RB4011 after update lost ovpn.
Connecting
Established
Disconndcted

<user> detect UNKNOWN
I am not sure how was before
Any ideas?

I have the same OVPN-Issue, with 7.10 and 7.10.1.

I played around a little bit and the following solution worked for me (but I do not really understand it, because the VLANs Tab is empty). SW1: This is the definition in VLAN-Tab: * Trunk-Ports are Port 7+8 and SPF 1+2, they are in VLAN 1. * Access-Ports are Ports 1-6, where I define the VLAN. VLANs...

Hello, Router connects to SW-1 port 7 => Correct SW-1 provides DHCP-Addresses and access on Port 1-6. SW-2 provides DHCP-Addresses and access on Port 1-6, when SW-1 and SW-2 are connected via Gig-E-Trunk (E.g. Eth8). SW-2 DOES NOT provides DHCP-Addresses and access on Port 1-6 to Router, when SW-1 a...

Hello, I have two CSS610-8G-S2+ which I want to connect via SFP+ Fiber link. My Router is connected to Switch1 via Trunk on port 7. This is working fine, I can get IPs from DHCP from several VLANs on Switch1. If I try the same on Switch2, I do not get DHCP-IPs, if I use the SFP+ Ports, if I use an 1...

But if I receive the Gateway via DHCP, how should I configure this? Is it required to change this manually every time?

Hello, I'm getting from my provider the IP of my WAN-Port via DHCP (e.g. 20.1.1.2/24) and I have a default route in my main VRF to the provided gateway (20.1.1.1). Now I would like to add to my VRF "Guest" a default route, that the internet is reachable from this VRF, this is done via /ip ...

Hello, Has someone an idea, how I can upgrade e.g. my Pi-Hole-Container running on Mikrotik 7.5? I'm using as Remote-Image = pihole/pihole:latest and when I open the WebInterface I can see that there is an Update available: Docker Tag 2022.08.1 Pi-hole v5.11.4 · Update available! FTL v5.16.3 · Updat...

Hello, I have logevents like this: Jan 01 00:00:00 Router %MIKROTIKVPN: VPNUSER logged out, 2426 8798275 307780041 143841 209279 from 1.2.3.4 I tried to find information about the 5 numbers, could someone tell me, what this is? I think this are bytes in, bytes out, packets in, packet out and the las...

You are right, normally I'm only logging the drops/rejects, but I in some cases I'm interested in the acceppts, for example who is trying to connect to the VPN to run reports based on this data.

If I activate logging for a rule, I would like to see the ACTION at the log, without adding prefixes. Otherwise I don't know, if the packet is dropped, rejected or accepted.

Yes, the Prefix would be possible, but should this not be part auf the default Logging Template, where you have the protocol, the source + destination?
Because if I want a logging, I need to add this to every rule and every device, this would be a lot of work to change.

Hello, If I look at the firewall log entries, I only see the following: input: in:Eth1 WAN out:(unknown 0), src-mac 34:da:b7:c3:6d:1f, proto TCP (ACK,FIN), 142.250.1.1:443->10.0.1.1:37206, len 52 But I'm missing the information, if this event was accepted or blocked or rejected (the ACTION). Is ther...

Hello, I have a question, how can a make a default route of my "VRF Guest" if I have only one public internet address. Configuration: WAN-Interface: DHCP Client which gets an IP Address (e.g. 200.200.200.200) and a gateway (e.g. 200.200.200.1). NAT: Chain=srcnat Out-Interface=WAN-Interface...

It does sound like a bug, you could report it to Mikrotik support.

I reported the issue to MicroTik.

Thanks for the reply. I'm using the loopback-interfaces to send the packets and what I can see at the recieving device (UserManager & GRE Tunnel end point), the Router/UserManager receives the packet with the correct loopback ip addresses; I also see a successful authentication at the UserManage...

Configuration: R1 WAN-IP 1.2.3.4/24 GRE-Tunnel-IP 10.0.0.1/30 (1.2.3.4 -> 5.6.7.8 ) Management-IP 192.168.0.1/32 R2 WAN-IP 5.6.7.8/24 GRE-Tunnel-IP 10.0.0.2/30 (5.6.7.8 -> 1.2.3.4 ) Management-IP 192.168.0.2/32 Management-IP is proviced via OSPF and this is working fine and I can ping the R1-Managem...

Hello, I have two microtik router and these routers are connected via GRE-Tunnel. Router1 has the User Manager running. Router 2 uses the Radius Server of Router1 and I tried to send the Radius Request from the Management-Interface of Router2 to the Management-Interface of Router1, Router1 receives ...

Hello, I would like to know, how much traffic my LAN-Interfaces and my WLAN-Interfaces produce, therefore I created "Mangle Rules with passthrough" as shown in some tutorials. The LAN & WLAN Interfaces are at the same Bridge, therefore I created "Interface Lists" for with the...