MikroTik

LSan83

I’ve set up to capture the 1 3 7 20 bands. I wanted to know if there are terminal commands to do an aggregation of 2 or more bands as primary to increase the flow in mbps It's full automatic. I use Chateau with Wind3 too, and the 3CA (inside the list of allowed bands) always works (i reached 180 do...

LSan83

Maybe... I hope the roadblock isn't for Covid problems in the team.

LSan83

Any ideas? Does the RouterBOARD just not have the grunt to sustain these speeds? Normally i wouldn't be all that bothered but i've bought it specifically to get the absolute most out of my fibre connection, which as you can imagine is fairly expensive! Just wrong model. The Hap AC2 (ip4018 arm quad...

LSan83

Does Mikrotik has any roadmap to implement WPA3 in 2021?

They already do it. Wpa3 is on wave2 optional driver for ros 7.1beta3.

LSan83

Everything is better than WAP LTE internal antennas. LHG is a lot better on B20 too.
Or you can install good external antennas on wap lte.

LSan83

Don't count exactly the seconds. Checks the led's blinking scheme instead. On my Wap AC is less than 10 sec.

LSan83

Almost every device out there based on ipq4018/4019 has atleast 256MB of RAM. With a few exceptions, like RT-AC58U which struggles to not throw errors because of the very limited memory available out of the 128MB total. So I wouldn't keep my hopes up to see it running in the future on lower require...

LSan83

!) added new experimental wireless package "wifiwave2" for ARM devices with more than 256 MB of RAM (CLI only); What about devices with 16MB storage and 128MB of RAM? This new driver is way too big. 10MB. Does this mean that IPQ4018 devices are left behind? And the IPQ4019 devices with 16...

LSan83

Better if you set 802.11g/n on 2.4 Ghz and 802.11n/ac on 5 Ghz at least.
It's normal that you can't ping external ip from inside your lan. If you don't ask at TIM a public ip, you can't reach your network from outside neither.

LSan83

Hey, is there anyone who owns a Chateau LTE12 and is able to use LTE mode only? Currently I'm able to connect to internet only using 3G mode. I'm in contact via Mikrotik support and I'd like to know if someone else is experiencing the same problem. Here i am! I always use LTE mode only on Chateau L...

LSan83

I agree it would be more honest to explicitly say in the product brief "this product comes with beta software which is only infrequently updated but has many known issues". Customers can still decide if they want to get it. Loyal MikroTik customers probably would, but new customers could ...

LSan83

However, on my iMac these channels seem not available for use on AirPort.
So what is the actuality with these channels? Yay or nay?

Not only iMac... A lot of client don't support all allowed 5Ghz frequency. If you have some of them on your network then you have to exclude some frequency.

LSan83

There is already the Chateau LTE18 (4.5g cat18) and soon the Chateau 5G (with 4 and 5g modem).
They're using Quectel's modem in LGA form factor.

LSan83

I reached 190 Mbits with Chateau LTE12 with poor signal reception because i haven't free line of sight (woods).
If You can't get over 110 is for your ISP or for poor reception.

LSan83

I haven't set antenna gain manually, tx-power-mode is default. So it reads the country settings from eeprom which is correct. With 6.47.1 antenna gain should be set to default (for WAP AC should be 2 dbi for both 2.4 and 5 Ghz). With antenna gain set to 20/23 dbi the signal is underpowered by 18/21...

LSan83

Is this an hardware fault or a software problem? Anyone with this problem before? it's very strange... ISP: Iliad Italy I'm using the Chateau with an old 3 Italia's SIM on Wind3's new network. The 3 CA is always on. Sometimes the primary band switch between B7/B3/B1 but the connection don't drop do...

LSan83

Stupid question: You have connected the external antennas with coaxial cable?
Lte internal antenna on Mikrotik are weak.

LSan83

Write to support. The first firmware for Chateau on the repository is the 7beta08. https://mikrotik.com/download The 7beta06 preinstalled from factory isn't on download page. You have to upgrade the firmware of the lte modem from version 04 to 06 too. I don't have problem with Chateau on 7beta08 (pl...

LSan83

Hi!
Today i just got a Chateau LTE12 and I upgraded it with ros 7beta08.
When i try to update the modem firmware i found there is a new version (EG12EAPAR01A06M4G) but after the download i get an error that it can't upgrade the firmware.
What i have to check?

LSan83

Hi!
I just bought Chateau lte12 too, and it worked on my Wind3 sim with firmware 7beta08 and modem firmware EG12EAPAR01A05M4G.
How do you upgrade modem firmware? i always get an error after download it.

