MikroTik

triac

You must create new tool in Tools panel….

triac

Thank's!!!

triac

Hi ppl, someone know the electrical downtilt value of mANTBox 15s & 19s sector antennas?

Tnx

Paolo

triac

Like title... where is winbox in Dude v 6.38??

triac

Same issue! error 10061.. i'll send supout file...

triac

Hi I've been using the new dude installed in a CCR and we see that the "ping" in any of the devices entered the program restarts.

triac

Often when I try to ping some device the Dude client close and restart itself...
Dude Server installed on x86 6.34 rc 21 ROS... (same issue with 6.34 rc 19).

triac

Email - Sends email, need to specify Server address. Authentication not supported.

smtp authentication support add please

triac

...after 72 hours...

how I can recover it?
There is not serial port.....
Ideas about or I must throw it in the trash?

triac

Hi,
Same problem with a lot of RB411R... don't recognize onboard radio, if I try to disconnect and reconnect the power maybe sometime work fine but at next reboot "POOF!!" the radio card disappears...
Tried with 4.5, 4.10, 4.11 and 5.0 beta 6 Fw....

Suggestions?

Tnx
Paolo

triac

Hi Krusty, Your script are very good for me, I have two GW (the first ADSL and the second UMTS) and work fine with Your script... I'm not a genius with scripts, I don't know it but I try to explain You my idea (my english it's orrible...): When the first GW is down and I work with UMTS GW the IP of ...

triac

Hi Demeo, tnx for reply,
I cannot use bridge mode because my ADSL provider ask me PPPoA auth and MT router cannot make this... or I can't know how to made it...

triac

Hi folks, I need help about failover configuration using ADSL as primary link and UMTS router as backup link... I have ADSL router connected to eth1 of my RB450 router and UMTS router connected to eth2... I've tried to make it following this example found in wiki: "/ip route add gateway=192.168...

triac

Hi, I've tried to install dude under ubuntu (using Wine) but it work only as client, server don't work...

Some good soul can help me? I'm a newbie with linux...

Paolo

triac

hi chupaka, tnx for reply. The check GW in PPtP server (the only with two GW) is enabled, when first GW goes down the second start and the PPtP1 connection are killed immediately... on the server, but in the client the PPtP1 link remain up for about 90 secs... when it goes down the second PPtP link ...

triac

Hi, I want know if it's possible to set PPtP Client connection timeout. In other words, I have a CPE with two PPtP configured, the PPtP server have two DSL connections, the first for abitual work and the second for backup. All work fine but when the first DSL goes down the CPE start second PPtP afte...

triac

Hi netwatcher, tnx for reply... Can You let me know where I can find last routerboot version? Now I have 2.19... "for the Rb600 as it had a fix for the DDR about six months ago" hehehe... strange life... I've purchased a RB600 about 1 year ago and work fine without problems... these two bo...

triac

"On 5.8 what is the recommended minimum channel frequency seperation" Depends of channel bandwidth... if this is 20 MHz You need to set a distance of 20 MHz from the channels (ex. 5500-5520-5540-5560) "and on a four sectors AP, Do i need to change polarites between the sectors ?"...

triac

Hi Master... Have You tried with Nstreme? (exact size). I've solved same problem with Nstreme, I have a link for 60 H323 VoIP channels with a bridge on the middle... with 6/7 simultaneous calls the link goes down... with exact size Nstreme enabled and all VoIP channels active I've 1-2msec ping. I ho...

triac

Hi Avix,

I think You need a transparent bridge on your MT....

Plz read this: http://wiki.mikrotik.com/wiki/Transpare ... o_Networks
or: http://wiki.mikrotik.com/wiki/Transpare ... %28EoIP%29

I'm using WDS mode.

I hope this can help You.

