I have a Mikrotik Router with 16mb of internal storage. Normally, I have 1mb of free space. But lately, I have been noticing that it gets full so I delete some saved backups to free some space. Now I have nothing to delete but the internal storage is still full. I normally do a factory reset and loa...
(2) Why is your IP address for wg99 10.200.200.2/24 - was it given to you by a third party provider?? (3) These rules are TOO WIDE OPEN add action=accept chain=forward in-interface=wg99 add action=accept chain=forward out-interface=wg99 I have followed the instructions from the very first post on t...
I think I followed the recommended settings based on the other post in the forum but it still doesn't work. Whenever I enable the routing rule, the device wouldn't connect to the internet. My goal is to be able to use the wireguard as gateway so that the public of the device with an IP address of 19...
If ever the local IP address 192.168.88.5 is a computer, will that computer be able to use the public IP address of the VPS as its own public IP address?
I am still trying my best to accomplish my goal using the method you recommended which is to use a CHR. I have a question about the original post of "erkexzcx". Let's say his method works, that means that I am not limited to 1MBPS of speed only, is that correct?
Hi Hominidae, I was able to setup a Mikrotik CHR. It has just the default configuration. My understanding is this: Mkrotik CHR (public IP) <------wireguard tunnel------> my local Mikrotik (CGNAT) In configuring the wireguard of the local Mikrotik, I put the public IP of the Mikrotik CHR is the endpo...
Thanks Hominidae! I was able to add the wg interface to the LAN list (and WAN list). Both or either of them works and I don't know the difference but as of now, it is just in the LAN list. The VPS shows that a peer is connected. The peer is my Mikrotik Router. I can now ping the 10.200.200.2 from VP...
TL;DR Get a cloud VM with public IP, host wireguard server on it, connect to it from Mikrotik router, port forward everything from VM to Mikrotik via wireguard tunnel. Other notes: Linode provider offers cheapest instance for 5$/month and you get 4TB of monthly TX data. RX data is not counted (free...
TL;DR Get a cloud VM with public IP, host wireguard server on it, connect to it from Mikrotik router, port forward everything from VM to Mikrotik via wireguard tunnel. Other notes: Linode provider offers cheapest instance for 5$/month and you get 4TB of monthly TX data. RX data is not counted (free...
Thank you. This is helpful. I just don't know how to do the last part. Once done, you should have connectivity from Linode's instance public IP address. Try port forwarding port in your Mikrotik router and checking port on your Linode's instance IP - it should return what your router is supposed to ...
I am using mobile data for internet connection and it is behind a CGNAT. I don't have my own public IP address. I found an article online which gives a guide on how to port forward a certain port from a Virtual Server in the Cloud to a local network. The Virtual server has its own public IP address ...
Hi Anav, It has been a while and there were many changes I have done to my router. I have set up the Mikrotik again just to make it clean when I post it here. Here is the current setup: bridge1 = eth3, eth5, wlan1 and wlan2 bridge2-hs = eth4, wlan3 and wlan4 My goal is to utilize VLAN. VLAN1 for bri...
Hi, As of now, the Mikrotik is not configured to use any vlans (aside from vlan1 if that is the default). How do I configure the Mikrotik so that Bridge-HS will use vlan28? The goal is to make ng port 4 and 5 of the Mikrotik to be part vlan28. The AP that connected to port 5 of Mikrotik is not vlan ...
HI, The script below creates the file but it is empty. I would like the results to be saved on the file aside from just showing on the terminal. Is that possible? :foreach i in=[ /ip/hotspot/user print file=aaaaaaaaaaa detail as-value where comment=admin ] do={:put (("username: " . $i->&qu...
I would like the results to be saved on the file also aside from just showing on the terminal. :foreach i in=[ /ip/hotspot/user print file=aaaaaaaaaaa detail as-value where comment=admin ] do={:put (("username: " . $i->"name") ." " . "password: " . ($i->"...
How can I make the results save to a file? My command prints the results on the terminal and creates the file but the file is empty. :foreach i in=[ /ip/hotspot/user print file=aaaaaaaaaaa detail as-value where comment=admin ] do={:put (($i->"name") . " " . ($i->"password&qu...
Is this because the traffic from the Hotspot users going to 10.5.50.2 does not reach the Mikrotik router anymore as it happens locally to the TPLink router?
I have a TPLink router that is configured to work as AP mode. It is connected to one of the Ethernet ports of a Mikrotik router. That port is configured to use the Hotspot Bridge. The TPLink router got an IP address of 10.5.50.2 and its web interface is accessible from any of the Hotspot users. I wo...
Sorry, it has been a while since I tried it and forgot which one was not working. All I want is this mangle rule: chain=prerouting action=mark-routing new-routing-mark=giga passthrough=yes dst-address=45.60.0.0/16 log=no log-prefix="" to use ether4 which has input IP:192.168.42.2 as the pr...
I bought a new router to be used as an extender for my MT mini. The extender does not give an IP to the devices connected to it. I tried to connect the extender from another hotspot, the devices connected to the extender was getting IP from the hotspot. Is there anything adjustment to the wireless s...