MikroTik

galvesribeiro

@Guscht thanks for the reply. I had used 100G Dell switches in another situation and even they use MLAG so I don't see a problem. Nonetheless, as you see from the thread, @sindy already proposed a better and simpler solution, which is what we are going to follow. It is true that MT doesn't implement...

galvesribeiro

Just a terminological remark, the abbrevaiation NIC is typically used for a single Ethernet interface even if it is physically located on a multi-port plug-in card. Sorry, pardon the language :D What I am saying is what I am saying. I can't agree or disagree with your comparison to Hyper-V because ...

galvesribeiro

Hello @sindy, thanks for the reply. traffic between two IP addresses in the same subnet does not need to go up to the routers because, scrictly speaking, it is not routed. The behavior is the same as if there was a single switch, the Ethernet frames carrying those IP packets are L2-forwarded/bridged...

galvesribeiro

Hello guys! I have a particular scenario that I'm working on which I got stuck while reading the documentation: Screenshot 2023-11-10 at 3.17.50 PM.png The applications are running inside a VMWare cluster of 4 machines. Each machine has 2x Mellanox ConnectX-4 Dual port NICs. Each NIC, is supposed to...

galvesribeiro

Sorry, I've missed your reply @raimondsp. Here is the output (masked public IPs) /interface export hide-sensitive # aug/08/2022 07:33:36 by RouterOS 7.4 # model = CCR2216-1G-12XS-2XQ /interface bridge add admin-mac=02:4A:B4:F6:2D:A4 auto-mac=no ingress-filtering=no name=bridge-LAN vlan-filtering=yes...

galvesribeiro

i see auto-negotiation disabled, maybe try auto, also check the other end settings

Tried as well, no luck :/

galvesribeiro

yes is a suggestion to separate ether-Management from bridge to see if that improve the situation

I've removed it from the bridge. There is no physical link still (no blinking lights when connecting the cable). That is the same behavior as if it were in the bridge :/

Any suggestion?

galvesribeiro

kepp in mind ether-Management is a separated interface for management purposes only ether-Management is bridged to other interfaces? being bridged or not change the situation? Thanks for the reply @chechito. Yes, it was bridged but nothing were connected to it before. Only when we had issues that b...

galvesribeiro

Hello folks! I've enabled HW offload on our brand new CCR2216-1G-12XS-2XQ including the L3 support to all ports but the uplink/internet ports and the eth1/Management port. However, as soon as I enable the L3 HW offload the eth1/Management port just stop working. It appear to me as "enabled"...

galvesribeiro

I have the same issue. I'm using 7.3.1 (latest stable as of now) and I had the management port with no link after enabled the HW offload. My bridge has 8 VLANs as well. I've disabled the HW offload, rebooted the router, but still, no link on the management port (eth1). I'm using a CCR2216-1G-12XS-2X...

galvesribeiro

Hello! With the advent of the new 100GbE line of products (CCR2216-1G-12XS-2XQ / CRS504-4XQ-IN / CRS518-16XS-2XQ) being advertised as Enterprise and Data Center products, companies with serious Enterprise and Data Center workloads (like ourselves) started to using those devices to drive their busine...

galvesribeiro

After mikrtoik support reply i can tell that MLAG on v7.1 is working The problem was the missing TAG on the PEER port exchange VLAN (in my case the qfsplus1) On VLAN 3000 the peer port must also be tagged, unfortunately it was missing on the config so when the exchange had to take place between two...

galvesribeiro

Just to update everyone. Indeed, the disk HAS to be SATA in order for it to work (at least by the time I made this post). Got new disks Today and was able to format both as FAT32 just fine. Now I'm looking forward for the containers support to go to stable channel so we can put the images/volumes on...

galvesribeiro

ccr2116 m.2 slot is pci express (nvme or ahci? who knows) ccr2216 m.2 stots are sata being that they use the same SOC why the difference? That is interesting question that I hope some folks from Mikrotik would come here and shed some light later. But I would expect that their most high end (and exp...

galvesribeiro

Hi,

Samsung 860 EVO SATA in the product video. Samsung 980 PRO is NVMe.

OMG! How did I missed that?!?! I only saw the Samsung and M.2 part and haven't noted that difference.

Thanks A LOT for that. I'm sourcing 2 860 EVO SATA now. Will try again tomorrow and report back.