Paolo

triac

Hi, I have two RB600 boards just acquired and the problem is auto-reboot every 30-50 secs... (all two boards same problem...). Routerboot: 2.18 RouterOS: 3.10 I've updated routerboot to 2.19 and routerOS to 3.30, now the boards work fine (no auto reboot) but there is a "problem" with eth p...

triac

Hi, I have some RB450 with a problem... the routers reboot itself often and I have this message in log list: "System rebooted because of kernel failure".

What's happen?

UPDATE!!!! Same problem with RB493!!!! It's a RB4XX bug?

triac

Hi, this is my problem... I have two sites with ADSL connection and public IP assigned... I have RB1000 router on site 1 and RB450 router on site 2. I've done a tunnel both two sites using EoIP. In site 1 I have a AS400 server adn in site 2 I have a AS400 Client and some PC connected with AS400 serv...

triac

Hi, this is my problem... I need to connect a central office with remote locations with ADSL/HDSL connections... I've followed instructions of a wiki article (PPTP VPN - multiple ADSL remote locations to Cental Office)... l2tp server work fine, all tunnels work fine and in my clients I have l2tp vir...

triac

Hi, we are a WISP in Italy, http://www.wiplanet.it (Lazio, Viterbo, 100 Km north of Rome). Only Mikrotik and Routerboard products, Pacific Wireless and Waveant antennas.

Paolo

triac

Hi Janisk,

proxy-arp it's enabled, without proxy-arp do not work...

other ideas?

triac

no ideas?

triac

Hi, I hope You can understand, my English is poor... :( I have a PPPoE server MT RouterOS based, this server assign a public IP to every client when it become to the network, all work fine but from a client I cannot reach others client on the same network... example: CPE "A" become to the ...

triac

Hi Edward, Nstreme cannot solve Your problem, I have a 29.5 Km 5GHz-10 MHz WDS link with two 29dBi Waveant dish, two RB411 wiht CM9 card and 5Mt of LMR400 cable (RG213 isn't good to work at 5GHz...). Here my results: WDS link bridge<>station WDS (no AP bridge but it's the same..) SS: -78 dBm CCQ: 70...

triac

HeHe!!! The button gone in vacation? I hope he happy.

triac

..Work!!!

Bah! Why the error at the first attempt?
And in 3.11 there isn't "restore" key in files box... where is it?

triac

ok... wait...

triac

Hi Janisk,

I've re-installed 3.10 from CD (keep config) and router now work... You think the problem came only when I update my router?

I can try to reload 3.11 from CD and restore saved configuration...

triac

Hi, I've tried to update from 3.10x86 (PIII 800 - MB supermicro) to 3.11 but SURPRISE!!

"Loading system with initrd
uncompressing linux... ok. Booting the Kernel
execve 00000002
kernel panic - not syncing - attempted to kill init"

What happens?

Paolo

triac

Hi Lee, tnx for reply... don't work :( I think the problem it's the gateway assigned to the CPE's from the PPPoE... PPPoE server assign a public IP and a GW to a CPE... the public IP are taken from DSL Pools and GW it's the IP assigned to W-LAN card... Example: CPE1 Conf: PPPoE: Connected: Wireless ...

triac

Hi, first of all excuse me for my english, it's very terrible! I hope You can understand me!! I have a problem with MT 3.1 used as PPPoE server... I have 6 DSL connections and 32 public IP's for every DSL... I want assign a public IP for every CPE connected but not statically, I want assign IP's dyn...

triac

Hi McFrosty, Proxy-arp in my PPPoE server work fine! Add IP-pool of your public address range to customer profile xxxxxxxxxxxxxxxxxxxxx example: create pool: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx [xxx@PPPoE Server] ip pool> add name=pool_1 range=88.xxx.xxx.100-88.xxx.xxx.200 [xxx@PPPoE Server] ip pool> [xx...

triac

Hi, I have a strange problem with a 2.4 GHz connection. The CPE connecting and disconnecting often. PLz, look the AP log listed below...... "[tivuesse@AP Bolsena 2 (MTA)] log> print 10:29:54 wireless,info 00:11:7C:0A:39:44@wlan2 - AP Bolsena 2: disconnected, reassociating 10:29:54 wireless,info...

