Community discussions

Search found 62 matches

by CoolTom
Tue Oct 15, 2019 2:33 pm
Forum: Wireless Networking
Topic: CAPsMAN 5G and 2G network at same time
Replies: 11
Views: 1190

Re: CAPsMAN 5G and 2G network at same time

I would not recommend doing that at all. You force the client to roam when it is not yet ready to, and so make the switchover rather noticeable for the vast majority of clients. And doing so also means the clients leaving your zone of coverage will be out of service sooner. So you leave Signal Rand...
by CoolTom
Sat Oct 12, 2019 1:23 pm
Forum: Wireless Networking
Topic: CAPsMAN 5G and 2G network at same time
Replies: 11
Views: 1190

Re: CAPsMAN 5G and 2G network at same time

Not sure I understand your last question about "signal tuning".
Means what interval set in Access list for device entry, to roam correctly ... min signal like 75 or 85 or 80

od just test it and setup base on real signal?
by CoolTom
Sat Oct 12, 2019 1:13 pm
Forum: Wireless Networking
Topic: SXT LTE lost lte interface
Replies: 34
Views: 7084

Re: SXT LTE lost lte interface

I installed last stable OS v6.45.6 and it seems to be fine now. Now its on for 3 weeks ...

Seems like for "new" Mikrtoik devices (4011, 60G, LTEs) is better use last stable instead of long term ....
by CoolTom
Sun Sep 29, 2019 4:15 pm
Forum: Wireless Networking
Topic: CAPsMAN 5G and 2G network at same time
Replies: 11
Views: 1190

Re: CAPsMAN 5G and 2G network at same time

How you tune signal randge? Do u use -80..120 or test with some device?
by CoolTom
Sun Sep 29, 2019 3:47 pm
Forum: Wireless Networking
Topic: CAPsMAN 5G and 2G network at same time
Replies: 11
Views: 1190

Re: CAPsMAN 5G and 2G network at same time

Same SSID and password, and let the client decide. There will be very limited cases where devices that wont prefer 5G will need 5G. If they are static devices (such as TV's) then you can ACL them onto 5G but ultimately if they are not bandwidth heavy then it won't really matter all that much. ACL -...
by CoolTom
Sun Sep 29, 2019 5:13 am
Forum: Wireless Networking
Topic: CAPsMAN 5G and 2G network at same time
Replies: 11
Views: 1190

Re: CAPsMAN 5G and 2G network at same time

Provided you will most likely build your network using dual-band APs what should happen for one network to go down while another to remain up? 5G has worse wall penetration. So there will be still some "holes" where 2G is but 5G is not. Device still have option connect using 2G. Thats what I mean. ...
by CoolTom
Sat Sep 28, 2019 3:43 pm
Forum: General
Topic: USB UPS connected to RB4011 wifi version
Replies: 6
Views: 577

Re: USB UPS connected to RB4011 wifi version

Or if not use 5G card replace it with this mini PCIe to USB :) but its crazy remove 5G

https://ae01.alicdn.com/kf/HTB1mkJFIXXX ... 0-card.jpg
by CoolTom
Sat Sep 28, 2019 3:41 pm
Forum: General
Topic: USB UPS connected to RB4011 wifi version
Replies: 6
Views: 577

Re: USB UPS connected to RB4011 wifi version

So nit possible just "wire" pin to pin?

https://wiki.mikrotik.com/wiki/Manual:S ... al_Console

somehow to USB-B connector or DB9 connect to USB cable - USB to USB-B

USB to DB9
https://images.monoprice.com/productlar ... /20671.jpg
https://images.monoprice.com/productlar ... /37261.jpg
by CoolTom
Fri Sep 27, 2019 5:26 pm
Forum: Wireless Networking
Topic: CAPsMAN 5G and 2G network at same time
Replies: 11
Views: 1190

CAPsMAN 5G and 2G network at same time

Hi, I am wondering how you guys setup 5 and 2G wifi over CAPsMAN. What works best? As I saw, there are two or three possible options, but both have some negatives: 1. 5G and 2G with same SSID name and some people also r educe 2G transmit power -7dBi below 5G transmit power to force device choose 5G ...
by CoolTom
Fri Sep 27, 2019 2:16 pm
Forum: General
Topic: USB UPS connected to RB4011 wifi version
Replies: 6
Views: 577

