Community discussions

Search found 30 matches

by jfrater
Sat Nov 14, 2015 3:37 am
Forum: Wireless Networking
Topic: BIG BUG- Unicast key exchange timeout
Replies: 120
Views: 93055

Re: BIG BUG- Unicast key exchange timeout

This happened to me today with an antenna running 6.31. Since 6.31 has the password bug (where it literally changes passwords to asterisks) I had to change my password on the AP to "**********" let the client connect, do the upgrade to 6.33 and only then change the passwords back. Just in case this ...
by jfrater
Mon Jun 23, 2014 2:58 am
Forum: General
Topic: Mikrotik PoE + Gigabit never better than 100Mbit/s fdx.
Replies: 12
Views: 4328

Re: Mikrotik PoE + Gigabit never better than 100Mbit/s fdx.

Check your cables and inyectors. I use Cat 5e and I get 1Gbps no problem both with mikrotiks fancy PoE or the low cost (black no LED) On a 711G [jfrater@AP C Azul 1] /interface ethernet> monitor 0 name: ether1 status: link-ok auto-negotiation: done rate: 1Gbps full-duplex: yes tx-flow-control: no rx...
by jfrater
Mon Jun 23, 2014 1:52 am
Forum: General
Topic: ipv6 route list destination filter
Replies: 0
Views: 589

ipv6 route list destination filter

Hi!

Any idea why on the ipv6 route list there is no option to filter a network like /32 or /30?

Image

Basically every way to filter BUT dst. address.
by jfrater
Fri Jun 13, 2014 9:41 pm
Forum: RouterBOARD hardware
Topic: SFP module on SFP+ port on CCR1009 does not work
Replies: 2
Views: 3067

Re: SFP module on SFP+ port on CCR1009 does not work

OK, to answer my own question yes it works BUT you have to disable auto-negotiation on BOTH sides. I assumed it was only on the SFP+ side, but no, on the RB2011 wich has a SFP port, I had to do it also: [jfrater@CRIX] /interface ethernet> moni 8 name: sfp-sfpplus1 status: link-ok auto-negotiation: d...
by jfrater
Fri Jun 13, 2014 6:10 pm
Forum: RouterBOARD hardware
Topic: SFP module on SFP+ port on CCR1009 does not work
Replies: 2
Views: 3067

SFP module on SFP+ port on CCR1009 does not work

Hi, I'm trying to install 2 MAXXWAVE SFP modules on the CCR1009-8G-1S-1S+ but only the SFP port works On the SFP+ port the module shows up, but it does not transmit so the other side shows no-link [jfrater@CRIX] /interface ethernet> monitor 8 name: sfp-sfpplus1 status: link-ok auto-negotiation: done...
by jfrater
Tue Jun 10, 2014 8:41 pm
Forum: General
Topic: v6.14 released
Replies: 115
Views: 24593

Re: v6.14 released

Upgrading from 5.x to 6.14 will remove wireless config so DON'T! :shock:

If you want you can upgrade to 6.13 AND THEN to 6.14, that works fine. 8)
by jfrater
Wed Jul 03, 2013 6:53 pm
Forum: General
Topic: ROS 6.x Simple Queue Time Match Problem.
Replies: 4
Views: 2612

Re: ROS 6.x Simple Queue Time Match Problem.

Yes, sorry for that, it´s a feature not a bug. Now, in ROS 6.x, rules will show up as invalid if they are outside the time range. It makes sense since before you couldn't tell if a rule was "active" or not. :D
by jfrater
Mon Jul 01, 2013 5:52 am
Forum: General
Topic: ROS 6.x Simple Queue Time Match Problem.
Replies: 4
Views: 2612

Re: ROS 6.x Simple Queue Time Match Problem.

In my case the time set as the end time becomes invalid IF it is less than the actual time... so if the routers clock says it 8:46 pm you can't have a rule set to 8:45 but it's OK if it's 8:47. BUT it will becoame invalid 2 minutes later, nice bug ehh? :D
by jfrater
Mon May 23, 2011 1:36 am
Forum: General
Topic: Listing the routing table via SNMP
Replies: 17
Views: 9531

Re: Listing the routing table via SNMP

Well to answer my own question, if I force the SNMP program to use SNMP v1 it works, it does detect the router to be v2 compatible and thats why I only tried v2, but at least on RouterOS 4.9 it works with v1

Jorge
by jfrater
Wed May 18, 2011 8:59 am
Forum: General
Topic: Multiple EoIP tunnels how to?
Replies: 4
Views: 1409

Re: Multiple EoIP tunnels how to?

each tunnel should have it's own id, then add them as a port on your single big bridge.