triac

Hi Uldis, I'm sorry for delay, some day ago we have had a small hurricane and my wireless network has been damaged from it. (many antennas destroyed...) MT_Panic.jpg "Kernel Panic - Not Syncing: No init Found. Try passing init= option to kernel" this is the error after upgrade. With 3.02 o...

triac

Hi kujtimhajredini,
today I've tried the same, from 2.9.44 to 3.0rc3 with 6x86 and RB532A, same problem "kernel panic" during restart

.

Uldis, it's impossible to send supout file, the only way to resume the system it's re-install OS via netinstall or re-writing CF.

triac

Same problem for me, after upgrade from 2.9.46 to 3.0rc2 all cpe loosing connection with AP and hotspot stop to work. I've tried to reconnect some cpe (site survey recognize AP but when I try to connect it the surprise "Connect fail"). I've upgraded to 3.0rc3, same problem and 5 GHz link a...

triac

Hi Trottolino,

I don't understand WHERE You have problems, initial router configuration, hotspot activation...

If You have tried a configuration show it us (without IP address!)

Otherwise try to mail me, (maybe in Italian we can understand better...).

Paolo

triac

Hi Trottolino,

What is exactly Your problem?

Hotspot with 4 ADSL MUST work!

Paolo

triac

Hi Craig,

I've found some Zyxel Prestige 662 HD modem, I'll try to apply a fan to it and I hope it work fine!

Tnx for answer

Paolo

triac

Hi trottolino, in English please. Mail me, paolo (at) wiplanet (.) it

triac

Why hotspot?

What You think about PPPoE or PPTP authentication?

triac

Hi Craig, Tnx for answer...

and You know some good modem/router?
I need to install a very stable and affidable product, not commercial "shit".
Can You suggest me some brand or model?

Paolo

triac

Hi, Can anyone tell me if exist some ADSL2+ PCI card compatible with Mikrotik ROS?

If yes which card?

Thank You

Paolo

triac

Yep!! Accept rule work fine!

Thank You Sergejs.

Paolo

triac

Hi, Tnx for answers, nasriza, I've tried with traceroute on both sides but there isn't hops, the PC catches up directly the server and the same for the server, it catches up directly the PC. Letni, for me it's big problem reset the AP but maybe this is the only solution.... The hotspot is also confi...

triac

Hi, this is my problem... I have a bridged network (like image attached) where the PC can ping server, server can ping PC but when I try to have access to server it don't sees PC IP address but 2.4 GHz AP IP address... in other words, PC sees Server with right address (192.168.1.10) but Server sees ...

triac

Hi, two mikrotik have the same ROS version? Have You tried to upgrade ROS?

triac

We need more info about hardware (motherboards, power supply etc.) otherwise nobody can help you.

ciao, devi dirci che apparato usi, quale hardware altrimenti non ti può aiutare nessuno.
Facci sapere.

triac

Hi, after 3.0rc1 upgrade user manager was lost!!

I have tried to download separate packages but there is not user manager package! Any solution?

Tnx

Paolo

triac

...bella questa!!!

Imran, You can download MT directly from MT site, but You need to purchase a key, isn't possible to use the same key for two different installations.

triac

I've disabled routing-test package and enabled routing package, now work fine!!

Bye

Paolo

triac · Re: Gateway problems with ROS 2.9.43 I've tried but doesn't work...

I've tried but doesn't work...

triac

Hi, I've problems with gateway settings with ROS 2.9.43. Please, read below: [tivuesse@AP Coste + Link Guardie] > ip route [tivuesse@AP Coste + Link Guardie] ip route> add gateway=112.135.10.17,112.135.10.18 [tivuesse@AP Coste + Link Guardie] ip route> print Flags: X - disabled, A - active, D - dyna...

triac

Hi, I'm trying to use two RB14 PCI-miniPCI adapters (with 3 X R52 for every adapter) in the same motherboard (Biostar K8M800-M7A with AMD Sempron 3000+ and 256 Mb RAM) but sometime the system crashing without reason.

