Community discussions

Search found 11 matches

by davros
Wed Jul 17, 2019 7:25 am
Forum: Forwarding Protocols
Topic: How to correctly work an OSPF multi area network?
Replies: 3
Views: 476

Re: How to correctly work an OSPF multi area network?

Hello everyone, thanks for your answers, I told you that I just finished configuring in gns3 the configuration that I have in the network, it is a wisp network and I wanted to see the most optimal, that's why it was the question, now I have it configured as I attached them in this new image, the thi...
by davros
Thu Jul 11, 2019 7:12 pm
Forum: Forwarding Protocols
Topic: How to correctly work an OSPF multi area network?
Replies: 3
Views: 476

How to correctly work an OSPF multi area network?

Dear, for consulting something specific, I am currently passing the network with OSPF, but I have a question. Is it advisable to make a network without the Backbone 0 area? Could a multi-area network be made without the Backbone 0? the issue is that I configured with the backbone but when wanting to...
by davros
Mon Jun 10, 2019 4:45 am
Forum: Forwarding Protocols
Topic: How to assign routed public ip
Replies: 2
Views: 459

Re: How to assign routed public ip

Ok, I do not understand the procedure very well, is there any way to do it from "/routing filter" to continue with the same dynamic routing procedure? As I indicated in my first post what I want is to get the public IP (190.94.xx.xx.xx / 30) behind a private ip (172.168.2.6/32), it should be noted t...
by davros
Thu May 02, 2019 1:27 am
Forum: Forwarding Protocols
Topic: How to assign routed public ip
Replies: 2
Views: 459

How to assign routed public ip

Greetings to all, I currently have a network with ospf interconnected several nodes, my clients are with private ip with pppoe in the range 172.168.0.0/22, now I am presented with the need to assign one of my clients a public ip that requires for your business because it says that you will use for m...
by davros
Fri Apr 26, 2019 5:59 pm
Forum: Forwarding Protocols
Topic: MPLS does not mark anything in the table
Replies: 3
Views: 352

Re: MPLS does not mark anything in the table

I solved, now if you mark me the tables normally, human error
by davros
Fri Apr 26, 2019 5:30 pm
Forum: Forwarding Protocols
Topic: MPLS does not mark anything in the table
Replies: 3
Views: 352

Re: MPLS does not mark anything in the table

Attached capture of what is in mpls, until what is mpls is not more science but the truth is because I do not mark anything, in the capture can be seen, even in the tab "LDP Neighbor" you can see two neighbors but the strange thing is that it disappears every moment, I have a point-to-point link wit...
by davros
Thu Apr 25, 2019 3:37 pm
Forum: Forwarding Protocols
Topic: How to implement Balancing PCC with OSPF network
Replies: 5
Views: 407

Re: How to implement Balancing PCC with OSPF network

So what could I do to configure the load balancing pcc with ospf according to the design shown, which is the network that we have at the moment? or do I have to configure BGP on the network to be able to implement it? taking into account that the router only performs NAT work
by davros
Thu Apr 25, 2019 6:55 am
Forum: Forwarding Protocols
Topic: How to implement Balancing PCC with OSPF network
Replies: 5
Views: 407

Re: How to implement Balancing PCC with OSPF network

I attach a better image so that it is understood
by davros
Thu Apr 25, 2019 5:30 am
Forum: Forwarding Protocols
Topic: How to implement Balancing PCC with OSPF network
Replies: 5
Views: 407

Re: How to implement Balancing PCC with OSPF network

Thank you very much for the response, I commented the following: 1. Do you establish any BGP peer between your providers and you?? or I told him that I do not have BGP applied between the providers and my network. 2. Do your providers assign you public IP addresses and your router is the one who do ...
by davros
Thu Apr 25, 2019 2:16 am
Forum: Forwarding Protocols
Topic: How to implement Balancing PCC with OSPF network
Replies: 5
Views: 407

How to implement Balancing PCC with OSPF network

Dear, at present I have my network with OSPF and I see myself in the need to configure balancing in my network to get my traffic through two different ISPs, the query is going to how can I do this? or simply the configuration is typical of the swing, if it were different they could indicate me some ...
by davros
Thu Apr 25, 2019 2:02 am
Forum: Forwarding Protocols
Topic: MPLS does not mark anything in the table
Replies: 3
Views: 352

MPLS does not mark anything in the table

Regards, The reason is to consult the following, I have a network of several nodes which I am migrating to OSPF + MPLS + PPPoE + Vlan (per node), at the moment the network is in bridge mode and in each AP I have assigned VLan + dhcp from the edge router that is in my office, the point-to-point links...