LSan83

Check here: https://www.varia-store.com/en/produkt/ ... ap-ac.html

They are selling it through ebay too.

LSan83

I'm using WAP AC on the walls and they work very well. I don't have CAP AC to compare (i founded used WAP AC at a good price... Easy choice

).

LSan83

Its just in the center of the apartment Most of the wifi devices are in the radius within 10 to 20 meters from the router. I had a feeling that hEX s is the mosr powerfull of the 3 compared to hAP ac and hAP ac^2 isn't it? No, it is in the middle. HEX S has about half the "power" of HAP A...

LSan83

You have connected the wAP to the Hap AC2 with a ethernet cable right?
The guide you linked is for a network of AP connected with cable.
If the radio on Hap AC2 is configured as CAP connected at the same CAPsMAN server of the WAP, both use the same configuration.

LSan83

Webfig is ok for normal configuration (but when you mess it, only Windows tools like Winbox and Netinstall can recover the hap). The important thing is to never use quickset after initial setup. If you change anithing in Quickset after you get in trouble. Use only Webfig and Terminal for tuning and ...

LSan83

And here's the test done in the morning. As I was saying... Results morning.png Severely disappointed. I'm ready to return this device if there's no way to fix it til Monday... If the integrated antenna of WAP AC R are the same of the old WAP R they are weaker than the integrated of B525. I used bo...

LSan83

Kinda kills it as a replacement for unifi. If the path to the device manager goes down for some reason, you really don't want all the APs to go down. That doesn't mean the internet is down. Just rebooting the manager for an update shouldn't kill all the APs connected. You can have multiple CAPsMAN ...

LSan83

I have spend a lot of time on the UBNT forum, mostly helping others. I think that forums in common are the best resource for solving problems. Especially because you get support from a community. And not only the community, there are some MikroTik employees giving good information as well. I believ...

LSan83

Yes, you can use switch of other brands. If you need VLAN then you need a "smart switch" that can manage them.
In my network only the switches aren't Mikrotik (i already had them from the previous network) and Capsman works well.

LSan83

Do any MikroTik wireless access points offer near gigabit speeds? No. And remember, that normally Mikrotik provide max 50% of spec -s speed. ? I reach the full standard speed with wAP AC under CAPsMAN and 1x1 802.11ac clients (433 - overhead = 300 Mbits half-duplex in tcp connections). Of course fu...

LSan83

Hi Guido!
I use R11e-LTE on Wind3 in Italy. It's not an eSIM modem.
It need a external reader for a normal SIM (usually a full-size SIM in the Mikrotik device that are ready for it, like the WAP R, WAP AC R, LtAP R, LHG R, ecc ecc).

LSan83

In the last try a full reset of the device. I had a few problem with some used wap ac (with same configuration of other wap ac i have) and the reset has resolved all of them.

LSan83

/interface wireless security-profiles set [ find default=yes ] supplicant-identity=MikroTik add authentication-types=wpa2-psk group-key-update=1h management-protection=allowed mode=dynamic-keys name=xb supplicant-identity=MikroTik wpa-pre-shared-key=xb wpa2-pre-shared-key=\ xb /interface wireless s...

LSan83

Try to put the wan for the modem on another port. Perhaps that port is broken.

LSan83

Hi, I am looking to get a new Router for my new smart home where I plan to separate all IoTs, computers and guests using VLAN. I want this router to: - provide IP for a minimal 500 clients (there are almost 250 smart bulbs alone in this house, not to mention smart plugs, etc) - 1G fiber internet to...

LSan83

Hi there i have mikrotik hap ac and move to a bigger house wifi just suck I waill add tp link m4 to mikrotk and use mikrotik to be a router with vpn and tp link m4 is dealing with all the wifi. did you have this setup? What can you tell me about it? did you set your tp link as AP and mikrotik as ro...

LSan83

Maybe yes Maybe No. All device with RouterOS have complete software features, but the switch (like CRS328-24P-4S+RM) are "slower" for firewall/router/captive portal use... Look at the performance in datasheet for an idea of the speed. If it isn't enough for the speed of your internet conne...

LSan83

Okay, I just upgraded to 9260, there is night and day difference. Local transfer (of a shared file) on the 2.4GHz network is at 20-22 MB/s which is 160-180 mbps Local transfer (of the same file) on the 5GHz network is at 50-55 MB/s which is about 400-440 mbps After all thats been said, if I underst...

LSan83

Hi, here in Italy both WAP LTE and LHG LTE with standard Mikrotik modem work very well.
I reached stable 95-100 Mbits data transfer without problem (on 20Mhz B3).
Perhaps is a problem of your country's mobile operator.