Jorge
by jfrater
Wed May 18, 2011 8:51 am
Forum: General
Topic: Listing the routing table via SNMP
Replies: 17
Views: 9531

Listing the routing table via SNMP

Hi, I want to get the routing table from a router but with no luck, everything else like IP and interfaces have no problem.

Is there a way to do that on routerOS? I've tried v 4.9 5.0 and 5.2 and nothing.... :(


Thanks

Jorge Frater
by jfrater
Fri Mar 04, 2011 11:12 pm
Forum: General
Topic: IPv6 to IPv4 translation?
Replies: 4
Views: 808

IPv6 to IPv4 translation?

Hello there! I´ve my own IPv4 /21 net and a IPv6 /32 net working nicely. The thing is that one of the servers is running cPanel and the don´t support IPv6 just yet. I've looked at a couple of ways to reverse proxy or translate a site on an IPv4 server to be able to talk to the IPv6 world. Is that so...
by jfrater
Fri Aug 27, 2010 6:07 am
Forum: General
Topic: MIB problem introduced on ver 4.11
Replies: 0
Views: 327

MIB problem introduced on ver 4.11

Hi, I use the voltage meter quite a lot since all my APs are connected directly to a 12 V battery. So in ver 4.9 I get: [root@ns objects]# /usr/bin/snmpget -t 1 -r 9 -m ALL -v 1 -c public 172.22.4.10:161 1.3.6.1.4.1.14988.1.1.3.8.0 SNMPv2-SMI::enterprises.14988.1.1.3.8.0 = INTEGER: 126 So I know eve...
by jfrater
Wed Dec 30, 2009 6:34 am
Forum: General
Topic: RB 112 Running 4.3 Unable to Reboot
Replies: 4
Views: 1042

Re: RB 112 Running 4.3 Unable to Reboot

BTW, what I meant to say with the attached print screen is:

They have very little memory, so be sure to disable all unnesesary packages, also, be sure to upgrade your firmware, sys rou up should do it.

Bye and good luck,

Jorge
by jfrater
Wed Dec 30, 2009 6:22 am
Forum: General
Topic: RB 112 Running 4.3 Unable to Reboot
Replies: 4
Views: 1042

Re: RB 112 Running 4.3 Unable to Reboot

Well, call me crazy, but I did install 4.4 on a RB112 just to see what happens, and it's running just fine!
by jfrater
Mon Apr 28, 2008 3:52 am
Forum: General
Topic: Very low performance using Mikrotik for routing (with Queue)
Replies: 3
Views: 1142

Re: Very low performance using Mikrotik for routing (with Queue)

Did you fix this yet?

BTW have you tried just making one simple queue at one interface? (intead of 2 rules)

Like queue>general>max TX>6M and max RX>6M then on advanced interface> xxxx

It's what I use and it works fine....

Jorge
by jfrater
Mon Apr 28, 2008 2:29 am
Forum: General
Topic: Atheros AR9160
Replies: 4
Views: 3412

Re: Atheros AR9160

ok, any idea when they will? or if they will at all?

Or any other option on upgrading backbone speed?
by jfrater
Sun Apr 20, 2008 7:11 am
Forum: General
Topic: Atheros AR9160
Replies: 4
Views: 3412

Atheros AR9160

Is the current version of ROS 3.7 ready to handle Atheros AR9160 chipset mini PCI cards?

Thanks,

Jorge
by jfrater
Sat Nov 24, 2007 5:28 am
Forum: General
Topic: VPN problem
Replies: 1
Views: 967

VPN problem

Hi there:

Using RC 10 on an Intel P4, 5 eth interfaces, I set up ppp and it works great, for a while. Then it suddenly stops working and after a reboot of the server it works fine again.

Any ideas on what could be hapening? :shock:

Thanks

Jorge
by jfrater
Sun Nov 11, 2007 7:10 pm
Forum: Wireless Networking
Topic: Jumper settings for 24v on RB532
Replies: 1
Views: 739

Jumper settings for 24v on RB532

Hi:

Could anyone tell me what jumper settings they are using when conecting the RB532 to a 24v power supply?

