I noticed that when using a CRS317 as Port Controller and a CRS309 as Port Extender, once the link between the two devices fails the Port Controller completely stops forwarding and is not accessible anymore. It stays in the locked up state until the link to the Port Extender is restored. This behavi...

Also all free disk space is gone. Right after update it showed 8kB free, then I deleted two autosupouts to get at least something, but instead ended with nothing: Thats actually fine on my side: free-hdd-space: 2732.0KiB total-hdd-space: 15.9MiB but i did not do any file based operations so far. wi...

I'm testing beta3 on my CRS309-1G-8S+, the update went smooth. One thing i instantly noticed is that /export never terminates. Tried to reset to an empty configuration, same thing. When i run /export verbose the last thing that gets displayed is /radius incoming set accept=no port=3799 and then it h...

error=unsupported certificate purpose

this.

the output of `openssl x509 -in C:\\Users\\someone\\OpenVPN\\config\\cert_export_MY-CA.crt -text` would be helpful, to see what attributes are set in the certificate.

Hi, I re-ran the test and during the test the connection list was empty as expected but throughput was even worse this time, around 2.2Gbit. Then, just to be sure, i net-installed beta2 again to get a completely fresh setup, reapplied the config and wonder why, now i can push up to 9Gbit through the...

Hi,
for IPv4 this is certainly true. For IPv6 (in the future) at least ICMP6 'packet too big' will be needed. For IPv4 'packet too big' would be nice as well, as the switch chip surely doesn't do packet fragmentation, or does it?

Hi, @skylark: I've sent in a supout.rif. @raimondsp: Yes, 172.17.30.1 and 192.168.89.1 are the same device. Both interfaces are configured the same in terms of firewall rules, no QoS happens on the device. Another question thats popped up, if L3HW offloading is enabled, the CRS309 does not show up i...

This is an iperf on my regular infrastructure: $ iperf3 -P10 -p 12345 -c 172.17.20.10 ... [ ID] Interval Transfer Bandwidth [ 4] 0.00-10.00 sec 762 MBytes 639 Mbits/sec sender [ 4] 0.00-10.00 sec 762 MBytes 639 Mbits/sec receiver [ 6] 0.00-10.00 sec 758 MBytes 636 Mbits/sec sender [ 6] 0.00-10.00 se...

Yes, I have seen that as well and corrected earlier.
So you are saying nothing is basically wrong with that config? I'll then put the device in an isolated environment, not connected to existing infrastructure and do some more debugging. I'll come back if i figure something out.
Thanks for the help.

As i said in my first post, on my regular infrastructure I am able to push ~10Gbits with the same Endpoints and an MTU of 1450. It's not like I would try to saturate the Link with 40byte packages.

Hi, so i did try the same setup with the default MTU: /interface ethernet set [ find default-name=ether1 ] l2mtu=1592 set [ find default-name=sfp-sfpplus1 ] l2mtu=1592 set [ find default-name=sfp-sfpplus2 ] l2mtu=1592 set [ find default-name=sfp-sfpplus3 ] l2mtu=1592 set [ find default-name=sfp-sfpp...

I finally found some time to play with the new beta and L3HW offloading in particular. I did configure two networks, one attached to my client and the other pointing into my regular infrastructure, added a route and activated l3hw offloading. a few unexpected reboots later (yes i know, console only ...

well, that's quite unfortunate. i did try the setup running on ROSv7, but there i'm not able to add any ipipv6 tunnel interface, as it fails for unknown reason in any possible configuration. a bit unstable still. also, i haven't come across that piece of documentation, where are you quoting from? th...

Hi, thank you for your answer. this does not seam to work for the dhcpv6-client. when i add this script to the dhcpv6-client: :log info [:typeof $options]; :log info ($options); :log info [:typeof ($options->"40")]; :log info ($options->"40"); :log info [:typeof ($options->"...

The manual doesn't say anything about that, exactly my reason to ask here (:
Shouldn't this be a common use case, receiving configuration data via dhcp(v6)?

Hi, I have a ds-lite setup, where v4 is tunneled via ipipv6. the endpoint of the tunnel is received as a dns name via a dhcp-option. So as a client option i'm setting /ipv6 dhcp-client option add code=6 name=option_req value=0x001100170040 adding 0x0011 for OPTION_VENDOR_CLASS - just for funz 0x0017...

VLAN tagging seems to be broken: Version number (if the issue is upgrade related, specify which version was installed before as well); v7.1beta1 before v6.74.1 Router's model; RB951G-2HnD Steps to reproduce the issue; create a bridge and add ports; create vlan interface on top; add dhcp client to in...