Thank you!

galvesribeiro

MikroTik has not specified if this m.2 slot supports nvme modern disks nor has published a validated list of disks or max capacity supported i think is necessary to establish a compatibility matrix because some references support m.2 sata and other m.2 pci express (without specifying protocol AHCI ...

galvesribeiro

Hello! We've just got our branch new CCR2216-1G-12XS-2XQ. After setting it up we added 2 Samsung M.2 SSD 980 sticks with 500GB each to it and powered it on. However, they doesn't appear on `/disk print`. Do we have to do anything to enable those disks? Thanks! Any light would be appreciated. Best re...

galvesribeiro

Hey @carragom, I have the exactly same situation. On Windows 10/11 I get all the routes and the policy being generated is from 0.0.0.0/0 to whatever network was defined on the "Address Pool" at the IPSec Mode Config. All traffic flow just as expected. However, on MacOS and iOS, it generate...

galvesribeiro

On the same boat here but with GoDaddy as the CA. I can download the CRL from the URLs on both HTTP and HTTPS just fine. However, MikroTik keeps insisting it is invalid... Tried to use fetch to pull it but it shows 0KiB downloaded, no errors...

Anyone has any clue?

galvesribeiro

@hkusulja after 4 hours with Azure Premier support, we were able to get both IPSec tunnels up with Mikrotik and the BGP connection stablished on both tunnels as well Today. I'm receiving the VNet routes advertised by Azure and they appear both in my Routes table. However, None of the routes I'm adve...

galvesribeiro

First of all a HUGE THANK YOU to the post Author. I've be battling with AWS CCR2004 and v7.1.5 for a while and I finally got it to work after finding this post with BGP. I've used a combination of these methods: Sep 2020 https://medium.com/@autogun/aws-site-to-site-vpn-with-mikrotik-routeros-5977ca5...

galvesribeiro

I've successfully made it work with BGP finally but the problem remain the same... Asymmetric routing with the two tunnels. AWS expect only 1 SA pair per tunnel so packets can come and go both ways when needed. If we se the same policy to have 2 peers, it fail to send/receive packets and eventually ...

galvesribeiro

Thanks for the reply Diego. I've tried to setup it with BGP before, but never had success as the tunnel never came up. I was on the latest v7 RourterOS but all the guides I've found were using v6.x then I had downgraded but still, no success on the AWS side. The I tried to use the regular policy-bas...

galvesribeiro

Hello folks! I've recently set up on AWS an IPSec site-to-site VPN (Virtual Private Gateway, not the Transit Gateway) with my CCR2004 (v6.49.5). AWS provide us with two tunnels per VPN connection so we can have redundancy on the connection. I've added both peers and its policies as you may see here:...

galvesribeiro

Folks, had anyone had a poor customer support experience with @CarlitoxxPro ? They where fast to put the order and collect the money, but it is about a week that I received their GPON stick and I'm trying to contact them for support and they just don't reply emails... Tried to reach them by Telegram...

galvesribeiro

Hummm so the restart is related to the change on the SN? I don't know, not sure to be honest. The thing is that even if I leave it untouched, with its original value, it does reboot when I plug the fiber. If I leave the fiber disconnected it never reboots. The only thing related to the firmware that...

galvesribeiro

Okey... Got O5 but can't get PPoE to pass thru it... One thing I note is that after a few seconds after connected the fiber on UF-Instant, looks like omci_app dies for whatever reason, and then some watchdog reboot the SFP module a few seconds later. Not sure it is related to the lack of the serial ...

galvesribeiro

That is what I feared as there is no way to do that by SSH that I know of.

Im not sure, because other data is persistent...

galvesribeiro

Progress... SSH enabled with `/bin/dropbear -R &`... Now need to find which files need to be patched in order to make the tool to work correctly and change SLID, MAC, Serial, etc... Good Work Do you think it is possible to patch the UFiber Instant and change SN so that it survives a reboot? Yes...

galvesribeiro

Progress... SSH enabled with `/bin/dropbear -R &`...

Now need to find which files need to be patched in order to make the tool to work correctly and change SLID, MAC, Serial, etc...

galvesribeiro

Aha! I've got a TP-Link media converter and plugged the UF-Instant to it and now I can access the telnet! Yay!

