages zip no longer work after uploading all used packages and a reboot.

raymonvdm

raymonvdm
please proceed to download page to download 6.5 version,
http://www.mikrotik.com/download
and upgrade your routers to 6.5 version.

I first need a way to recover the units as one of them is 130km away, this can be some kind of an issue

raymonvdm

I just upgraded three units to version 6.4 - Unit one RB750G using the http://download2.mikrotik.com/routeros/6.4/routeros-mipsbe-6.4.npk (works fine) - Unit two RB750G using the http://download2.mikrotik.com/routeros/6.4/all_packages-mipsbe-6.4.zip (uploading the needed packages) (unit is dead) - U...

raymonvdm

I just noticed something strange with my RB450G, the device is fine for more then a year now. It is connected to my Linksys SLM2008 and running okay. Now i have foun myself a new switch (SRW2024P) and when i connect the switch al seems fine for a couple of seconds and then the routerboard reboots (l...

raymonvdm

I`m using 5 ethernet interfaces on the RB450G. So i don`t undestand your issue with the RB450G

The default gateway for your lan network should be the Mikrotik machine. On the mikrotik machine your should create a more specific route too reach your vpn desstination.

raymonvdm

I have a little update on this because i changed the following - PPPOE tunnel is created to connect to my ISP - PPP Profile is made for that tunnel to try to get the interface unnumbered (Just like a Cisco would) - Public ip addresses are bound on VLAN4 subinterface on LAN I can ping to the ip adres...

raymonvdm

Is it possible to send a ping using tools -> ping in Winbox of WebFig with source interface the pptp tunnel ?

raymonvdm

I`m trying the other way arround. I have a internet connection which should give me IPv6 (and it does when i use the modem as normal) but i wil not get an ipv6 range on the pppoe interface from my provider

raymonvdm

This week my ISP connection changed from a broadband router with routed subnet to a router with a pppoe connection. In the past i was bridging my ether4 interface (ISP) with a vlan4 interface (which holds my VM servers) to use a public ip on vlan4 Since i changed from ether4 to PPPOE interface i`m u...

raymonvdm

I`m using this on a ip base but port base should also be working Ether1 = LAN Ether4 = ISP1 Ether5 = ISP2 I`m not shure how i did it because my wiki is lost But i know some of the steps IP -> routing Create a default route for ISP1 distance 1 and routingmark 2isp1 Create a default route for ISP2 dis...

raymonvdm

I think it can only be used when connecting to MT boxes using a PPTP/L2TP/PPPOE connection http://wiki.mikrotik.com/wiki/Manual:BCP_bridging_%28PPP_tunnel_bridging%29 I was running a bridge on eth3 and vlan4 but my internet connection change and now i need to run the bridge on pppoa interface and vl...

raymonvdm

I noticed that my RB450G is running at a temp of 92 degrees

and a voltage of 13.3 Volt

raymonvdm

First i will be trying to contact diswire to get me a RB450G because i seem to stumble againt cpu speed issues on the RB192

However it is working for know i`m very unhappy with the speed. Als when i replace my Solcon connection with the Ziggo connection the RB192 seems to hit the roof

raymonvdm

I already tried to find out what went wrong using torch. But i did see the traffic going out interface Ziggo, But i also did see the connections go out inteface Solcon But now it seems to be working if i enable and disable the following rules. For the connections to be successfully marked i need to ...

raymonvdm

I stil cannot get it to work Traffic incomming on solcon interface is comming in and going out on the solcon inteface (This Works) Traffic incomming on ziggo interface is comming in and going out on the ziggo interface (This Works) But when i want to redirect al port 80 trafic to the ziggo interface...

raymonvdm

I don`t know what i am doing wrong because it still isn`t working. Even when i disable the passthough option of the mangle rules it still is not working. I may have found another issue, when i ping from the outside world to the Ziggo ip the traffic is comming in on interface "Eth5 - Ziggo WAN&q...

raymonvdm

add action=src-nat chain=srcnat comment="Ziggo Outgoing" disabled=yes dst-address-list=!NO-SRC-NAT src-address=192.168.110.0/24 to-addresses=xx.xxx.175.32 add action=src-nat chain=srcnat comment="Solcon DSL" disabled=no dst-address-list=!NO-SRC-NAT src-address=192.168.110.0/24 t...

raymonvdm

But on what rules do i need to specify the out interface. Do i need to do this on all of them ?

raymonvdm

add action=src-nat chain=srcnat comment="MiniITX outbound SRCNAT to xx.xx.52.5" disabled=no dst-address-list=!NO-SRC-NAT src-address=192.168.110.200 to-addresses=xx.xxx.52.5 add action=src-nat chain=srcnat comment="MCE outbound SRCNAT naar xx.xxxx.52.2" disabled=no dst-address-li...

