MikroTik

FWIW there have been issues with default capsman config in version 7.8. I remember it pretty well because I had 12 cAP AX coming with 7.8 off factory which I needed for capsman installation and there was no config !? So I had to immediately bring them to 7.10 (at that time beta or RC, don't recall a...

True but what's the rationale to limit to arm/arm64/Tile only ?

Partial config = unable to answer.
How are your interface lists defined and firewall rules using those interface lists ?

Show config.
The order of ports in bridge setup is (in my experience) irrelevant.

So you're saying that CAPsMAN can control AX devices even though the CAPsMAN host (hAP AC3) doesn't support 802.11ax and the controlled hAP AX will still operate as a WiFi6 device? If that's the case, does the band/channel configuration in CAPsMAN host require any tweaking? AX or AC is irrelevant h...

Well, true enough. Unless the router is behind CGNAT...

Why not ?
You only go out then towards a device with public IP (dynamic or static) but it will still work.
Same with Zerotier BTW when it's behind CGNAT.

Now you ask something different.

Ac3 can use wifiwave2 drivers already for a long time.
It can control ax devices acting as capsman controller.

Using 7.13 beta ac2 can also use wifiwave2 drivers.
Ac3 was already able to do so.
And then it's all the same driver. The same capsman. The same fast transition settings.

What needs to be elaborated ?

What's wrong using wireguard in the normal way ?
In essence, bth is the same.

If you REALLY want to change devices, AX Lite is the lowest budget alternative.
But 1 port less.

Using 7.13 beta, yes.

Interface list.
Move ether 1 from wan to lan.
And then move dhcp client from ether 1 to bridge.

Picture didn't show the blue plug, so I wasnt sure there...

I suspect one of the peers is not on a fixed IP but a dynamic IP (normal or CGNAT) ?
Set on that peer keep-alive time to 25s.
Then see what happens.

Already tried reset from Winbox/Webfig ? Can you try USB reset for that port ? On RB5009 there is an issue (I haven't checked if it is already resolved with latest 7.13beta) where after reset, USB port toggles between USB2 and USB3. Funny when having containers running on that USB device ... NOT ! T...

Guys (or Girls or Neutral or ...),
let's all keep it civil, shall we ?

2 last posts edited.

"Searched, and thou shalt find'

First hit
viewtopic.php?t=194768

That wasn't about ax lite ?

Really ?
Any references ?

Normis already told it in one of the very first threads on this device.
viewtopic.php?p=981211#p981211

Correct.
Use Quickset after starting from default, never after making manual modifications.
Or restart from default.

My wireguard connections are operational already for days...

It's ARM based so you can run zerotier on it.

And it does have wifi, in case you need it.
2.4GHz only but with a capable client you can reach 400Mbps.

Even more versatile, the LTE version.

It doesn't have a beeper, though

Are the added rules showing increase in counters ?
If not, they are not doing anything.

And then your issue is on another port or elsewhere.

What frequency is the AP using and are you 200% sure your device is able to use it ?

I recently upgraded 6 win7 installs to win10.

5 (FIVE) had to installed from scratch again because of issues.
Don't get me started... that was win95 stuff.

@Moba
Wireless repeater possibility always has been available.
Station bridge mode, where the same subnet can be extended, has been away for a while.
Not sure if it was 7.12, definitely in 7.13beta, I already tested it.
Check release notes.

Since I am by no means a network guru, most of your abbreviations are way over my head. I'd really appreciate if you could narrow down your recommendation to one or two concrete models that I should buy. Even for non-network guru's, surely one can search ? How else can you learn ? hap = Home Access...

Wi-Fi performance for the ax2 and ax3 is somewhere between 800-900 Mbps from user feedback. The lite will be a lot less, since it is only using 2.4 GHz. Still ... I can get 400Mbps with AX Lite. On 2.4GHz and when having a proper wifi6 client. e.g. my laptop only has wifi5, it doesn't get there. Us...

Winbox / Files

Also keep in mind Mikrotik makes sure to adhere more and more to wireless regulations which for most countries also means... reducing transmission power.

Hence my "theoretical" label.

It might be a lot easier to foresee 1 LTE capable device and use that as permanent backup on 1 fixed spot.

I upgraded my RB5009 last friday, also acting as capsman, incl AX2 and AX3. On that RB5009 are also some containers running (amongst them PiHole). I had zero problems with that upgrade. One exception: upgrade via capsman of the cap devices was not possible until I specified an upgrade path and the n...

Theoretically what you CAN do, is create a virtual wifi interface not connected to capsman and set that one in station mode. Even with old capsman or legacy wifi devices this is possible. PS don't throw away that cap ac ! With 7.13beta wifiwave2 is also available for quite a bit of ac-arm devices, i...

Connect via wifi.
But I see it has been discontinued ?

https://mikrotik.com/product/woobm

So is MQS ?

Moca I knew but g.hn is new for me. Interesting.... I'm not finding any real applications right away or I don't know where to look ... ? Is it still more in the theoretical sphere ? Edit Ah, it looks like Devolo and TP Link have some stuff using that standard. So it is basically powerline on steroid...

Possible, yes. Advisable, not that much (my view). Is there really no option to have a wire ? Even (... shivers... ) powerline can be an option ? If you still want to go wireless, keep in mind you may have to sacrifice one of the bands for backhaul connection. 2.4GHz or 5Ghz (I would choose 2.4Ghz, ...