Anyone have same problem? Can two RB 14 work on the same motherboard?

triac

Uhmmm.... 70/80Mbps radio link? I think You need 4 radio links (NOT single RB532 with 4 radio cards) joined with bonding feature...

This is a question for Janisk... Do You think can be work?

triac

But You have only 1 AP for 50 clients?

Can You explain your network? (Hardware used, processor speed, Internet bandwidth available etc.)

triac

Hi William, are You using winsvr2k3 for dude server and client or only for server?

triac

Yes, the problem it's only with client, the server work fine. I've tried with a PIV 3000 1 Gb RAM, AMD athlon 64 3200+ 1 Gb RAM, a PIII 650 512Mb RAM and notebook Celeron M 512Mb RAM. Always the same problem.
Some idea?

triac

I have the same problem! With "old" 1.2 version I havent problems, with 2.0, 2.1 or beta version I have problems when I try to open "Settings" option. Same problem on 4 different computers. Anyone know the solution?

triac

Hi, I hope You can understand what I want ask... my english it's like a fist on the balls... I have 1 ADSL connection with 16 public IP assigned. Suppose to have this IP: ADSL Router IP: 10.10.10.1 This ADSL is connected to a MT router (public port). Two of 16 IP are configured in Public port (suppo...

triac

Hi, which is the best solution for transparent bridge? WDS Bridge or EoIP tunnel? I mean which is the method that require much resources to the system?

Thank You

Paolo

triac

Hi max, - Galaxynet words: "Your APs should never be on the same channel. And remember there are only 3 non-overlapping channels - 1, 6, and 11". This is the first law. Which is the distance between 2.4 AP antennas? How many CPE for every AP? Which is the distance from AP and all CPE's? (E...

triac

Eh, no.... All firewall are disabled...

triac

Hi, this is my problem... I have two remote Lan's connected with wireless bridge using tree MT routers and double EoIP configuration. http://www.wiplanet.it/images/example1.jpg this is the configuration: MT1: eth 1 IP: 192.168.0.10 wlan1 IP: 10.0.0.1 EoIP tunnel 1: remote IP: 10.0.0.2 - Tunnel ID: 1...

triac

Hi Sergejs,

I have installed wlan card on router and I have success to connect with RB via wlan. Now I have supout file. I'm sending it to You just now. In driver list I've found the Atheros drivers only... and the eth drivers????

triac

Hi Sergejs, I've reproduced same situation and I have the same problem...eth ports dead (leds off). In Interface configuration (via serial console) the eth ports are on running mode. I've tried to disable and enable ports without results. I've generated supout file and now there is another problem.....

triac

Hi! I'veupdated a RB153 with last routerOS (2.9.37). After update and after reboot all eth ports have stopped work. the only alive port is serial port. I have reloaded a 2.9.29 release with netinstall and now work fine ( except frequently auto-reboot ). Anyone have same problem? I've tried to update...

triac

I have the same problem with a RB532, I think it's hardware problem. Others RB532 working fine from about 1 year in critical conditions (4 CM9 cards and very high traffic density) without problems. I have purchased 10 x RB153 just some day ago and I haven't tested it. I think I'll start tests today,...

triac

Hi Sergejs, Thank's for answer

I've tried with two PC connected to the routers but results are about the same....

Any suggestion?

triac

Hi, this is my problem: I have a wireless link (2x RB532 with CM9 cards) and the tx/rx rate is 54 Mbps but when I try to test the link with bandwidth test I have these results: UDP only Receive=6.7 Mbps UDP only Send= 10.9 Mbps TCP only Receive = 5.3 Mbps TCP only send = 6.7 Mbps I have about same v...

triac

Hi Cibernet,

I've found bonding examples on wiki, exactly what I need!

