MikroTik

elkolo23

Test from 912 to 912,, no other equipment between them.

elkolo23

now overclocked

elkolo23

why not try overclocking to 720mhz.

elkolo23

today received couple of 912 outdoors

here the results at 12kms.

tomorrow ill post 65kms with 34db rocket dish.

elkolo23

link type point to point...
bitrate just shows for 1 sec and then stops....
definetly something is really happening...
versions affected routeros 3.23-3.30

elkolo23

i just fixed it by adding the dude package to the routerboard.. then in dude interface in widows just clic on the device and check where it says dude server..

i just started working again...

elkolo23

currently i have a problem,, ros 3.9 on a xeon 2.4ghz with multuicpu disabled. it happends that with some customers suddenly it stops surfing... i check with pings from their pc to the mikrotik router and it responds nicely..but its not surfing.. what ive donde is to change ip address... and its sur...

elkolo23

the problem is not at my mikrotik server,, is at my routerboard ap

this ap has no firewall....
no nat

elkolo23

i found out theat the problem is behind routerboard ap and not mikrtik router....

my ap is a router board 433

ethe1+wlan1+wlan2 are bridged

the bridge has 192.168.50.199/32 ip address
no firewalll no filter rules...
no queues
just bridging not as router
no nat

elkolo23

another thing is that when i connec from the office were the mikrotik is located i can use outlokk prettywell
but at home or at customers pc no...
accespoint is rb433 with ubiquitis sr5
cpe ubiquitis nanostation5 in station mode
everything works as bridge not routers

elkolo23

the only way i noticed ports are opened is when i add them as part of the web proxy(3128+25+110)

elkolo23

i need to enable 25smtp and 110 pop3 ports... mk wont let me use outlook

elkolo23

currently i have issues with my network using outlook i have already opened ports 25 and 110 also 587 behind my mikrotik server... everything works ok when i plug cables to my mikrotik lan.. the problem starts when i log behind my cpes.... my networks is as follows MK(XEON MACHINE,, BANDWIDTH AND RO...

elkolo23

i have a problem with an rb532... it happends that my cpes can only connect to it in station wds mode,,, and when i try just station mode it wont work...

ap rb532 with cm9
cpe ns5 ubiquiti

elkolo23

i have just configured my 532 as ap bridge and in wireless table i have several cpe associates but i cant ping or communicate to them... my ip address for radios is 192.160.50.0/24 am not sure if i need to bridge ether1 with wlan1.. i know alot people there has done this,, please help me a bit best ...

elkolo23

ANY HELP I CAN PROVIDE YOU,,PLZ CONTACT ME AT LUISOSA50@HOTMAIL.COM... CURRENTLY LIVING IN EL PROGRESO, YORO...

elkolo23

AM HAVING APROBLEM,,, MY WISPO IS GROWING REALLY FAST AND AM HAVING PROBLEMS ON MANUALLY MANAGING BILLING AND PAYMENT FOR CUSTOMERS....
ANY IDEA ON HOW TO SIMPLIFY THIS..

BEST REGARDS

elkolo23

please post detailed config..
looks nice

elkolo23

currently i have set my webproxy and is working correclty,, but i want to add a parent proxy which would be a cacheflow(bluecoat systems)... currently my setting is as folows.. MT VERSION 2.9.44 WEBPROXY enabled: yes src-address: 0.0.0.0 port: 3128 hostname: "proxy" transparent-proxy: yes ...

elkolo23

IS THER ANYWAY ON CONFIGURIN 2 MT
ONE AS ROUTER AND PACKETSHAPPER AND THE SECOND ONE AS A WEBCACHE??

if yes any guides..

elkolo23

PLease check my post parent proxy not reaching mt back

elkolo23

Hola,, estamos para ayudarnos,,, dime que podemos hacer por ti

elkolo23

currently i have set my webproxy and is working correclty,, but i want to add a parent proxy which would be a cacheflow(bluecoat systems)... currently my setting is as folows.. MT VERSION 2.9.44 WEBPROXY enabled: yes src-address: 0.0.0.0 port: 3128 hostname: "proxy" transparent-proxy: yes ...

elkolo23

how would you send requests to squid proxy??? just add parent proxy and type squids ip address?

elkolo23

could you post config please

elkolo23

my cache is a CACHEFLOW SA725.

i need to send request to it,,,, do i need to set as parent proxy?

