MikroTik

dad2312

try to detach your m2 adapter => mpci because the lhgg radiator presses too much on the sim location of your adapter and causes this message.

even simpler dismantle the radiator from the lhgg and test again

dad2312

Sorry i report a problem with PwrLine. After upgrade to 6.48, my two devices (model PL7411-2nD) don't pair. After reboot, change settings, more and more.. nothing. Downgrade to long term, all change to ok. Untill 6.47.8 everything works fine. ps: ether1, pwr-line1, wlan (off) all on bridge-local wi...

dad2312

Also try disabling internet detection:
Code: Select all
/interface detect-internet
set detect-interface-list=none

thanks, it works for me with same problem "DHCP offering lease without success to itself"

dad2312

Thank You Sob works !!

question : we can't make theses rules via winbox only via terminal ?

/routing table
add fib name=vpn
/ip route
add dst-address=0.0.0.0/0 gateway=212.58.77.1 routing-table=vpn

dad2312

Thank Sob, i tried several things without success. I use ROS 7.1 beta2. i try this : /interface list add comment=defconf name=WAN add comment=defconf name=LAN add name=VPN /ip vrf add list=all name=main add list=LAN name=LAN add list=VPN name=VPN /ip firewall mangle add action=accept chain=input in-...

dad2312

Hello I use LTE connexion with LHGLTE6 in passtrough with hapac2 and i want to use my vpn on hapac2 just for incoming connexion from outside and all other connexion from LAN have to go trough wan ( lte provider) connexion. if my distance route vpn is the first (distance =1) all works but of course a...

dad2312

We always keep working on new products. In future, we will also have outdoor LTE products with Gigabit.

dad2312

Antenna lte improve signal quality (even if you are close to the tower) and make a significative difference. it is so complicate or so expensive to put 1Gbs port on sxt lte or lhg lte ?

dad2312

Good point. So when is a Gigabit LHG LTE12 coming out?

+1

dad2312

Any SXT or LHG device with LTE12 and 10/100/1000 lan ports soon?

+1

dad2312

Have you upgrade the last firmware ?

interface lte firmware-upgrade lte1 upgrade=yes

dad2312

May be it's your operator who renew your ip ? (you can see that in the log). Mine change my ip every 12h ...

dad2312

dad2312

You need EARFCN and PCI

/interface lte at-chat lte1 input="AT*Cell=2,3,,EARFCN",PCI"

you can see these informations with :
\interface lte> cell-monitor
number: lte1

dad2312

LHG don't recognise your sim ?

check if you have put your sim card the right way round (and not pushed it too far)

can you publish the result of
new terminal
admin@.........>interface lte info lte1

dad2312

Good job Sib !!

cqi is very fluctue, may be you can reach a better RSRQ (> -10) with a good antenna position or try another relay.

dad2312

You created VLAN 2 for LTE modem management on the RB-LTE connection but then you made VLAN 2 member of same L2 domain as normal LAN: Yes, i make that just for LHG LTE has an ip gave by the bridge et can go to internet (to update automaticaly by script, send email etc...). Ok i can make a bridge wi...

dad2312

why ether 1 ether 2 and ether 3 have the same adress ? /ip address add address=192.168.1.254/24 comment=defconf interface=ether1 network=\ 192.168.1.0 add address=192.168.1.254/24 interface=ether2 network=192.168.1.0 add address=192.168.1.254/24 disabled=yes interface=ether3 network=\ 192.168.1.0 it...

dad2312

thank you, but i don't understand is it not exactly what i make ?

Acutaly the 2 lte are in passtrough mode and all (DHCP, firewall, routing....) is manage by HAPAC2.

dad2312

Ok Thank you Mkx I change name of ether1 by wan1 and ether2 by wan2 (both port receive the 2 ISP), they are not in the LAN. I have delete management wan1 and management wan2 from LAN interface list (it was a try for other thing) I have 2 LHG LTE with passtrough and i need manage it then i have 2 VLA...

dad2312

I use load balancing with 2 LTE, it works good, but i have lots of drop packet not cot coming from LAN. Then i think there's something bad in my config. Can you help me ? Capture.JPG Here's the config /interface bridge add admin-mac=74:4D:28:CB:53:12 auto-mac=no comment=defconf fast-forward=no \ nam...

dad2312

We need LHGR + R11e-LTE6 with 1GbE port - currently SXTR with bonding have 2xFE but LHGR still have a bottleneck to FE 2CA for 1+3 and 1+7 and 3+7 - currently only 3+7 :( LGHR with corrected 700 and 900Mhz Gain - currently works better with inverted antenna at 180°. Only 800Mhz works straight forwa...

dad2312

Bonding question I have SXTR LTE on roof, and Rb750gr3 in house, want to go over 100mbps between them with 2 interfaces. I make bonding eth1 and eth2 on no default configuration,on both routers, assign ip adress on bonding interface SXTR 192.168.88.1 and Rb750gr3 192.168.88.2 All ok, ping work, Rb7...

dad2312

ah ah ah !! oh oh oh !!

works great SiB !!

thank you again !!!

dad2312

Thanks again SiB ! i have to be more patient....

