Almost all cards with AR5213 and AR5414 chip, it means all cards with A/G-Turbo. Normally non-N chispet cards. Now only R52H from MT offer.Hi......
which mikrotik Mini PCI card that support 40Mhz Turbo Channel Width on 2GHz Band
/ip dhcp-ser ex
This problem still exists. I have it yestarday with a couple of RB912 with external cards, and find a way to repair that.Who cares anymore?
/system routerboard settings set init-delay=2
Is it real test? Do you really achive on this link more than 1,4Gbps!?!?
If we talk about your current configuration, just because your VLANs aren't on a bridge.Thanks a lot.
And can you explain why I can't connect if I set vlan-mode=use-tag in the access-list?
Yes.Ok, so if I understand right
I have to put the VLANs to the bridge and than tag the datapath?
Is that better?
Can you also explain why?
It is something to be proudNot of the physical equipment, but I can share point A and B
I can share a screenshots of the signal and distance
Possible with new wir-rep package.Related to this, I would like to be able to specify (enable or disable) specific rates on wireless interfaces managed by CAPsMAN.
It's like an elephant and a refrigerator. You can do it in three steps:I will generalize my question: How to change some option (property) for CAP wireless interface that isn't supported by CAPsMAN ?
Respect!The longest link we have is about 150km.
Using RBNetmetal 5's and the biggest dishes ubnt makes.
Signal is -57/-55 getting about 40-60Mbps
AES - wlan card (hardware accelerated AES encryption is in almost all chips)Are you sure that the encryption is done in cpu and not in wlan card?
So you have to mannualy exclude that addresses, using ranges: 188.8.131.52-10.200.0.9; 10.200.0.11-10.200.0.83 and so on.i'm using mikrotik router,and I'v dhcp server there, i wanna exclude 10.200.0.10 10.200.0.84 on mikrotik
Sorry for my rude reply.You nowhere wrote if you have this problem with this latest swos firmware?
Therefore I asked you if you use swos 2.14?
http://lmgtfy.com/?q=mikrotik+swosWith swos 1.14?
NoIncluded in new wireless repeater package?
General bug, I see it in every platforms that we have.IP----> Web Proxy---------> General-------> Port show : 0 from ROS 6.34, x86, (not solve this problem)
<html> <head> <meta http-equiv="refresh" content="0; url=login?username=user&password=pass&dst=http://landing.page.com/"> <meta http-equiv="pragma" content="no-cache"> <meta http-equiv="expires" content="-1"> </head> <body></body> </html>
Distance about 400m.Hi czolo,Some tests from our network:
If you like it, give me some Karma points
What distance did you have there and which antennas have you used ?
This is not a problem. You can use PoE-injector and short RJ45 patchcordWe need 3 chain mimo with JACK
All products with SFP connector should have a DC jack connector.
It will be hard to do, because QCA9882 is 2x2 onlyI should have Compex 802.11ac QC9882 mini pci-e card Monday. Plan to install in RB912UAG-2HPnD as indoor AP with 3 MT 3dbi antenna. Only client I have is Lenovo laptop with built in Intel ac card. Will report back!
You can try RB912 + r11e-5HnD. You can put it all into:Hello,
We have a hotel with 3 floors and 14 rooms on each one. What is the best AP with also DualBand (2,4 + 5GHz).
Ther is something like this:Is there an enclosure available designed for this device?
Hi Normis. Thanks for this PDF.New product slides: http://mum.mikrotik.com/presentations/IT14/it14.pdf
Yes, if You have such big difference between chain 0/1, you can try to set it another way.I think I found the problem.
During the installation of antennas have been inverted channels(chain0,chain1)
Maybe this can help you:Dear all.
Can someone explain me, how to setup 60ghz channels on any RBxx with any AR92xx on any ROS???