thanks!!

Dirk111

Hi on a camping site I had a point to multipoint 5GHz, but is was a bottle neck (100 Mbps). Multipoint AP on RB411AR. On the low 5GHz frequencies it worked! It was replaced by 4 SXTsq communicating with 4 individual hotspots (RB411AR: hotspot OB WLAN1 2.4 and uplink WLAN2 R52nM on 5GHz) PROBLEM: The...

hello since 2007 we have Mikrotik hotspots on camping sites. In those days there were laptops and even some tablets. No problems! It worked. Now... smartphones, allways connecting to check mails, whatsapp, Facebook etc. ... Our problem: we can see when they connect, but the idle time out keeps reset...

what do I miss here??
userman running on RB1100AHx4 Dude ROS V6.43.11

User tries to login on hotspot 10.100.1.231/24 (public address 192.168.200.254/24): user not found
and 2 minutes later: authorization succes

same problem on another hotspot...

thanks!
dirk111

tomorrow I'l be testing this last solution in ROS 6.42, but this time in "real life" Here (today) in the work shop everything went OK. There should be a real change (ROS 6.40 vs 6.42)... So I use interface/bridge add name XX ig.snoop=no prot.mode=none interface/bridge add name YY ig.snoop=...

switched to ROS 6.42.1 port bridging with hw-offload: works . Should be layer 2 switching... Since RouterOS v6.40rc29 there are user interface changes which convert RouterBoard master-port configuration into a bridge with hardware offloading. From now on bridges will handle all Layer2 forwarding and...

I have little experience with VLAN's... In the manual of the CRS1xx I found this: Dynamic reserved VLAN entries (VLAN4091; VLAN4090; VLAN4089; etc.) are created in CRS switch when switched port groups are added by setting new master-ports. These VLANs are necessary for internal operation and have lo...

hello is there a better solution for this task: - incoming fiber from VDSL modem/router (connected to SFP9) - fiber to next building (connected to SFP10) - ether 1-4 as "outlets" for clients - set ether1,ether2,ether3,ether4,sfp10 master-port=sfp9 and the same CRS112-8G-4S-IN serves for a ...

Hi

PROBLEM SOLVED!!
I also needed the support of Mikrotik Support...

To add a user, you MUST issue the command user manager user ADD USER = "TEST"
and then you can answer "admin" on the question "customer"
and user TEST is created

Thanks everyone!
Dirk111

thanks for the reply but: I use ROS 4.60 (or higher) and even in a Terminal (Winbox or direct RS232 connection) I get, when trying to add an new user: customer: admin failure: username is required I've tried al lot of combinations to answer the question customer: ..., quotes, usernames... Does it ma...

while debugging my program... it sends this to the RB Send("/tool/user-manager/user/add"); Send("=customer=admin"); Send("=name=" + varName); Send("=password=" + varPassw, true); reading the answer, I get: "!trap=message=unknown parameter !done" must...

hello, using RB for many years now (RB112, RB532...), but I'm new to User Manager. I'm writing a programm in c# to control UM, running on a RB433 (will be replaced by a RB1100AHx4 Dude Edition). List users or profiles ...: OK adding a customer: works fine!! add user, even in a Terminal: problem!! /t...

Thank you.

It seems to work now.

On the wlan side we are usig DHCP for the clients to connect. IP address is 192.168.101.1/24 DHCP Pool 192.168.101.10 - 192.168.101.250 ether1 is 10.100.1.249/24 and is eventually connected to the internet (through 10.100.1.254). The problem we have now is that routing doesn't work so the wlan clien...

I use the mikrotik stuff to build hotspots and beam connections. Now I want to build a simple broadband router: ethernet in and 2.4 WLAN to the clients (RouterBoard500 + 1 R52). DHCP + NAT. Just like the simple SOHO WLAN routers you can buy.... . Do not need WEP, WPA .... The WLAN broadband router h...