Community discussions

MikroTik App

Search found 12 matches

by skb73
Thu Jun 25, 2020 1:10 pm
Forum: General
Topic: WIKI "Road Warrior setup with Mode Conf" - not usable for actual version
Replies: 3
Views: 636

Re: WIKI "Road Warrior setup with Mode Conf" - not usable for actual version

You haven't given a link to the particular wiki page you complain about. I believe the information you need is available in this chapter of the official Wiki for IPsec.
my fault. I'm talking about this
https://wiki.mikrotik.com/wiki/Manual:I ... _Mode_Conf
by skb73
Thu Jun 25, 2020 11:00 am
Forum: General
Topic: WIKI "Road Warrior setup with Mode Conf" - not usable for actual version
Replies: 3
Views: 636

WIKI "Road Warrior setup with Mode Conf" - not usable for actual version

Hello! I'm trying to configure "Road Warrior setup with Mode Conf" according to Mikrotik WIKI. But there are some changes made in IPSec since the wiki article was written. I'm stuck on the: /ip ipsec user add name=user1 password=123 add name=user2 password=234 /ip ipsec peer add auth-method=pre-shar...
by skb73
Thu Aug 01, 2019 12:30 pm
Forum: RouterBOARD hardware
Topic: RB4011: wlan1 disabling itself [SOLVED]
Replies: 302
Views: 70468

Re: RB4011: wlan1 disabling itself [SOLVED]

What i forget to write is that i use a CAPs Manager on the hap ac2. I have two hap ac2 running. one of them is the CAPs Manager- Both oft them running without problems. As i wrote before. On my hap ac2 with the caps manager and without local forward on the wifi its running fine. Maybe this helps so...
by skb73
Tue May 14, 2019 10:33 am
Forum: Wireless Networking
Topic: CAPsMAN and CAP AC2 - 5Ghz stops working without any log message
Replies: 23
Views: 4421

Re: CAPsMAN and CAP AC2 - 5Ghz stops working without any log message

I've moved out 4 ACs from CAPsMAN. Flight is normal. Yet.
Have you already reported your findings to MikroTik? (support@mikrotik.com)
I have asked them already about this problem. twice. they are too busy to answer :(
by skb73
Mon May 13, 2019 6:03 pm
Forum: Wireless Networking
Topic: CAPsMAN and CAP AC2 - 5Ghz stops working without any log message
Replies: 23
Views: 4421

Re: CAPsMAN and CAP AC2 - 5Ghz stops working without any log message

My findings on my installation: - Using CAPSMAN with a CAP AC and a HAP AC. The (old) HAP AC works flawless - Using 80 MHz XXXX (40 MHz XX seems ok) - Using automatic freq. selection or a selection of freq. doesn't seem to matter - At least in firmware 6.43 and 6.44 I disabled CAPSMAN a day ago to ...
by skb73
Sat May 11, 2019 1:20 pm
Forum: Wireless Networking
Topic: CAPsMAN and CAP AC2 - 5Ghz stops working without any log message
Replies: 23
Views: 4421

Re: CAPsMAN and CAP AC2 - 5Ghz stops working without any log message

So it´s friday evening and I´m actually looking for information whether RouterOS has problems with high amount of concurrent connected clients. Reported problems by users: Random disconnects, "no internet", "yellow exclamation mark", "cannot ping gateway any longer" ... And now I found this thread?...
by skb73
Wed May 08, 2019 10:41 am
Forum: Wireless Networking
Topic: CAPsMAN and CAP AC2 - 5Ghz stops working without any log message
Replies: 23
Views: 4421

Re: CAPsMAN and CAP AC2 - 5Ghz stops working without any log message

I am seeing the same issue with cAP ac2 and hAP ac2, and have an open support case with Mikrotik for ~10 months. We see SSID beacon frames (among other management frames) aren't transmitted for up to 10 seconds - this evidently occurs due to a compatibility issue with certain 5GHz clients (smartpho...
by skb73
Wed May 08, 2019 9:58 am
Forum: Wireless Networking
Topic: CAPsMAN and CAP AC2 - 5Ghz stops working without any log message
Replies: 23
Views: 4421

Re: CAPsMAN and CAP AC2 - 5Ghz stops working without any log message

I did it. No success. My CAP have lost 5GHz again.

but nothing in log. I attached screenshots. Log file with caps, debug is zero bytes length.
by skb73
Tue May 07, 2019 11:52 am
Forum: Wireless Networking
Topic: CAPsMAN and CAP AC2 - 5Ghz stops working without any log message
Replies: 23
Views: 4421

Re: CAPsMAN and CAP AC2 - 5Ghz stops working without any log message

here are the outputs from CAPsMAN and CAP_IT (which does not working on 5GHz now)
by skb73
Mon May 06, 2019 4:15 pm
Forum: Wireless Networking
Topic: CAPsMAN and CAP AC2 - 5Ghz stops working without any log message
Replies: 23
Views: 4421

Re: CAPsMAN and CAP AC2 - 5Ghz stops working without any log message

Can you please check the "current-state" listed on interface-list printable with "/caps-man interfaces print detail" ? It should show you whether the access point is in state "running-ap" (thats the status you would want) or in some other status like radar-detection and so on.. I have now at least ...
by skb73
Mon May 06, 2019 11:27 am
Forum: Wireless Networking
Topic: CAPsMAN and CAP AC2 - 5Ghz stops working without any log message
Replies: 23
Views: 4421

CAPsMAN and CAP AC2 - 5Ghz stops working without any log message

Hello! SOS!!! I have CAPsMAN on a CCR 1009 and about 20 APs - CAP AC2 all of them are up to date (long term) I have a local forwarding and two VLANs. sometime 5GHz stops working on one or more APs. I can see this situation in WIFI scanners (no signal on my channels and no my SSID is seeng on my lapt...
by skb73
Fri Jan 18, 2019 3:38 pm
Forum: Wireless Networking
Topic: How to bridge dynamic interfaces from CAPsMAN?
Replies: 1
Views: 595

How to bridge dynamic interfaces from CAPsMAN?

Hi! I need to set up some APs with the CAPsMAN. So I need to receive different VLANS attached to different SSIDs with Local Forwarding. I try to set up virtual APs by CAPsMAN. After the CAPsMAN configuration I receive dynamic interfaces on my AP. I bridge them with VLAN insterfaces. And everything i...