I test that and i make a return on this post !

an other beer for SiB please !

dad2312

Thanks Sib, but i understand i'm very bad to explain the situation. I do this drawing in attach file (I hope it's better to understand what i want) schéma load balancing.jpg i think my problem is on route : i try to replace ip gateway in route list by "wan1" but internet works very slowly ...

dad2312

I don't know make routing filter...

Load balancing works good for me but with double nat and i would like make bridge mode or DMZ from isp routers to manage all on the MK router

exemple with 3 LTE connexion (download for each : 150/70/90)

loadbalancingx3.JPG

dad2312

. At LHGR R the best ways is use passthrough mode and do all MultiWan on main router. Hello SiB how use passtrough with LHG R LTE to make load balancing ? In PCC load balancing : You have to make route to ping wan gateway but how make that if your gateway is dynamic and trough CGNAT (lte) ? Actualy...

dad2312

We need LHGR + R11e-LTE6 with
1GbE port - currently even SXTR with bonding at 2xFE have a bottleneck to FE at CPU

+1
1GbE port
add B28
and in my dream a cat19 modem

dad2312

dad2312 i have this config on all my LHG / SXT a comment ? This is not proper post for this question and you should try open new one. . /interface bridge add name=bridge1 I always use a mac-address generator in every new EoIP interface to setup admin-mac in every bridge who have arp enable. . /inte...

dad2312

@SiB i have this config on all my LHG / SXT a comment ? interface list WAN=internet /interface lte set [ find ] band=3,7 mac-address=AC:50:43:1A:EE:FD mtu=1480 name=lte1 network-mode=lte /interface bridge add name=bridge1 /interface ethernet set [ find default-name=ether1 ] mac-address=74:4D:28:4D:0...

dad2312

Check this .... https://forum.mikrotik.com/viewtopic.php?f=2&t=156318 Thanks all ethernet port is on auto negociation and show 100Mb/s full duplex, i try to force 100Mb/s (even if the post tell you don't have to do this if you let over device on auto negociation => on my modem i can't touch thi...

dad2312

Great Values SiB

Your test answers my question. You don't loose speed ping with your lte6. I don't think there is a difference between SXT lte6 and LHT lte6, so it's probably the relationship between my LHG LTE6 and my antenna relay that makes me lose a bit ping speed

thanks SiB

dad2312

Hello
No..

dad2312

You can Try to point another relay antenna, LHG LTE is one of the best antennas I know (I already hooked up a relay antenna at 21 km: speed 8 Mbs down / 1 Mbs up)

dad2312

Currently these are my readings; RSSI -52 dBm RSRP -83 dBm RSRQ -9.5 dB SINR 21 dB CQI 15 You have great value (may be just RSRQ a bit high compare to other value it have to be near -5dB but at your level there is non influence of your network speed ) with these values the only explanation is too m...

dad2312

ok i have the answer,

i test huawei b715s with other stuff (not mikrotik) on ethernet
when other device (like connect tv) have 100 Mb ethernet i loose more half on bandwidh
when other device have 1Gbs ethernet i loose nothing

issue come from huawei

thanks to all

dad2312

Thanks SiB

i ask again because it seems you d'ont have receive yet your LHG LTE6 when i ask first time..

i have already test LHT LTE4 and LHG LTE6 with
- same lte band, same cell, same firmware, same emplacement, same config etc.... and i loose speed ping with LHT LTE6.

dad2312

@SiB

Hello SiB

have you noticed with your LHG LTE6 a loss of Ping speed compared to LTE 4?

dad2312

Hi, I have had LHG LTE6 kit here in UK on EE for a few months now and the last few days the download and upload speeds have dropped from 80Mbs / 40Mbs down to no greater than 18Mbs / 5Mbs now obviously this is still not too bad but it doesn't help me when demonstrating to potential customers. Could...