Re: USB UPS connected to RB4011 wifi version

Yes, but 4011 not have USB, just RJ45 CONSOLE port and UPS have just USB type B connector. So I was wondering if CONSOLE port is same like serial port and can be used for talking to APC UPS ....
by CoolTom
Fri Sep 27, 2019 12:12 pm
Forum: General
Topic: USB UPS connected to RB4011 wifi version
Replies: 6
Views: 577

USB UPS connected to RB4011 wifi version

Hi, is there any way how to connect APC UPS (USB interface) into RB4011 (RB4011iGS+5HacQ2HnD-IN)?

Like over CONSOLE port?
by CoolTom
Wed Sep 25, 2019 1:15 pm
Forum: General
Topic: MTU and L2 MTU on ether
Replies: 6
Views: 656

Re: MTU and L2 MTU on ether

L2MTU has nothing to do with CPU usage. It is just a limit on the size of the low-level frames. Maybe it has some impact on memory usage (size of buffer used when receiving frames). I never touch it, I just leave it at its value decided by RouterOS. When using link level protocols that add lots of ...
by CoolTom
Sun Sep 22, 2019 6:28 pm
Forum: General
Topic: MTU and L2 MTU on ether
Replies: 6
Views: 656

Re: MTU and L2 MTU on ether

Different hardware has different L2MTU. However it is not important, unless you are doing MPLS and need a lot of L2MTU. For normal use it is only MTU that matters. I see, so i can not expect big change if i change it to same value as other clnnected Mikrotik devices? Its better keep it as it is fro...
by CoolTom
Sun Sep 22, 2019 3:11 pm
Forum: Wireless Networking
Topic: SXT LTE lost lte interface
Replies: 34
Views: 7084

Re: SXT LTE lost lte interface

Happening similar stuff. After few days LTE modem freeze and it just say in status tab: pin status: unknown. LTE interface not disapear. I tryed: USB reset device restart using restart device restart power disconnect AT command /interface lte at-chat lte1 input="AT+reset" change slot A to B and back...
by CoolTom
Sun Sep 22, 2019 2:13 pm
Forum: General
Topic: MTU and L2 MTU on ether
Replies: 6
Views: 656

Re: MTU and L2 MTU on ether

Thank you for your post. I was wondering why different Mikrotik device get "by default" different L2MTU ... IF I connect HeX PoE and RB4011 and each will have on connected ether ports different L2 MTU - 1592 and 1598, will it slow down dataflow - becouse one have to fragment packets? Should I set it...
by CoolTom
Sun Sep 22, 2019 12:23 am
Forum: General
Topic: MTU and L2 MTU on ether
Replies: 6
Views: 656

MTU and L2 MTU on ether

Hi, I am bit confused with MTU and L2MTU value. I am vondering if it should be same on two connected device or better keep it as router set it up? I am having L2 MTU on RB600 - 1600 hAP ac2 - 1598 RB1100Hx4 - 1592 RB4011 - 1592 HeX PoE - 1598 I was reading about packet size but not sure if this valu...
by CoolTom
Mon Sep 02, 2019 8:02 pm
Forum: General
Topic: OSPF setup network with 2 wireless p2p link
Replies: 0
Views: 280

OSPF setup network with 2 wireless p2p link

Hi, can you check if this setup looks good, please? Network with 4+ routers and 2 paralel wireless links. Main LINK A and failover backup LINK B. Routing and p2p failover managed by OSPF + BFD on main LINK A for faster fail detection ... And cost 1 for main LINK A from both sites to force traffric t...
by CoolTom
Mon Sep 02, 2019 11:14 am
Forum: Wireless Networking
Topic: Bondig WIFI links 60G and 5G
Replies: 15
Views: 1551

Re: Bondig WIFI links 60G and 5G

Hi, Why not try to change the priority on the 60Ghz port and also on the 5ghz port with RSTP? 60ghz priority 128 5ghz priority 96 If link break on 60ghz then the traffic will go through the 5ghz, it requires to have two switch between each radio. Thank you, sounds more complicated than OSPF with BF...
by CoolTom
Mon Sep 02, 2019 11:11 am
Forum: Wireless Networking
Topic: Bondig WIFI links 60G and 5G
Replies: 15
Views: 1551