Now need to fins how enable SSH on it... Anyone got that successfully?

galvesribeiro

@jjeziorny / @obenturk How did you got to the UF-Instant terminal? I've built this tool https://github.com/Unifi-Tools/UFiber.Configurator that allow full configuration of UF-Loco and UF-Instant. I just received an UF-Instant and I'm looking to adapt the tool to allow the same changes on UF-Instant ...

galvesribeiro

I am from Brazil. you would have the firmware dump of this model to send me I don't have an EEPROM recorder with me... If there is a way to dump things from within SSH, I can send it to you. I've only updated the image1 with the `3FE47111BFHB32` firmware, made it boot from it and then have the SLID...

galvesribeiro

this link https://github.com/hwti/G-010S-A

Ah ok, the firmware repo. Got it, thanks!

I'm still trying to get it to work with Vivo here in São Paulo... I hope someone will see me question above and from the logs are able to tell me what else am I missing...

galvesribeiro

Hi, I'm new to the forum. I am looking to buy an SFP G-010S-A that is being sold by Aliexpress. '' Actually, I wanted to buy a CarlitoxxPro CPGOS03-0490 v2.0, but the price is very high for shipping to Brazil ''. Well I don't know if the G-010S-A will work with my ISP. I am from Brazil and I have a...

galvesribeiro

so I got a bit further. copy /proc/ubnthal to /var/config/ubnthal # mkdir /var/config/ubnthal # cp /proc/ubnthal/* /var/config/ubnthal edit the files in /var/config/ubnthal with the settings from your ONT then mount /proc/ubnthal with the new directory # mount --bind /var/config/ubnthal /proc/ubnth...

galvesribeiro

Hello folks! Today I have Ubiquiti UF-Loco and a TP-Link XZ000-G3 ONUs working on my ISP replacing their modem. Got a couple of the G-010S-A . I'm trying to make them work with a UDM-Pro with my ISP in Brazil ( Vivo - a Telefonica company) of which sends internet on VLan 10 . The ISP uses a Huawei O...

galvesribeiro

Hi, I'm new to the forum. I am looking to buy an SFP G-010S-A that is being sold by Aliexpress. '' Actually, I wanted to buy a CarlitoxxPro CPGOS03-0490 v2.0, but the price is very high for shipping to Brazil ''. Well I don't know if the G-010S-A will work with my ISP. I am from Brazil and I have a...

Search found 38 matches

Re: VRRP + MLAG

Re: VRRP + MLAG

Re: VRRP + MLAG

VRRP + MLAG

Re: After enabling hardware offloading, console and mgmt stops responding [SOLVED]

Re: L3 Switch disable Ethernet port

Re: L3 Switch disable Ethernet port

Re: L3 Switch disable Ethernet port

L3 Switch disable Ethernet port

Re: After enabling hardware offloading, console and mgmt stops responding [SOLVED]

[Feature Request] Data Center Bridge support

Re: MLAG not Work in RouterOS 7.1 Stable

Re: Unable to use M.2 SSD on CCR2216-1G-12XS-2XQ [SOLVED]

Re: Unable to use M.2 SSD on CCR2216-1G-12XS-2XQ [SOLVED]

Re: Unable to use M.2 SSD on CCR2216-1G-12XS-2XQ [SOLVED]

Re: Unable to use M.2 SSD on CCR2216-1G-12XS-2XQ [SOLVED]

Unable to use M.2 SSD on CCR2216-1G-12XS-2XQ [SOLVED]

Re: IKEv2 for macOS clients with multiple networks behind the tunnel

Re: CRL showing invalid

Re: Azure IPSEC tunel with BGP

Re: Amazon AWS VPN -- A Working Configuration Example and Bug

Re: RouterOS <> AWS VPN - Asymmetric Routing problem

Re: RouterOS <> AWS VPN - Asymmetric Routing problem

RouterOS <> AWS VPN - Asymmetric Routing problem

Re: Usage GPON module SFP in Spain

Re: Usage GPON module SFP in Spain

Re: Usage GPON module SFP in Spain

Re: Usage GPON module SFP in Spain

Re: Usage GPON module SFP in Spain

Re: Usage GPON module SFP in Spain

Re: Usage GPON module SFP in Spain

Re: Usage GPON module SFP in Spain

Re: Usage GPON module SFP in Spain

Re: Usage GPON module SFP in Spain

Re: Usage GPON module SFP in Spain

Re: Usage GPON module SFP in Spain

Re: Usage GPON module SFP in Spain

Re: Usage GPON module SFP in Spain