raymonvdm

Hi, I also trying to estaiblish a dual wan router using mikrotik, I`m using a RB192 for 3 years now and am trying to add a secondary cable interface using the example in this post Here are my settings: 7 ;;; Mark connections to go out of Ziggo chain=prerouting action=log protocol=tcp dst-port=119 lo...

raymonvdm

I just bought a Cobalt Qube 3 to install Mikrotik on using a IDE Flash module but i am not sure if it wil ever work because the Qube uses a special bootloader. Has anyone succesfully used a Cobalt Applicance using Mikrotik? Tonight i will try to restore the cube tot the Sun default installation afte...

raymonvdm

Hi, I have a RB192 connected to SIXXS using a 6-4 tunnel. This is working fine. But now i want to protect the clients on my lan from being connected from the big ipv6 world. However al that im trying isnt helping [admin@mt2] /ipv6 firewall filter> print Flags: X - disabled, I - invalid, D - dynamic ...

raymonvdm

Hi,

I found a FireBox Edge X5 can somebody tell me if i can install Mikrotik in this device. The device lacks a CF-Card so i cannot install tru cf cards

raymonvdm

Is this really working ? I still have a Raq4i with no function so far

Is the display also working ?

raymonvdm

Im trying to build a tunnel from a Nokia E71 tot an MT3.18 (RB192) But all i get on the MT is a warning: IPSEC: could`t find configuration. I created the following VPN policy using "Nokia Mobile VPN Client Policy" IKE: Ike mode: IKEv1 main Authentication: PRE-SHARED Identity type FQDN Iden...

raymonvdm

I just want to create hotspot on both RB192`s. The both have a DSL connection for internet. And VPN to eachother to create a local net over wan.

raymonvdm

Hi,

I currently have two RB192`s and would like to add wireless to them. But what card do i need to choose. For now i have a loose accesspoint. Is the R52 possible in the RB192 ?

400mW wireless is nice i think. But can the RB192 give this much power ?

raymonvdm

I just asked my supplier if he has one on stock.

Would like to know the speed difference. For now i got 2 RB192 for VPN / WAN / NAT. But on one location i would like more speed on the router.

raymonvdm

I`m trying the same thing. @work if have an OpenVPN server. On my ubuntu notebook ik have an OpenVPN tunnel to the work. Now i`m trying to import the .key file using the sharedsecret. This is succesful but when i select the certificate on the connection winbox gives me the following error Couldn`t c...

raymonvdm

Hi, Today i upgrade my RB192 from V3.3 to V3.5 and now i`m unable to make the L2TP connection (keeps on dialing) PPTP connection to my other RB192 is ok. Are the other boards with similar problems after an upgrade to V3.5 Im currently waithing for al SIP channels to clear so that i can downgrade to ...

raymonvdm

Hi, Last night i upgrade my two RB192 with V3.0 software (from 2.9.50). And today i found out that my sip calls all have one way voice. I have one RB192 at home with my parents. It shares the DSL connection. Hosts the Asterisk server. And connects the wireless bridge to the network. At my home it ro...

raymonvdm

I just upgrade 2 of my RB192

One with no errors peeks a 100% at some times ( Ros 3 bug)
Buth the other one peeks at 100% fulltime and now is lost.

First upgrade from 2.9.48 to 2.9.50 and the 3.0

Will try power switch tomorrow (RB = 130km away)

raymonvdm

Contact MT support.

You may have to send in your IDE Flash but i`m almost sure you will get you replacement key. I have read it somewhere in the past on MT website/forum

raymonvdm

Hi, I have found a " Setting static DNS record for each DHCP lease " script on the Wiki BUT I have serveral different DHCP Server with different IP ranges. But the script adds only one domain name to alle different leases. How do i make a difference betwean the different networks dhcp.lan....

raymonvdm

Is there a routerboard which does support higher bandwith ?