Re: Bondig WIFI links 60G and 5G

Yes to include the management of the WiFi use /29 Well it is of course also possible to use a /24 but what is important is that you should use a separate network for each of the links and not put these things in a bridge as so many people do. So on each router you take out 2 ports from the normal b...
by CoolTom
Mon Sep 02, 2019 10:39 am
Forum: Wireless Networking
Topic: Bondig WIFI links 60G and 5G
Replies: 15
Views: 1551

Re: Bondig WIFI links 60G and 5G

You would recommend to setup 2 /30 networks between the routers and run your favorite routing protocol. Combine it with BFD to make it aware of connection loss a lot quicker than OSPF or BGP do by default. Btw what is advantage of using /30 network instead of /24? Less hosts, lest broadcasts? Not s...
by CoolTom
Sun Sep 01, 2019 9:40 pm
Forum: Wireless Networking
Topic: Bondig WIFI links 60G and 5G
Replies: 15
Views: 1551

Re: Bondig WIFI links 60G and 5G

Do you need transparent behavior? I.e. should it be like a bridge/switch? If not, do not use EoIP but use routing. You can use an autorouting protocol configured for quick switchover (e.g. with BFD). Even when you do require EoIP, you can use a single EoIP pair and use routing to select the path be...
by CoolTom
Sun Sep 01, 2019 5:02 pm
Forum: Wireless Networking
Topic: Bondig WIFI links 60G and 5G
Replies: 15
Views: 1551

Re: Bondig WIFI links 60G and 5G

bounding with active backup will switch over in less than 0.3 seconds if 60GHz link is lost Can OSPF do this job too? like setup ospf interface of both router¨s interfaces connected to p2p link and setup network type as peer to peer? LAN -- eth1 (ospf network type broadcas) ROUTER A eth2 (ospf netw...
by CoolTom
Tue Aug 27, 2019 4:44 pm
Forum: General
Topic: Routing or Bridge for p2p wireless link
Replies: 4
Views: 498

Re: Routing or Bridge for p2p wireless link

Thanks guys, thats what i wanted to hear :)
Btw would u mind give me some idea for routing in whole network?

viewtopic.php?f=2&t=151566
by CoolTom
Tue Aug 27, 2019 3:07 pm
Forum: Beginner Basics
Topic: Routing or Bridging, boning 2 wireless p2ps, RIP
Replies: 1
Views: 327

Re: Routing or Bridging, boning 2 wireless p2ps, RIP

Or make the question more simple. How to setup automatic routing on the whole network and failover on 2 paraller wireless links (main LINKA and backup LINKB). OSPF on whole network (as one backbone area)? OR RIP+ manual rotinng on some routers + EoIP thro wireless and bond them? Or another better so...
by CoolTom
Tue Aug 27, 2019 3:02 pm
Forum: The Dude
Topic: More IP from same router autodiscovery
Replies: 2
Views: 564

Re: More IP from same router autodiscovery

Found it, thank you. I also switch off auto discoverry as it keep adding devices with "netowrk" and "broadcast" IP (x.x.x.0 and x.x.x.255) :(
by CoolTom
Tue Aug 27, 2019 3:00 pm
Forum: General
Topic: Can not see trafic in TORCH
Replies: 2
Views: 382

Re: Can not see trafic in TORCH

Yes its right. So if traffic goes thro one switch chip, than you can not see what connections are there?
by CoolTom
Fri Aug 23, 2019 10:49 pm
Forum: General
Topic: Routing or Bridge for p2p wireless link
Replies: 4
Views: 498

Re: Routing or Bridge for p2p wireless link

Bridge means less package processing on the involved devices ... which means lower delay and possibly higher throughput. However, bridge also means broadcasts (including ARP requests) for the whole subnet will hit all the wireless links (presumably bottlenecks) ... which means somewhat reduced thro...
by CoolTom
Fri Aug 23, 2019 9:36 pm
Forum: General
Topic: Routing or Bridge for p2p wireless link
Replies: 4
Views: 498