LSan83

Hi,\ I was looking at the current Mikrotik routerboard lineup and am a bit confused on what to go for. I am looking for what is essentially meant to be a powerful 2.4 and 5ghz router for a somewhat large-ish home, the materials of which don't let wifi signals through very well. I'm ok working with ...

LSan83

You will need to post an export of your CAPsMAN as well. And also it would be helpful if you post an export of a working CAP. This is my working config. CAPSMAN on HAP AC2 # aug/28/2019 21:40:25 by RouterOS 6.43.16 # software id = V4ND-FL2U # # model = RBD52G-5HacD2HnD # serial number = 8FDE09BFD2C...

LSan83

On the Mikrotik console I set the PoE Out to "Auto On" and also on "Forced On", but still nothing on the Unifi. I'm starting to wonder if this would not be a PoE incompatibility problem between the hAP ac and the unifi ? Is it supposed to work or do I need to by an additional Po...

LSan83

Do you use CAPs Man Forwarding or Local Forward?

I'm using Local Forwarding.

LSan83

After another day of investigation, I did not find a way, how to do it. I got another wAP, put it to other CAPsMAN controlled installation - the same problem... Could it be some HW issue? Is there anyone who has the wAPG-5HacT2HnD sucesfully runing in CAP mode? Or what model do you use to cover out...

LSan83

I have no personal experience with using those APs but they should be OK for that kind of performance. The RB952 is a combined router, switch and AP with good overall performance. As you don't need a router there you could also consider a separate small switch and another cAP AC. Or use a HAP AC2.....

LSan83

I used one WAP LTE with a third party panel antenna (9 dbi for LTE800, around 14 dbi for 1800-2600) for last year. The 2dbi integrated antenna is too weak.
Now i changed it with a LHG LTE and i see an huge improvement (i live in countryside and the bts are far and behind woods).

LSan83

Have you considered Powerline?
PWR-LINE e PWR-Line AP can use the eletric grid to expand your wifi. Or you can wait for Mikrotik access point with mesh (Audience) announced last March ( viewtopic.php?t=146191 ).

LSan83

everytime 5G wifi crush, the router reboot, and the log first line is : "router was rebooted without proper shutdown." I had that message too on 1 of my 3 WAP AC.... It was unstable (lag, webfig not reacheable, ecc ecc) because the power adapter (24v) was too weak for the lenght of the ca...

LSan83

How did you remove ethernet interface from router? Physically? Then I doubt if you can connect to your router :-) Do you have more eth interfaces? What router it is? Configuration? He use a CPE on the roof as a router and now he has 15 inches of snow around the CPE :D Wrong configuration in the wro...

LSan83

So all in all, which would you prefer, the HAP AC or AC2 for a home (concrete house) scenario? HAP AC2 (better cpu for CAPSMAN) plus some wired connected WAP AC . I'm using HAP AC2 with three WAP AC (triple chain with outdoor case) in my house. CAPSMAN roaming works well for me. I have 10-15 device...

LSan83

Hi guys i want to know if the RB4011 support dual WAN or not if yes, please tell me how to do

Sure, all Mikrotik router does multiple WAN.

https://wiki.mikrotik.com/wiki/Manual:PCC

LSan83

The router is equipped witha Category 4 modem for speeds of up to 150 Mbit/s but have one Ethernet port 10/100. The question is, if the lte modem can get 150 Mbit/s how can i use them if ethernet port is 100 Mbit/s? Simply you can't. You are limited at 100 MBit/s... This is not a problem, a 150Mbit...

LSan83

Thanks for the info, but Unlimited Red+ seems to be smartphone only, and I have no luck to find any info on 3Unlimited. For Italian law, you can use the GB of any mobile plan as you want. You can use sim for smartphone for tethering and modem without problems. https://www.ilsole24ore.com/art/tecnol...

LSan83

Hello. Well you'll not find any unlimited from our major carriers (vodafone..tim..TRE/ Wind). But there are some company which are selling internet service using our carriers nets. It's not true! Only TIM don't have unlimited data plan. Vodafone have Unlimited Red + WindTre have 3Unlimited Both the...

LSan83

http://srv1488.microhost.com.pl/modem_test/mikrotik5.png Huawei B315s-22 had better RSRQ inside building placed far away from BTS. Is my Mikrotik broken? May I make a complaint to have it repaid under the warranty? . . Sadly if i do changes on LTE interface (like disable bands) the modem don't conn...

Search found 55 matches