I just dont understand the bandwith test results MT gives us. Am i getting everything out of the board the way im using it now?

raymonvdm

Just enabled connection tracking but disabled FTP Service Port These are the results. Copied (17-11-2007 20:00:27): ftp://192.168.200.200/home/beheer/100mb.bin -> c:\100mb.bin 104.857.600 bytes, 2980.5 kbytes/s Copied (17-11-2007 20:01:41): c:\100mb.bin -> ftp://192.168.200.200/home/beheer/100mb.bin...

raymonvdm

Just disabled "connection tracking" and here are the results - Internet connection lost (SRC-NAT no longer working) Copied (17-11-2007 19:54:08): ftp://192.168.200.200/home/beheer/100mb.bin -> c:\Documents and Settings\ladmin\Bureaublad\100mb.bin 104.857.600 bytes, 2934.6 kbytes/s Copied (...

raymonvdm

Hi, I recently purchased 2 RB192 devices. For PC replacement 1 Board on an 10/1 Mbit ADSL <-- This board is 150km away 1 Board on an 15/1 Mbit ADSL <-- This it the board currently testing Now i found out the when i place an MiniITX based Debian server on an interface that i wil name DMZ. The FTP tra...

raymonvdm

Does Mikrotik have trouble with download locations. Maybe i can talk to my ISP to obtain a download area for Mikrotik. It will be located in The Netherlands if i can get it aranged.

raymonvdm

I have followed this how to http://www.mikrotik.com/testdocs/ros/2.9/interface/eoip_content.php#5.19.3 But it is not working I have a pc running mikrotik 2.9.39 (MT) and a routerboard 192 running 2.9.46 (MT2) - I have created a pptp-dial-in on the MT 192.68.70.250 for local and 192.168.70.252 for re...

raymonvdm

Can you please give me a Cam first

Are pictures also allowed?, i would like to get my hands on an level 4 license.

raymonvdm

I just bougt an D-LINK DEF-570TX on Ebay 4 years a go. Its the version with the 4 Intel NICS on board an it is :lol: . Also scavanged for an 2 port Compaq NIC (2 Intel NICS on board) at work. Using these boards together with an ISDN BRI interface on an Compaq EN SFF (3 PCI Slots) and a CF-IDE conver...

raymonvdm

I think u could use this sollution. But its based on a single MT box.

But maybe u can do this

http://wiki.mikrotik.com/wiki/Load_Balancing

raymonvdm

Hmmm im not sure that i understand this solution but i have the same problem. But my network is a little more "advanced" i think. The Story: I have a SFF Desktop running an Dual Port, Quad Port and Single port NIC. The Quad port is connected to my ISP. 4 x Ethernet -> DSL Modem. To obtain ...

raymonvdm

I think for now u must use a 3.5" HDD or a 2.5" HDD Hmmm, MT is thinking about you What's new in v3.0beta1: *) added support for SATA disks; *) added initial support for SMP on x86; *) added support for up to 2Gb of memory on x86; *) fixed time matching in firewall rules; *) added time mat...

raymonvdm

Isn`t this a problem with the powersupply of the board ?

I thought that more people where experiencing problems with multiple RS5`s

raymonvdm

i disabled all mikrotik's firewall rules... and .... :roll: everything is ok in the last hour :lol: i will monitor the connection a couple of hours and then i will turn on rules one by one and see which one is disturbing... Thank you savage for your help... and then i will post the annoyance firewa...

raymonvdm

I found out something that worked ip route 0 A S 0.0.0.0/0 r 84.245.4.1 0 4-1 BBNED chain=srcnat out-interface=4-1 BBNED src-address=192.168.100.1 action=masquerade Changed it to chain=srcnat src-address=192.168.100.1 action=src-nat to-addresses=x.x.4.233 to-ports=0-65535 And it started working. I`m...

raymonvdm

Anyone ?

raymonvdm

Hi, Currently configured a MT 2.9.39 with - LAN Interface 192.168.100.250/24 - WLAN Bridge interface ( linksys bridge) 192.168.50.250/24 - DMZ Interface (not used) 192.168.13.250/24 - WAN1 x.x.4.234 - WAN2 x.x.4.233 - WAN3 x.x.4.231 - WAN4 x.x.4.232 The wan interface al have a static DHCP ip bound t...

raymonvdm

http://wiki.mikrotik.com/wiki/Load_Balancing

raymonvdm

helpppp, somebody make a guide plz.
it seem tobe i'm doomed

Try this but with the ports for warcraft 3

http://wiki.mikrotik.com/wiki/Forwardin ... nternal_IP

I think this is what you mean

raymonvdm

Me Again. I have replaced my MT box with another box. So that i could add another NIC (Extra PCI Interface). So i added a Dlink DFE570 (4x 10/100) to my MT Box. Now i connected my DSL modem to an extra switch and from this switch i connected 4 cables to my 4 port nic. And voila 4 ip adresses from pr...

raymonvdm

No sorry realy meaning LBA

raymonvdm

Hmmm Im trying to run Mikrotik 2.9.39 on my CF-IDE 512MB Dane-Elec flashdisk again. - I installed using a USB Cardreader and the netinstall utlity - Placed the CF in my MT ( no boot) - Changed Bios harddisk mode settings from auto to normal and boot was fine - Changed Bios harddisk mode setting from...