Routing or Bridge for p2p wireless link

HI, I am wondering what is "better" (faster/other reason) for wireless p2p link between two lacations. Make it as router to router bridge - one subnet or create subnets between every 2 interfaces on link. Bridge: INTERNET ---- ROUTER A (10.0.0.1) -------- (10.0.0.2) ROUTER_WIRELESS_B ********* wirel...
by CoolTom
Fri Aug 23, 2019 2:04 pm
Forum: Beginner Basics
Topic: Routing or Bridging, boning 2 wireless p2ps, RIP
Replies: 1
Views: 327

Routing or Bridging, boning 2 wireless p2ps, RIP

Hi all. I have question about routing, IP plans and Bonding two wireless p2p. Sorry for the picture, it was more easy hand draw :) Now I have simple setup: Internet - GW Mikrotik ----- 5GHz Mikrotik ***** 5GHz Mikrotik ----- Router Mikrotik --- other LANs (on picture only LINK A). Between every Mikr...
by CoolTom
Fri Aug 23, 2019 1:09 pm
Forum: General
Topic: Can not see trafic in TORCH
Replies: 2
Views: 382

Can not see trafic in TORCH

Hi guys. What am I missing? This is happening on few devices (not one model, not one arch, lates version and also older versions). I see there is traffic on ports but when i run TROCH on each port or bridge where the port is, there is nothing. Traffice between ports 1 and 5. ports are in bridge LAN....
by CoolTom
Tue Aug 20, 2019 11:01 am
Forum: Wireless Networking
Topic: Outdoor sector antennas solution fo AP mANTBox or NetBox
Replies: 4
Views: 749

Re: Outdoor sector antennas solution fo AP mANTBox or NetBox

I prefer NetMetal 2x2, is more flexible. You can add different kinds of antennas. MIMO 2x2 is very popular and you have a diversity of antennas. mANT 120º is too specific design. NetBox is the same, but plastic (I prefer metalic case). NetMetal 3x3 if you not need it, choose 2x2. Regards. Thank you...
by CoolTom
Wed Aug 14, 2019 12:01 pm
Forum: Wireless Networking
Topic: Outdoor sector antennas solution fo AP mANTBox or NetBox
Replies: 4
Views: 749

Outdoor sector antennas solution fo AP mANTBox or NetBox

Hi, I would like to replace my old RB600 with tons of CM9s running on 5G A. Thinking what would be best solution. Can you please give me some ideas? 180° and CPE max 1km. is fine so I am thinking .... 1. 2 x sector antena mANTBox 120° 2. 2 x sector antena mANT + NetBox 5 .. seems like similar RB ins...
by CoolTom
Thu Aug 08, 2019 12:20 pm
Forum: Wireless Networking
Topic: Bondig WIFI links 60G and 5G
Replies: 15
Views: 1551

Re: Bondig WIFI links 60G and 5G

bounding with active backup will switch over in less than 0.3 seconds if 60GHz link is lost Perfect, sounds like best way. Thank you for answers. EoIP for each wireless link. Bonding - mode active backup, slaves both EoIP interfaces, Primary 60G EoIP, Link monitoring - ARP and ARP IP targets IP of ...
by CoolTom
Wed Aug 07, 2019 1:14 pm
Forum: Wireless Networking
Topic: Bondig WIFI links 60G and 5G
Replies: 15
Views: 1551

Re: Bondig WIFI links 60G and 5G

I wouldn't use LACP with links of different characteristics. It can be a nightmare. It's better to configure them in an active/passive fashion with the 5G link acting as a backup and forwarding packets only if the 60G link fails. Thanks for reply. But still bonding EoIP tunnels (and use Active back...
by CoolTom
Tue Aug 06, 2019 11:46 am
Forum: Wireless Networking
Topic: Bondig WIFI links 60G and 5G
Replies: 15
Views: 1551

Re: Bondig WIFI links 60G and 5G

Hoi

What kind of throughput do you get over the links?
5G about 100-190Mb and 60G about 500Mb
by CoolTom
Mon Aug 05, 2019 11:40 am
Forum: Wireless Networking
Topic: 5G N or AC for outdoor AP-Clients?
Replies: 0
Views: 297

5G N or AC for outdoor AP-Clients?