elkolo23

would like to redirect http request to a webcache server i have,, would like anybody coulld help in config steps an tips

best regards,, thanks for your time

elkolo23

i currently have 2 nics
1 public interface
1 private interface

now i need to add another nic which will have public ip...
so i want to have 1 nic whith private nat generated address and 2 nics (190.x.x.18-190.x.x.19)
.18 for internet browsing
.19 for voip

please help me out with config..

elkolo23

v2.9.46 to 3.0rc6

elkolo23

ok found out that is limiting http perfectly but ares run alot over it limits,,, seems v3 is not shapping p2p connectons.... something which doesent help cause v2.9 shaped averything no matter connection type customer couldd not downlod faster than teir maxlimit... something which is not working now...

elkolo23

Would like more info about layer 7 and how could it help us specially for p2p

elkolo23

I have the same problem with upload in simple queues (latest 2.9 release). Ares reachs more than 100kbps, no matter the max-limit configured. There was some problems with Ares, but since rc5 Ares matching is improved Changelog from 3.0rc5 : *) improved ares/warez p2p protocol matching I believe the...

elkolo23

just upgraded yesterday to v3 and simple queues are not working,,, customers run over their limits and seems to happend when customers have p2p running.

elkolo23

simple quees cant limit p2p,, only http,,, customers with p2p usually download faster than thier limits.
have several customers with max limit 128kbps and are downloading over 512kbps...
this did not happend with v2.9

elkolo23

just upgraded testerday,, everything looks good except for a big problem.,,, noticed quees running over limits... customers with 256kbps running at 512kbps or more.... hten i realized it does not shape p2p,,, only http... will have to downgrade but i tried also several times and this thing wont down...

elkolo23

just upgrade and i have a problemmm,, i have customers which max limit is 128kbps and are currently downloading at 300kbps. it seems its not limiting... something to notice is that those quees are under a parent which has 512/512... but if its limit max is 128 why is it running over it??? in version...

elkolo23

just upgraded to v3 and webproxy is running but no hits are made.

elkolo23

i have configured a parent for home userss which has 512up and down and its named HOME my users have as parent HOME... when i set them everything work nice,, the problem is whe router is rebooted every night (automatically by script) HOME parent is the only one which i can see has traffic,,, all my ...

elkolo23

Which do you prefer,, squid server or webproxy??

personally i have mt webproxy but i ave a friend which has squid machine and it seems to me it runs better..

would like your opinion Normis

elkolo23

what is the max gb supported by mt for webproxy?

i have installed a 180gb but it only recognizes 56gb

elkolo23

i want PARENT A with 512kbps (dedicated) to be shared to beloww 1,2,3,4,5,6,7,8,9,10,11.... users my question is does parent a need ip address? none, blank or 0.0.0.0/0? i tried settin parent a with 0.0.0.0/0 it worked but after router is rebooted it stops workin,,, also i use torch under parent a a...

elkolo23

my proxy is blocked to public,,, the 8080 connection are coming from outside into my router

elkolo23

am currently with a big problem which happends that something is eating my bandwidth.... i used torch and found a lot of 8080 (http-alt) conections which happend to be the only thing strange in my router.. any help will be appreciated since al my customers are mad at me... perhaps i will tell i disc...

elkolo23

nedd help pn using parents to asing dedicated bandwidth and shared bandwidth to users.
also need pcq configuration examples,,what should rate, limit and total limit values be in pcq settings

elkolo23

no bridges interface,,, i did fing a customers cpe which had 10 times pps as the others so i did block him and the problem has gone... now am not sure if virus, spam,, or cpe is the problem.

elkolo23

will like you post which equipments you use along with mikrotik ex (3layer switches, vpn, firewall, cisco.... extrmes, apc ups,solar panels, inverters......

elkolo23

Today i started getting a problem,,, every ip i choose to configure it returns IP CONFLICT WITH ANOTHER SYSTEM....think might be virus or hacker since all ips are not assigned.

please help my network is down.

elkolo23

Today i started getting a problem,,, every ip i choose to configure it returns IP CONFLICT WITH ANOTHER SYSTEM....think might be virus or hacker since all ips are not assigned.

please help my network is down.

elkolo23

i have recently found a spammer on my network...
tried several times to delete virus but keeps coming backk...
what procedures should WISP practice when spammer or virus found behind a customers pc.
what best practices can be done and techniques to do it better.?

elkolo23

it using static ips,no ppoe..
what ive found out something is eating up my upload speed..

i have 3meg down and up but ive noticed it will only displays as 250 o300kbps of upload while 3000kbps download.