raymonvdm

will this be possible in the future ? I kind of need it for

http://forum.mikrotik.com/viewtopic.php?t=13267

raymonvdm

I found out that when i add the WAN interface into a bridge an wil give th bridge a virtual mac adres i can obtain a extra ip adres. But how do i add the other 2 ip adresses. Because an interface can only belong to one bridge ?

raymonvdm

Hi, Ive contacted my Provider TweakDSL who is using BBNED (Netherlands) they can give me multiple ip adresses (maximum of 4) but how do i connect this to my MT ? The modem is configured in bridge mode, so i need to give up 4 mac adresses to get the 4 ip adresses. But my WAN interface only has one MA...

raymonvdm

Hmmm mayby im experiencing the same errors with my 512MB Card.

Although it worked the firsttime Is this problem fixed in some later version ?

raymonvdm

I have used a Dane Elec 512MB CF drive for some time. But the drive became unreadable do to some unknown reason. So i changed back to my 6 GB Harddrive In the meantime i found out that the cartonboard i used to place the cf flash ide converter on got a litte wet So the CF was shorted out. But am usi...

raymonvdm

Enable Proxy ARP on the local network interface

raymonvdm

When i add the following rules to my mikrotik. I still can connect to the server with ssh. I have created and interface called 2-4 DMZ. And am dropping everything accept icmp. Why can is still use putty to connect to 192.168.13.200 (CentOS Box) 0 ;;; DMZ Regels chain=input in-interface=2-4 DMZ dst-a...

raymonvdm

Hmmm

Problem solved.

Under PPP - Profiles and then the used profile there is an option

Change TCP MSS ( in this profile set to no) after setting to default or yes everything is working fine.

raymonvdm

Hi,

I have a Mikrotik running on a Celeron 400 with 128MB of memmory. Using a DSL connection for WAN.

Now when a users connects vpn trough pptp they are unable to browse the web.

All traffic is allowed and trace/ping is working. But browsing not

raymonvdm

I found this. But will this work with my NAT setup ? Try something similar to these\ /ip firewall mangle add chain=prerouting tos=184 \ action=mark-packet new-packet-mark=voip /ip firewall mangle add chain=prerouting src-address=192.168.100.44 action=mark-connection \ new-connection-mark=voip passth...

raymonvdm

Hi, After installing a trixbox voip machine behind my MT router i noticed that the voip stutters if some else starts a download. How can i fix this.? My MT box has 4 interfaces WAN - Which connects to the DSL modem 10.0.0.250/24 XS4ALL - Which is the internet connection actualy LAN1 - The interface ...

raymonvdm

Yes up and running again. It seems tha my CF IDE Flashdrive has died. Although windows xp can read and write to the flashdrive. Something isnt working fine. Sow now i have removed the CF-IDE Converter and the CF-FlashDisk from the machine and installed mikrotik using the BootCD on a Harddisk and res...

raymonvdm

- New network not helping
- Latest netinstall utility also not helping
- Installing the software on the compact flash using a usb cf reader on mij XP machine isnt working either.
- Installing o a normal HDD, same problem

Help

raymonvdm

Same Problem with me...

http://forum.mikrotik.com//viewtopic.php?p=53288#53288

raymonvdm

I have a Compaq EN SFF machine setup as mikrotik router with a CF-IDE Converter and a compact flash card. Because of switching DSL providers some day now, ive installed a ISDN Board. To get on the net when mij dsl connection is being moved. So i powered down the box and installed a ISDN board. But a...

raymonvdm

After almost one year of happyly using MT the last update finaly fixes the link detection issue with my networkboard ( dlink DFE-570TX )

Thanks

and keep up the good work!!

raymonvdm

Are u just using a simple nat setup ?? After you read this http://www.mikrotik.com/Documentation/rosmE.pdf I cannot find the rule setup in the manual and i cant easily find the manual part of it. But u should make a dst-nat rule under ip -> firewall using winbox that forward tcp port 25 to your mail...

raymonvdm

Ive found this example in the 2.9 docs i think this is what you need ?? Application Examples Description The following section discusses some examples of using the mangle facility. Peer-to-Peer Traffic Marking To ensure the quality of service for network connection, interactive traffic types such as...

raymonvdm

i`m also experiencing this bug using a dlink dfe 570 4 port card is there any way how to solve this problem ??

