Hi I do have issues with the CRS305-1G-4S+IN , used as a hub, very simple, no vlan stuff no nothing but got lot of disconnect error. The setup is : Esxi box in 10g to the CRS305 and then a dac cable to the rb4011. On the esxi6.7 box i got about every 10sec error message : Physical NIC vmnic1 is down...

Hi So while i did get the nice unit CRS305-1g-4s like 3yrs ago, i finally plug it in, but description being so bad.. that was the reason i did not used it before. Basically this is a super nice 10g HUB. You plug dc power and 1 dac cable to your router and hop you have full 10g network on other port....

Indeed, that can be usefull to know. As if we turn off the router function and used it as nic card, will it give like a 24gb total ? Or like speed reduce to 12gb on each port ?

Indeed, some more quick set tick box could be quite handy for a starting configuration. It take many about a week to find out how to configure , for basically, just get a robust firewall and get the voip service passing. So yes, a kind of wizard could be very usefull for large majority of user. If p...

Just to follow up, i had enable the : service port : pptp in the firewall / service port tab. and as soon i click all connect fine. Strange that i had to open it. Perhaps the new firmware block some incoming port by default. I've try before to just put a new rules: tcp accept port 1721 for the pptp....

Hi So i did update the firmware to the new rev.6.46.1 and since then, i got problem to connect to vpn from the Synology Nas. Only from the nas and nothing else was change. I do have a port open in the filter rule as : accept/input tcp 1194, same as since 6month and working fine. This port i used fro...

When i did mine, it's really, 1 pc, no internet, no router. Just pc plug to the mk router. Then boot with the long press of the button with the corresponding flashing light. or no flash..
then the device will appear in the device list.

160mg is for future, if people try or complain about an iphone not connecting at that speed.. the istuff don't support it. The ac norm is not made to be all time on, it's an hashing power. Better to used the 10g fiber port or simple eth cable to have a full conectivity. Why wifi is so needed ? Only ...

I got the same issues and my Hik cam was working when i set a port foward. Now the firewall rules are quite too hard and that don't work anymore, but i just connect via vpn and uber safer than having a openport.

have you tried it fresh, no ipv6, no tunnel, no extra firewall ?

Hot.. quite interesting. No one told about real data, just 1 post and don't know with what device it was took. My ex cry about everything is cold and me i was cooking. My rb in system health is at 40dC, room temp at 28.5 quite hot. And with a termocouple K type, a 1/8 of it, i can get a case temp of...

Have you try to first install fresh with netinstall 6.44.3, and then only used the: quick set and just put a password and a name ? No vpn, no port blocking.. no nothing. I'm on 20-40-80ceee , freq/chan : auto, no country set. ap-bridge and i get full speed and no disconnect at all. ssid always prese...

I had many strange problem lately with the unit, but the wifi was the perfect result and working fine all the time. 2.4g and 5g have 2 different ssid name. txpower manual. no country set. 20/40/80Mhz Ceee, detect fine 5g 433mbps. Putting 160mhz is for very new device, there's not much that work with...

Indeed, it look to have cut many request. Thanks for that. By default, it was just from the factory reset rule. with 3 additionnal. So as you said : if i put : add action=accept chain=input dst-port=1194 protocol=tcp comment="OpenVPN" This mean it's for the mikrotik router running a vpn se...

With the wiki.. on the : address-list=ssh_blacklist : do we need to create somewhere the ssh_blacklist ? or it will be creating a log or something like that.. ? And do we just add those action in the firewall filter just before the : : add action=drop chain=forward comment="defconf: drop invali...

I did find this to force access to router, only from pc within this specific lan. : add action=drop chain=forward in-interface=bridge1 src-address=!192.168.0.0/24 comment="Drop all that do not match LAN IP" So with this, can it then make the service port ssh and other less problematic and ...

Hi During a full flash of the router and finally getting some better result.. i found out in the winbox terminal lot and lot of Internet hacker or bot trying to access to the router. 17:37:33 echo: system,error,critical login failure for user user from 165.22.122.201 via ssh [admin@RouterOS] /ip fir...

I try many aspect, i try to only go with the nat, than add firewall filter after, remove the drop rules.. I've read and think i understand the wiki too as : https://wiki.mikrotik.com/wiki/Manual:IP/Firewall/NAT . But so far i can only have 1 port foward that work to an internal web login page. But i...

So i've spend the day on this again and so far i see it work for about 2 min, then drop... Like i remove all nat Same for the ipphone.. if plug on an old router it work, unplug old router and put on the rb4011, now ipphone do work and after like 10-20min it stop. And the vpn don't work. For the vpn ...

Well, indeed it look to be the case. I wasn't sure to get it right. But at same time not much port look to work, but it should be quite standard as per all i find. Here's what i got currently : /ip firewall filter add action=accept chain=input comment="Top:" connection-state=established,re...

From this older post.. This is one of the bug i have. Like an android phone with a vpn provider work fine everywhere, but when connect in the mikrotik... vpn traffic is blocked. so is it just adding this ? add action=dst-nat chain=dstnat comment="softvpn pass" dst-port=1196 protocol=tcp to...

I was able to load an old config and winbox came back up. Pretty sure fastrack do something bad.. Here the rules present now that i cannot figure out : Firewall filter flags: X - disabled, I - invalid, D - dynamic 0 chain=input action=accept connection-state=established,related 1 X ;;; S1: accept in...

So i've check further and put on a quite basic rule.. i guess .. But i do don't get why i can't have access to a softvpn. Softvnp.. any software you put on a pc.. And the weird thing is with this, at one point the voip phone start to work.. I clic l disable the filter rule to confirm it was the good...

Hi here is 2 rule that i've found. I got problem with order, but these might work. 21 ;;; Plex Ports - TCP chain=forward protocol=tcp dst-port=3005,8324,32469 22 ;;; Plex Ports - TCP chain=forward protocol=udp dst-port=1900,5353,32412-32414 Can you post your / firewall filter and firewall nat / fire...

Hi So i swap the router with a new RB4011, but as all the research made, i still struggle to get special service running. I do have all rules in place, but might be in wrong order... or the input/ output interface required or not... Basically, i have the port 25 blocked, a softVpn don't connect(1196...