Am I missing something, because I can't see `container.npk` in extra packages for 7.1.1 nor for 7.2rc1?
Was it removed for now?

As a follow-up, it seems that fixing double IPv6 default route fixed things.
I did have some other intermittent issues, but it might have been something misconfigured on my side - once I got back to looking into it, ipv6 routing works now.

As follow-up, I tried to set up Hurricane Electric tunnel to see if routing will work via it, and that seems to work fine. Must be something specific to pppoe setup / BT? Somewhat confused because this used to work with ROS6. I guess I need to set up sniffer and look at the data inside pppoe for any...

Thank you for helping. I didn't notice duplicate default route myself, and disabling default route on DHCP client indeed fixed the issue. However I still can't see pings to global addresses working, it simply says timed out. I have tried to use torch on the pppoe interface to see if I can debug it, ...

I just realized that after upgrading my HAP AC2 to ROS 7.1 IPV6 doesn't seem to work anymore. It's quite strange actually - my uplink is BT pppoe, and I can successfully obtain ipv6 prefix from DHCP-PD. It also correctly advertises prefixes to local machines. I can successfully ping ipv6 addresses o...

Just to confirm, configuring pppoe on top of the bridge did improve the behavior drastically, it stays up rock solid and I didn't see any disconnects in a week now.
Thanks for help.

Thanks for advise.
Yes, those ethernet drops/reconnects are short, like 1 second each, so I guess ppp won't even notice.

Just tried to set it up, and was even able to move the cable between e4 & e5 without ppp noticing anything at all.
Will set up some monitoring and keep an eye on it.

As a follow-up, after a week and a bit - it's running much more stably on another port, though I still seen two ethernet link flip-flops (after moving wan link to e4 on 19th) Jan 25 07:44:58 router.lan interface,info e4-wan2 link down Jan 25 07:44:59 router.lan interface,info e4-wan2 link up (speed ...

Are there any updates on SWOS 2.12 and RSTP issues on CSS106-5G-1S switches?

Hi, I have strange issue after updating SWOS to 2.12, where RSTP stops working and will switch ports to discarding. I have first hit this issue back right after release of 2.12, but didn't have time to debug and just rolled it back. So now I have updated only one of the switches, and should be able ...

Just to confirm - it seems the whole affair was caused by bad ethernet port on HAP AC2. Moving pppoe wan connection onto another ethernet port things are running fine & stable for the last two days now. What is curious, that problematic ethernet port periodically detects link-up, even though it'...

It looks I have overlooked smoking gun when connecting via switch (and now via BT hut itself) - I'm still getting e5 ethernet connection flipping up and down randomly. Jan 15 01:51:24 router.lan interface,info e1-trunk link down Jan 15 01:51:24 router.lan interface,info e2-nas link down Jan 15 04:19...

Thanks for confirmation, though my ONT unit if from Huawei - HG8010H5-20. I must admit things are getting stranger by the day -- even connecting via BT hub lan side (acting as a switch), it still drops connection periodically. This basically leaves a problem either with ONT unit or PPPoE incompatibi...

Sadly switching to 100Mb full duplex doesn't seem to make any difference - link (and pppoe connection) dropped three times in about 1/2 day since I switched it to 100Mb. For connecting via hub - I guess it should work if I just use either BT hub or old VirginMedia box and plug both AC2 and optical u...

Thanks for advice. I don't have any spare dumb switches laying around, so will leave that option for later. Contractual WAN is 150Mb, but I can definitely live for couple of days with 100Mb. Will start with limiting the interface to 100Mb, and then maybe I can try to repurpose my old cable modem to ...

That twist with bridges-over-vlan is basically a hack. Mikrotik doesn't allow to set admin-mac on the VLAN interface. Normally windows uses MAC address of default gateway to identify different networks (and switch network-specific settings accordingly). Without those bridge-over-vlan it's behaving a...

Here's full config. # jan/10/2021 19:58:37 by RouterOS 6.48 # software id = SXYC-CSVI # # model = RBD52G-5HacD2HnD # serial number = 92F20957FD95 /caps-man channel add band=2ghz-g/n control-channel-width=20mhz frequency=2412,2437,2462 name=\ ch-2.4g reselect-interval=30m save-selected=yes skip-dfs-c...

Sorry, forgot to mention it.
I did try connecting with another cable, it didn't help.
The only other idea I have is to use another ehternet port, but it's quite a lot of config changes, because of VLAN setup.

Hi, I'm having strange issues trying to use HAP AC2 as router with BT Full Fibre broadband. I did set it all up successfully, but every once in a while there are short (about 1 minute) outages. I didn't notice any pattern in the outages -- sometime it will work successfully for multiple days, other ...

So, just to summarize what I tried and what worked (or not): * Both HAP AC2 and RB260GS switches (product code CSS106, based on AR8327 switch chip) seem to ignore forwarding overrides table when set up to do vlan switching on the chip. * Both appear to respect switch rules (called ACL in the SwOS). ...

Thanks for reply. From a little googling, it seems that switches I found with support for PVLAN are from very different price/size bracket. I'll try in the evening to set up some form of port isolation using switch level rules, it seems to work on both switches & HAP ac2, and should be HW-accele...

Hmm, the reason I thought about brdige filtering - I want default route on the guest vlans to have different MAC from internal network. The reason being, windows uses MAC address of default route to recognize networks, and stores network parameters (like public / private, name, etc) per-MAC. From wh...

I was afraid of that answer :/ I don't question that switches & HAP can do it, just feels as massive overcomplication. 10 more vlans, set them up on HAP AC and two switches (those are even worse with web-page only interface). Then corresponding vlan interfaces, single--vlan-port bridges to chang...

Hi, I need a bit of advise on how to isolate hosts inside vlan. My setup -- I have hap AC2 working as internet router, a bunch of devices connected directly to it and then another few via a couple of mikrotik managed switches (RB260GS). I have set up a couple of vlans, to separate my nas & PCs f...

Thanks for your reply. Regarding #2, this "interface bridge filter" rule was generated by one of the QuickSet script. Not sure right now which one it was though. It was blocking second router from getting the address via DHCP, that's why it had ip address set manually on the xlink interfac...

And second router: Router 2 (HAP wireless AP & some more ethernet devices) /interface wireless set [ find default-name=wlan1 ] band=2ghz-b/g/n mode=ap-bridge set [ find default-name=wlan2 ] band=5ghz-a/n/ac mode=ap-bridge /interface bridge add name=br1 /interface bridge filter add action=drop ch...

Adding current setup as separate post, for some reason formatting was glitching: Router 1 (HEX, bunch of ethernet devices + WAN uplink) /interface bridge add name=br1 /ip pool add name=dhcp ranges=192.168.123.50-192.168.123.200 /ip dhcp-server add address-pool=dhcp disabled=no interface=br1 name=dhc...

Hello, I'm trying to set up small network using two mikrotik routers. So far I think I got the basic setup working -- machines can see each other and wifi is working. On the first router, one port is designated as WAN (with QuickSet generated firewall), and all other ports are connected together int...