It is using the FX/TX DEC21140AF Driver but i thouhg in the past this was working perfectly

raymonvdm

I was downloading some stuff from my ftp server today and saw that the connection was lost (download fails/stops) But this time i got a syslog report: Maybe some one find the error ?? The 10.0.0.138 is my Thomson Speedtouch 716 Modem. The 10.0.0.150 is the MT WAN Interface The 192.168.100.250 is MT ...

raymonvdm

by the way, does MikroTik support Dlink DFE 580TX 4-port? in the manual it says not recommended...however i want to use it. is it possible?

Im using the DFE570TX 4 port and is working fine, the only problem is dat MT doest see a link up or down. it always says link up

raymonvdm

my mt are working now to and i havent done anything at all?!!!? and i have the same problem as you with my adsl line but in my cace it is the adsl line that are the problem, i have drop outs eaven if i connect directly to my modem with my computer. regards leo hmmm maybe this is the problem with me...

raymonvdm

Als upgrade from 2.9.8 to 2.9.10 and i have no problems here so far. Im only using one pptp client at the moment ( WinXP Professional) to reach my internal network behind the mt box from outside. I do how ever have a drop connection error on mij pptp client and on mij ADSL Connection but this proble...

raymonvdm

Now i have a new idea but im not sure how to do the scripting IDEA: ping the ADSL interface every minute and when it fails open up the ISDN dial up connection until the ADSL interface is up and running again. The ADSL and ISDN interface are both provider interfaces and the MT is only used for intern...

raymonvdm

Install

- ISDN Package and Telephony Package

But i installed the full package ( i thougt but apparrantly the isdn and telephony was missing)

Installed and just need some testing for now

raymonvdm

Hi, I the past i had the ability to use my isdn card in my mikrotik os. But today when my ADSL connection failled i noticed that there no longer an ISDN BOARD is deteced and i also lost the VOIP abbility Is this a know issue ? When i try to add the driver using driver add name=ws6692 it does fale Wh...

raymonvdm

Some Networkproviders support email2sms. So it is possible to let MT send an email 2 your provider and the providers sends the email to your cellphone in sms format

I`m using this setup for monitoring 50 servers using HP Systems Insight Manager ( which uses email for alerts)

raymonvdm

Hello, I`m having some problems reaching some sites on mij network like myaccount.voipbuster.com (ping works no page comming for 2 days now) http://www.mikrotik.com/docs/ros/2.8/ (not working / mikrotik.com works fine) Now i want to setup an isdn dial up link to my provider but its not working Im us...

raymonvdm

I think i have got the same issue here, Trying to get the hotspot to work but never got a login page, after deleting al dual firewall rules and some reboots i get the login page ussing http://ipaddress/login.html but the script isnt running. On a windows XP box however the page is running nice, but ...

raymonvdm

Hi,

Please build in usb display support for CrystalFontz CF634USB

Ive got one for my Mikrotik Router but no support yet

raymonvdm

Helping myself, Found in the docs, after i searched for the second time :-) Do not forget to set the e-mail settings, i.e., the SMTP server and From: address under '/tool e-mail'. For example: [MikroTik] tool e-mail> set server=159.148.147.198 from=SysAdmin@host.com [MikroTik] tool e-mail> print ser...

raymonvdm

Using script examples gives me a mail error.

How does MT finds out which mail server 2 use ?

Error sending e-mail: error connecting to server in 19-Feb 20:29:5.49 from 192.168.100.250

raymonvdm

Maybe adres space issue with the onboard nic?

Already tried swapping pci slots ? or disabling the onboard nic ? Bios upgrade ? IRQ adressing settings (for as far as the are available)

raymonvdm

I`m using a speedtouch 510 adsl modem, and my MT box is pptp dialing over that for a internet connection. I live in the netherlands. There are some people playing with Static IP Spoofing (Router gets public ip) but i did not test this setup with mikrotik (yet) http://www.speedtouch.com/prod510.htm I...

raymonvdm

Maybe a BOOTP versus DHCP Issue ?

raymonvdm

After Removing NIC Express from my workstation and reinstalling the Cisco VPN Client everything works fine.

raymonvdm

When i got home this evening i had my work laptop with me, when i plugged in the cisco aironet wlan to connect it to my wlan which is connected to my MT-Box every thing works, Gave up a static ip because i forgot to config dhcp and after this i just connect to Cisco VPN without any problem. So i thi...

raymonvdm

Nope it is still not working

- Changed ARP from enabled to proxy-arp
- Reboot MT
- Still not working

Anybody Else

I`m using PPTP for connection to my DSL provider and want to connect over the pptp connection to my work using cisco vpn client

raymonvdm

Hi

Im running mikrotik router since this week and now i cannot connect to my work VPN connection like the packets never leave my mikrotik.

Is this an known issue or do i have to setup rules for this, i cant find anything for VPN Pass-Tru

Search found 162 matches