dad2312

My little quick and durty test setup (ROS versions different and taken off a WLAN-ptp network) I connected a "hAPac2" - to -" hAP ac Lite" - to - "mAP Lite". Connection from hAP ac2 to mAP Lite passes over the hAP ac Lite switch. Only the hAP ac2 has 1Gbps interfaces. ...

dad2312

Yes it is because of performance of hAP AC Lite, look ate the picture below! With 40-45 Mbps it goes to 95-100% Processor usage! So cannot support more traffic! I have more than 80 of those routers and is the same thing! I use this for clients that need under 20Mbps and need WiFi just for small are...

dad2312

@dad2312
On your mtik - what speed do you see in ethernet ports status, is it 100 Mbps Full Duplex ? Is Hw. Offload activated on bridge ports (look at Bridge/Ports for big H next to port numbers) ?

i confirm all is on 100Mbs full duplex and HW offload activated

bridge.JPG

dad2312

Fast ethernet negotiation can fall back to half duplex. Worst case is when one side is half duplex and the other is full duplex. Mikrotik interface status shows the duplex state of the interface. If the other side does not answer (eg because full/half negotiation is not implemented, or disturbed ne...

dad2312

Might be caused by the wireless settings...how did you configure wireless?

all test via ethernet

wireless no configure

dad2312

after several test, i assume is due to the performance of HAP AC lite here's my test : configuration for all device nothing else but : reset configuration with no default configuration setup a bridge with all ports dhcp clients on the brigde all test via ethernet huawei modem b715s : speedtest : 120...

dad2312

is it due to the performance of HAP AC ?
No...

an idee maybe ?

dad2312

Hello i want my HAP AC lite 6.41 like simple switch. I have make a very simple config wich works : nothing else but : reset configuration with no default configuration setup a bridge with all ports dhcp clients on the brigde it works but i loose the half of my bandwidth only on download (test with e...

dad2312

dad2312 With LHG LTE cat4 ping is 40ms with LHG LTE cat6 i have 70ms (test make several days) test with mikrotik tools to 8.8.8.8 or 1.1.1.1 LOL. Please give me information what is spedicic modem in this Cat4. like R11e-[LTE | LTE-US | 4G ] and if you can do example from my r11e-lte6: here's LHG LT...

dad2312

What you mean? SXTR have got example 33ms to 1.1.1.1 but LHGR have 63ms or 3ms ? With LHG LTE cat4 ping is 40ms with LHG LTE cat6 i have 70ms (test make several days) test with mikrotik tools to 8.8.8.8 or 1.1.1.1 The best version of ROS now is 6.45.7 but on 6.46.x are some speaks like "slow wi...

dad2312

I also note that I lost 30ms of ping compared to LHG LTE Cat4 (exactly the same configuration in the same place with the same first band)
Do you make the same observation?

dad2312

dad2312 Thank you SiB ! Not sure i understand, where is the RestoreIntenet script ? Is the script restore Carrier aggregation if it lost ? I try to make just a copy/paste on Netwatch but i keep going to loose CA... . You welcome. . Not sure i understand, where is the RestoreIntenet script ? This is...

dad2312

I add some information. One time I do a table of possible 2xCA in EMEA Band's for EP06 and R11e-LTE6: opera_BBqucAL3cr.png Modem Firmware v20 is very often use the ca-band on normal and CellLock situation. Signal levels we see from a primary band. Both bands in my testing not give many acceleration...

dad2312

i noticed my LTE6 modem always connects to just 1 (highest) band at start, but later at download/stress it connects to 2nd. Dont know how exactly CA works, but maybe some BTS drops idle connections to don't hold resources?

LTE works like you say, CA begin only if it needed.

dad2312

I have got "SXTR rev2 & R11e-LTE6 kit" by 1 day. SIM are not up/down but a/b. 2CA works. Cell/SectorID lock works for primary band and second one "ca-band" works automatical. This lock is now save inside modem, we not must use modem-init. mspaint_qoO5jcUrxo.png It's inside h...

dad2312

I have 2 LHG LTE6 and I have more with CA (band 3 and 7) than only band 3 or band 7. But I notice when several clients are connected after a certain time aggregation does not work more and there is just one band left? if you disable and enable LTE the band aggregation comes back but not long? the 2 ...

dad2312

I see this problem the same day I configure the router. Now on some jobs the problem pops up a few days after I have left. Those ones... disabling the radio interface sometimes cures it. But the jobs where I see those messages right away... I have to change manufactures. Too many lost hours and cli...

Search found 57 matches