Thank You for help!

Paolo

triac

Hi, It's possible to sum two radio links for increase the bandwidth? I need to transport a 20 Mbit/sec DSL connection to about 20 Km of distance... for obtain a great, stable and redundant wireless link, I've thought to activate two or three radio link and sum it. It's possible? If yes, how I can ma...

triac

YESSSSSSS!!!!

Proxy-arp activated on wan card and all system work fine!!!!

Many Thanks Christian, I've received a great help from You!!!

Paolo

triac

I've tryed to remove masquerading rule and users cannot browse in internet. I think there is some error in address settings.. I don't understand how to configure public address... now I've assigned to the wan card only 1 public IP address and I've created a pool with other address. This pool it's as...

triac

Hi Christian,

Yes, masquerading rule it's active, I need to remove it?

[tivuesse@MikroTik] > ip firewall nat
[tivuesse@MikroTik] ip firewall nat> print
Flags: X - disabled, I - invalid, D - dynamic
0 chain=srcnat action=masquerade
[tivuesse@MikroTik] ip firewall nat>

triac

Hi Christian, Thank You for answer. This is my problem: I have a range of public IP address assigned to my DSL connection and I use a MT (PPPoE server) for user authentication. When some user start connection must obtain public IP address from MT. Now I'm trying your suggestion but I'm sure to mista...

triac

Thank You janisk! Very helpful!!
I think the forum must help non-expert users like me, if I resolve problem with manual I dont ask help on the forum!

Thank You again for help!

triac

Hi, this is my question....
Suppose to have a range of 64 or 128 public IP address available and a wireless network with pppoe authentication, can I assign a public address for every user connected? In other words can routerOS assign public address to user when he start connection?

Thank You

Paolo

triac

Hi, this is my problem... I'm using a MT 2.9.27 router for share ADSL connection with 5 pc (intranet). Someone use my public IP like a SMTP server for spamming action. How I can stop this? I think I need to block traffic on port 25 on public ethernet card, but how I can make this?

Thank You

Paolo

triac

This is the solution for my problem: [tivuesse@Ponte Grotte Castro 1] > ip firewall filter [tivuesse@Ponte Grotte Castro 1] ip firewall filter> print Flags: X - disabled, I - invalid, D - dynamic 0 chain=forward in-interface=ether1 protocol=tcp dst-port=137 action=drop 1 chain=forward in-interface=e...

triac

Hi, I've connected two sites using MT wireless bridge. All two sites have mixed network, IP and Lantastic based. The Lantastic are used for connect Cash machines to the server (cash machines can use ONLY Lantastic) and the servers of the two sites are connected to a central server via IP (using brid...

triac

Hi balimore I have some news.... I've tried to connect UM and MT hotspot via ethernet port, all work fine, same test with PPPoE server, it's OK! But when I try to use a remote hotspot or PPPoE server connected to UM via wireless link (using EoIP tunnel) I have radius timeout error. (in the login pag...

triac

Hi all! This is my problem... I have a MT (x86 based) and I want use it only as User Manager for my wireless network (all my AP's are MT x86 and RB500). When I try to login to my router I have this message on router log: User xxx authentication failed-Radius Timeout (6) This is my test: User Manager...

triac

Hi, this is my problem... I need to limit bandwidth only for 4662 and 4672 (emule) ports, I don't want block the ports, only limit to 128 or 256 Ksec. I'm using 2.9.25 routerOS version. Can Anyone help me? Thank You

Paolo

triac

Hi. I've purchased 5x RB532 Routerboards with routerOS 2.9.20 pre-installed. I'm trying to update to new 2.9.24 routerOS version but when I start ftp the file transfer stop it after some second. I have the problem with all 5 routerboards... what can I do?

Thanks

Search found 90 matches