In my case we use 2 12v batteries to power them, before we where using 3 6v, and on one of the sites a 532 got fried after changing from 18 to 24...

Thanks

Jorge
by jfrater
Sun Nov 11, 2007 2:51 am
Forum: General
Topic: Packet loss
Replies: 4
Views: 1143

Re: Packet loss

BTW. Only the very basic is enabled: advanced-tools, dhcp, routerboard,security, system and wireless. on the CPU issue, I did check the CPU, with v3 it was between 2 and 6%, but every 5 or 10 secs it jumped to 100% then back to between 2 and 6% After the downgrade, cpu load stays at 0 to 4%. Jorge.
by jfrater
Sun Nov 11, 2007 1:43 am
Forum: General
Topic: Packet loss
Replies: 4
Views: 1143

Re: Packet loss

That's simple, because I bougth 6 RB 333 to be used as AP, but they give me so many problems that I rather use the 112. I'm 99% sure that it's a software/config problem, because I can only use ver 3 x on the 333s. Using 2.9 gives me no problems on any hardware, this is the reason I'm writing in this...
by jfrater
Fri Nov 09, 2007 12:20 am
Forum: RouterBOARD hardware
Topic: ver 2.9.xx for board 333
Replies: 2
Views: 929

ver 2.9.xx for board 333

hi there...

Could somebody tell me why there is no ver 2.9.xx for the board 333?

thanks

Jorge
by jfrater
Fri Nov 09, 2007 12:05 am
Forum: General
Topic: Packet loss
Replies: 4
Views: 1143

Packet loss

OK, I don't know what the problem is, so I'll just explain what I did. AP is running ver 2.9.48 on 112 board, Ubiquiti SR5 radio. Client is running ver 3 RC9, on board 133c, R52 radio. 5Ghz band, 5180 MHz It *feels* slow, if you do a ping you see many time outs. :( So, we downgrade the client to 2.9...
by jfrater
Wed Oct 24, 2007 5:30 am
Forum: General
Topic: Duplicate pings after routerboard 333 upgrade
Replies: 5
Views: 1429

Re: Duplicate pings after routerboard 333 upgrade

Well, ever since I upgraded to 3 RC 6 the clients don't drop, so something was fixed I guess.
by jfrater
Fri Oct 19, 2007 8:07 am
Forum: General
Topic: Winbox crashes when cliking clock.
Replies: 1
Views: 958

Winbox crashes when cliking clock.

Hi all,

I just upgraded my 333 AP board from RC4 to RC6 and now when I go on the winbox (2.2.11) system -> clock it just closes the winbox window.

Any Ideas?

Jorge
by jfrater
Fri Oct 19, 2007 7:57 am
Forum: General
Topic: Duplicate pings after routerboard 333 upgrade
Replies: 5
Views: 1429

Re: Duplicate pings after routerboard 333 upgrade

Ok, now it's even worse, now it's dropping clients, you can see them registered but you cannot ping them from the AP.

Is this a software or hardware malfunction? Should I just go back to using the 112 with 2.9.46?

Thanks

Jorge
by jfrater
Fri Oct 19, 2007 12:38 am
Forum: General
Topic: Duplicate pings after routerboard 333 upgrade
Replies: 5
Views: 1429

Re: Duplicate pings after routerboard 333 upgrade

By the way, could this be related to heat issues? It's just that I noticed that the problems are worse during hottest hours.
by jfrater
Thu Oct 18, 2007 6:35 pm
Forum: General
Topic: Duplicate pings after routerboard 333 upgrade
Replies: 5
Views: 1429

Re: Duplicate pings after routerboard 333 upgrade

They’re no bridges on the network. We do have redundant paths using OSPF, but that's on the backbone, from it, via Ethernet we connect this AP, it does not have OSPF, it only uses 2 interfaces, the Ethernet to connect to the backbone and one Ubiquiti XR5 on a /27 IP net to connect to all the 14 clie...
by jfrater
Thu Oct 18, 2007 7:19 am
Forum: General
Topic: Duplicate pings after routerboard 333 upgrade
Replies: 5
Views: 1429

Duplicate pings after routerboard 333 upgrade

Hi,

2 days ago I upgraded an AP wich had an 112 to a 333, since then I've been getting duplicate pings on the clients that have lower signals, arround -85 Db

I'm running v3 rc4, but tried v3 rc6 with same results. Also, all of the 14 clients on that AP run 2.9.46

Any ideas?