Hi, what is "better" for outdoor use for AP? run it on 5G N or AC (20MHz width)? Or quite same?
by CoolTom
Sun Aug 04, 2019 6:59 pm
Forum: Wireless Networking
Topic: CAPsMAN Access Point Question
Replies: 3
Views: 642

Re: CAPsMAN Access Point Question

CAPsMAN is best way how to control more APs from one place (channels, access list, create more SSID like guest etc). So setup CAPsMAN at first AP A (as is first on way to Internet and its already your network GW). And second / AP B connect to CAPsMAN as CAP. AP A will have: CAPsMAN (channels, access...
by CoolTom
Sun Aug 04, 2019 6:01 pm
Forum: Wireless Networking
Topic: Bondig WIFI links 60G and 5G
Replies: 15
Views: 1551

Bondig WIFI links 60G and 5G

Hi guys, I want create 60GHz link and have 5GHz link backup and fail over. When both on it will bond both link and final speed will be sum of both. If one link will go down, all will go over remining second link. Can this be done with bonding as both links have different speed? Like create EoIP tunn...
by CoolTom
Tue Jul 30, 2019 1:45 pm
Forum: The Dude
Topic: More IP from same router autodiscovery
Replies: 2
Views: 564

More IP from same router autodiscovery

Hosts Autodiscovery keep adding all IPs of one router as new hosts - so same router with 3 interfaces popup on map as 3 routers. How to "link" NIC uder one router/box and not have them as 3 devices?
by CoolTom
Mon Jul 29, 2019 7:15 pm
Forum: The Dude
Topic: Read wireless link stat from Device
Replies: 0
Views: 403

Read wireless link stat from Device

Hi, I am playing with Dude and trying get signal strength, CCQ, TX rate etc. How you guys do it? Best way? I saw two ways: 1. using SNMP (any device with SNMP on), get OID with value, create function with code oid("oid number") and than use this function in data source, label, etc. 2. using Mikrotik...
by CoolTom
Sun Jun 02, 2019 3:08 pm
Forum: Beginner Basics
Topic: Btest, Traffic generator - Testting bandwidth of the link
Replies: 0
Views: 171

Btest, Traffic generator - Testting bandwidth of the link

Hi, long time ago I was always testing bandwith between two Mikrotiks with Btest tool. For example to test bandwidth on p2p link or between Mikrotik in local network and other one in internet. Now (I guess from time of bridge subsystem change), with new FW Btest always load CPU to 100% on both sites...
by CoolTom
Wed May 15, 2019 12:02 pm
Forum: General
Topic: HOWTO: Dual WAN PCC with Dynamic IP
Replies: 32
Views: 4644

Re: HOWTO: Dual WAN PCC with Dynamic IP

Thank you. I do understand, there is different between input or prerouting chain. But this 2 setup solutions looks same and one use input and one prerouting chain to manage connected networks connection. Is it the different in passthrough=no/yes Any differents do it on input or prerouting chain?? Su...
by CoolTom
Wed May 15, 2019 11:57 am
Forum: General
Topic: HOWTO: Dual WAN PCC with Dynamic IP
Replies: 32
Views: 4644

Re: HOWTO: Dual WAN PCC with Dynamic IP

Means I can add routing lookup /ip route rule add action=lookup table=main dst-address=X Or over address lists and we are back with needs to add subnet adress which is changing/dynamic. Or did I miss something in that post? So u suggest add lookup over script instead of "getting subnets" and add the...
by CoolTom
Tue May 14, 2019 1:11 pm
Forum: General
Topic: HOWTO: Dual WAN PCC with Dynamic IP
Replies: 32
Views: 4644

Re: HOWTO: Dual WAN PCC with Dynamic IP

How elase get connected networks subnets (LAN is easy, but LTE intefaces) into Mangle rules and into routes :) :-? This will aways works, no? Even if LTE IP will be privat or public subnet. Cut last part, replace 0 and add /24 mask. If I use only WAN IP, what if other LTE ISP will use different addr...
by CoolTom
Tue May 14, 2019 12:54 pm
Forum: General
Topic: HOWTO: Dual WAN PCC with Dynamic IP
Replies: 32
Views: 4644