elkolo23

Did u disable masquerade or src-nat?
If u disable masquerade or src-nat any massanger wont work

both are working(enabled)

elkolo23

all those ports are open,, it happends that in some computers msn is working and in others not... i did reinstall msn on the ones not working but is the same ...
could it be the ethernet adapter of the ones not working the problem??? coulkd it be possible even though the pc is surfing?

elkolo23

currently i have aproblem which happends to my isp customers,,...- msn messenger is not connecting,, unablke to log in from all my customers computers.. yahoo messenger,skype and all other meesenger applications.. i had noticed days ago that if i limited client connections msn woudnt work.. i did di...

elkolo23

currently i have acquired a cacheflow series ,,, and i would like to use in my network,,,, i am currently usin mt webproxy... 1. i need MT to decide if http request are sent to cacheflow or to public network for resolution.. 2. i need rule hot to redirect requests to cacheflow... 3. would this work ...

elkolo23

it happened same to me could not enter mt homepage,,, message about squid is correct,,oticed the same

elkolo23

my customers do not have MT router,, they use smartbridges brand cpe
they do not use public ip,, they use private nat ip
my ap has 12 clients and i think its cpu runs at 200mhz

noise level is at -100

elkolo23

my ap is a highgainantenas 8186hpmaxx with realtek chip at 800mw and my cpe are smartbridges airpoint outdoor model ..You have customer with some IP, you customer have router with that IP, and customer have network behind router (Cybercafe PCs)?! YES if i set connection limit to 100,32 that will all...

elkolo23

i want to drop in time range but now is not working,, it only drops if i dont put time range

elkolo23

ok my mikrotik is running on pentium xeon 2.4ghz with 1gb memory,,, i have found with torch an ip which has alot of smtp connections on port 25 and i think is not normal as other users dont have this connection.... also what would a resonable connection limit assuming my customers are residential an...

elkolo23

wireless connection

my mk is blockin p2p, connection limit=100/32
also dropping port scanners..

sometimes i lower connection limit but my networks turns slow as a snail so i have to raise it again.

ill try orch and se were the problem could be..

elkolo23

it happends to me that everyday at about 18:00 my pings jump from 10ms to 2000-3000 i thinks it could be p2p so i dropped p2p and it lowered pings but somtimes it jumps agains so messed uo a bit with connection limit from 100 to 10 then to 50 and so on but noticed user could not login to msn and yah...

elkolo23

i have these following rules 15 ;;; drop todo el ares de 4pm a 11pm chain=forward src-address=192.168.10.0/24 p2p=warez time=16h-23h59m,sat,fri,thu,wed,tue,mon,sun action=drop DROP ARES BETWEEN 4PM-11PM 16 ;;; botar p2p de 8am a 10pm chain=forward src-address=192.168.10.0/24 icmp-options=0:0 p2p=all...

elkolo23

equi would you post an example?

elkolo23

i need to divide bandwisth in 2.. i have 2 mbps and i need to separate 1.5mbs for surfing and 0.5mbps for voip... i have nat-masquerade my public ip in my interface.. i was thinking of adding another lan card and do masquerade also and have the following, public(ether1) ^` private(ehter2) voip(ether...

elkolo23

i have my mikrotik router but i want it to send clients request to a cacheflow i have just acquired instead of using mikrotiks web proxy. for me it would be better since cache flow has 2 drives with its own proccesor so i wont use my router resources for caching. but my probleem is that i need an ex...

elkolo23

i have ran webproxy since this last monday and set available for cache 6gb from system drive,, what i was not sure was for ram cache so i set unlimited,, my router pc is a xeon 2.4ghz with 1024ddr and running on 10gb ide drive... what i noticed was that every day the free memory was reducing until t...

elkolo23

i need to distribute my bandwidth by groups... i have business and home users,,, i need to assure bandwidth to business users with dedicated 256kbps and my home users to share lets say a 512kbps between 5 -10...
could it work with parent quees?

elkolo23

i need to limit a customers by 128kbps during day and 1024 at night.... i tried by time but it happends that at day it works well but at night they willl get more than 1024kbps and also that specific quees wont report how much bandwidth is using... just displays 0kbps

elkolo23

i have a problem several times,,one user keeps changing his ip addres to one i have not assigned... i need a way to end this.(no ppoe) i use static i think there is a way that only hte ips i `pprove will be surfing no matter if he changes ip to a valid one, he will not surf.. also a way to cut the u...

Search found 69 matches