Re: HOWTO: Dual WAN PCC with Dynamic IP

Just wondering. In this post example, he use for input trafic marking - chain=input : /ip firewall mangle add action=mark-connection chain=input comment=pcc_rule in-interface=wan0 new-connection-mark=wan0_conn passthrough=no add action=mark-connection chain=input comment=pcc_rule in-interface=wan1 n...
by CoolTom
Tue May 14, 2019 12:21 pm
Forum: General
Topic: HOWTO: Dual WAN PCC with Dynamic IP
Replies: 32
Views: 4644

Re: HOWTO: Dual WAN PCC with Dynamic IP

Thnx, I see. I was trying in winbox and it doesnt allow u save it. CLI works. I guess I will use "network from host IP" conversion. It should always works. /ip firewall address-list set [find comment="WAN1"] address=( (([/ip address get [find interface="lte1"] value-name=network])&255.255.255.0 )."/...
by CoolTom
Mon May 13, 2019 3:27 pm
Forum: General
Topic: HOWTO: Dual WAN PCC with Dynamic IP
Replies: 32
Views: 4644

Re: HOWTO: Dual WAN PCC with Dynamic IP

Yes wrong /32 is one address. So it means that if WAN IP is for example 10.65.123.15/32 and I put into Address list 10.65.123.15/24 or 10.65.123.0/24 it will have same result (match adresses 10.65.123.1-255)? Just need to get connected networks from ISP LTE IPs ... Was like most easy way how to get ...
by CoolTom
Mon May 13, 2019 11:46 am
Forum: General
Topic: HOWTO: Dual WAN PCC with Dynamic IP
Replies: 32
Views: 4644

Re: HOWTO: Dual WAN PCC with Dynamic IP

Was like most easy way how to get 0 on the end of IP to put whole subnet into address list (to manage connected networks). /32 is mask of "ISP privat IP on LTE". If I put whole subnet /24 it will do the same job I guess ... btw how to add string "/32" to the end? Just can not make it work ... /ip fi...
by CoolTom
Sun May 12, 2019 5:02 pm
Forum: General
Topic: HOWTO: Dual WAN PCC with Dynamic IP
Replies: 32
Views: 4644

Re: HOWTO: Dual WAN PCC with Dynamic IP

btw how to add string "/32" to the end? Just can not make it work ... /ip firewall address-list set [find comment="wan0"] address="[([/ip address get [find interface=\"lte1\"] value-name=network]&255.255.255.0)]"."/32"] /ip firewall address-list set [find comment="wan0"] address=([/ip address get [f...
by CoolTom
Sun May 12, 2019 3:14 pm
Forum: General
Topic: HOWTO: Dual WAN PCC with Dynamic IP
Replies: 32
Views: 4644

Re: HOWTO: Dual WAN PCC with Dynamic IP

I described it wrong. I was thinking this means, find address list item with comment "wan0" and "overwrite it" with new IP/subnet - so address list doest grows with adding more end more IPs into address list /ip firewall address-list set [find comment="wan0"] address=$wan0subnet; So u are changing a...
by CoolTom
Sun May 12, 2019 1:30 pm
Forum: General
Topic: HOWTO: Dual WAN PCC with Dynamic IP
Replies: 32
Views: 4644

Re: HOWTO: Dual WAN PCC with Dynamic IP

Hi guys, thnx for reply. I am using Mikrotik LTE card so its second option. You are right it doesnt show in winbox ( network mask) but when u read it in comandline it show /32. I am able get: [admin@LTEstream] > put [/ip address get [find interface="lte1"] value-name=addres] 10.X.X.31/32 [admin@LTEs...
by CoolTom
Tue May 07, 2019 6:46 pm
Forum: General
Topic: HOWTO: Dual WAN PCC with Dynamic IP
Replies: 32
Views: 4644

Re: HOWTO: Dual WAN PCC with Dynamic IP

Thnx for reply guys! I just stuck with LTE setup - 2 LTE modems + 1 cable WAN over eth1. Eth1 works over DHCP Client so no problem. Using Mikrotil LTE modem (s). LTE interface get IP not over DHCP client but Mikrotik automatically add it as dynamic address into /ip addresses. No problem, I get get t...
by CoolTom
Fri May 03, 2019 5:21 pm
Forum: Wireless Networking
Topic: Mikrotik R11e LTE interface no gateway
Replies: 0
Views: 236

Mikrotik R11e LTE interface no gateway

When this modem connect fo LTE it automaticalli create dynamic IP in address list, add DNS and add routes. BUT is doest show LTE gateway IP. Where to get gateway IP for script updating Address list to be able work with dynamical IP in PCC load balancing?
by CoolTom
Fri May 03, 2019 5:01 pm
Forum: General
Topic: HOWTO: Dual WAN PCC with Dynamic IP
Replies: 32
Views: 4644

Re: HOWTO: Dual WAN PCC with Dynamic IP

Just wondering: Whi didnt you put the dhcp script into /ip dhcp-client -- Lease script and it will run always (only) when DHCP client obtains new lease or loses existing. No need to schedule it and have delay in address updates .... ?
by CoolTom
Wed Apr 17, 2019 10:04 am
Forum: Wireless Networking
Topic: RBM33G + 2 x R11e-LTE Modems video streaming
Replies: 0
Views: 269

RBM33G + 2 x R11e-LTE Modems video streaming

Hi, I would like to use RBM33G and two R11e-LTE modems to create box for video streaming. It should work like: If eth1 (WAN with DHCP) connected send to internet over eth1 else over LTE1 (WAN) if LTE1 drop than LTE2 (WAN) Also will be handy agregate LTE1 and LTE2 if both connected. So basically fail...
by CoolTom
Mon Apr 15, 2019 7:29 pm
Forum: RouterBOARD hardware
Topic: Case for RBM33G with Dual LTE
Replies: 3
Views: 1021

Re: Case for RBM33G with Dual LTE

Do you have 3d printer? https://www.thingiverse.com/thing:3561672
3D model of box for RBM33G. Thanks to mrkrash.
by CoolTom
Fri Apr 12, 2019 1:16 am
Forum: Wireless Networking
Topic: LTE modem R11e-LTE antena connect
Replies: 5
Views: 592

Re: LTE modem R11e-LTE antena connect

Oh very nice answer. Thank you a lot!
by CoolTom
Thu Apr 11, 2019 3:21 pm
Forum: Wireless Networking
Topic: LTE modem R11e-LTE antena connect
Replies: 5
Views: 592

Re: LTE modem R11e-LTE antena connect

Do you mean Left (with label AUX) or Right (with label MAIN)? What means "diversity". Is it different from Chains on wifi card? More antenas connected = more ways = faster?

Thanks a lot
by CoolTom
Wed Apr 10, 2019 4:54 pm
Forum: Wireless Networking
Topic: LTE modem R11e-LTE antena connect
Replies: 5
Views: 592

LTE modem R11e-LTE antena connect

Just wondering about connecting antena. LTE modem R11e-LTE has two connectors. Do I need connect both of them with antena? Two antenas per card? Or just one and AUX leave not connected? Thnx
by CoolTom
Mon Feb 25, 2019 5:31 pm
Forum: General
Topic: Feature Request: CAPsMAN Clients SNR/Quality
Replies: 1
Views: 1676

Re: Feature Request: CAPsMAN Clients SNR/Quality

Any changes about this? How you tune wireless setup without seeing SNR and CCQ in CAPsMAN??
by CoolTom
Fri Feb 08, 2019 12:31 pm
Forum: Wireless Networking
Topic: Mikrotik and Huawei 3372 LTE modem - LTE Passtrough
Replies: 7
Views: 6377

Re: Mikrotik and Huawei 3372 LTE modem - LTE Passtrough

Any success with this? What I find out after bit researching: 2basic modes working actially with Mikrotik: 1. Stick mode - firmware start with 21.xxxxxx - it appear on USB port and as PPP interface. You are able diap up and if mobile providrer give you public IP you got this public IP on PPP interfa...