If you did your tests pretty fast (within 10 minutes or so) it is possible the firewall connections still had the old situation remembered. That's what connection tracking partially is for, to avoid an existing connection needs to pass all "new" steps each and every time, but it can also w...

In WInbox, it should be visible in the section Files.
You can simply drag-n-drop it to your computer.

When you plug ISP modem in AX Lite ether 1, does that port get a public IP address as well ?

Can you provide export of AX Lite ?
terminal: export file=anynameyouwish
move file to PC, remove serial, public IP (if fixed), passwds.
Post edited config between [ code] quotes for easier readability.

Does the ISP modem work in normal ethernet mode or PPOE ?

Additional question then:
where does show-client-config appear which is mentioned in Help pages ?
I don't see it in winbox nor cli (7.13rc2)

Here is your problem

/ip dhcp-server
add address-pool=*1 interface=bridge lease-time=10m name=defconf

Check pool settings on dhcp server.
Pretty basic to check dhcp first when it's not giving out lease.

Start new thread with export of your config on hex and cap ax.

IP accounting has been replaced by kid control.
Don't let the name fool you, it can do quite a bit more then just babysit.

Simply config both ax lite as normal ap.

See here for more pointers
viewtopic.php?t=182373

If you really want to go overboard

consider setting up capsman.

Probably because of wifiwave2 package, yes.

You can always remove it again.
Reset to default so default firewall is back.
Then add wifiwave2 again and finalize config.

Or use
/system default-configuration print
to see what default config is and add the missing pieces.

1 bridge is enough.

See this excellent tutorial on setting up vlan
viewtopic.php?t=143620

When you go VLAN all-in (as in, no pvid 1 anymore), 2 small things you need to do on each AX cap:

- add vlan itf with pvid = mgmt and attach to bridge
- set discovery itf in caps to that VLAN itf

And then it will work.

Yes, exactly.

Don't use those menus.
Simple.

I would suspect an admin running a CHR as ppoe server to know where to look and where to stay away ?

Wireless is not being USED on CHR.
It is only there to provide hooks for capsman.
It is/was exactly the same on ROS6 when it became bundled.

Don't run bandwidth test on the devices under test.

And we still like to see the config of both devices.
Everything else is speculating and guessing.

RB5009 to RB5009 should be way higher then that, I would think ? From AX Lite to RB5009 using 1Gb ethernet I can reach close to 400-405 Mbps UDP. TCP was around 211Mbps. For TCP CPU was hitting 100% on AX Lite so that was a hard limit (RB was still doing "nothing" there :lol: ). For UDP I ...

95% of the setup is done in the same menus.
The only real difference is for local radio you assign config to radio and use local as manager.. For caps you use provisioning and use capsman as manager.

The rest is about the same.

1- Cap AX means capsman for wifiwave2 (or wifi since 7.13beta). In that version there is no capsman forwarding, it used to be in capsman for legacy wifi. HOWEVER ... if you use VLAN setup with complete different base vlan (= pvid <>1), most likely your caps device might not be able to detect capsman...

There are 2 versions of wap ac
Mipsbe and arm.
Only arm will work with new drivers.

Only one bridge is needed on controller. no need to overly complicate things and probably why it is not working. Also, we need to see FULL config for controller and cap (minus serial, minus wanip, minus passwds). Post between [ code] quotes for easier readability. Sorry to give some though love here...

Probably a firewall rule.
The last part of your test even says so ...

Export config (minus serial, wanip, passwds, ...)
Post beteween [ code] quotes for easier readability.

Side note:
even upgrading from windows7 to win10 you occasionally run into situations where it CAN NOT be done without loosing all programs or even data.
But that's accepted by everyone without a problem ?

If MS can not get it 100% waterproof, why should MT ?

But it could be the problem is originating from a too soon startup which causes the SIM PIN not to be set at which point watchdog might get stuck in a bootloop. So a reset of LTE interface some seconds after boot, might still be in order then. Or one will never get out of the loop. Again: I complete...

Make a support ticket with clear description of problem and supout.rif file.

MT staff is not reading all posts here (some pass by but not all).
This is a user forum.

Disconnect and check that PC offline !

Either a bot or some virusscanner trying to get in your router.
The fact it's trying to use several different user names, makes me think it's not up to any good.

If your carrier is giving you a CGNAT address (and most do), nothing you can do about it. What is the ultimate aim of getting your dynamic IP address. To get back in ? Doesn't work that way with most LTE carriers. You need to create a tunnel OUT first to a known location and via that way you can get...

Flash is flash. Flash used in pendrives should be more or less the same quality as flash used on MT devices. It's best to avoid lesser know brands, however. I've run some things on a Pi-3 for years using a flash drive. No issues whatsoever. Currently I run 3 containers on RB5009 using Sandisk flash ...

Yes, now the rb5009 doesn't need the qcom package you will have to upload it for the ax APs for auto upgrade to work via capsman Actually, you ALSO need to upload the base ROS package to that folder or those APs simply disappear from capsman once you got a folder specified. Even with "none&quo...

Upgraded RB5009 from 7.13b1. It appears upgrade of APs (AX2 and AX3) via capsman manager does not work anymore like it used to be. Select APs, hit "Upgrade" and nothing happens. Log file shows an interesting entry: 0xf7f0f460 manual upgrade request failed, no file (wifi-qcom-7.13rc2-arm64....

Not sure what you're trying to achieve with all those port_scanner rules ? Waste of time, if you ask me. Drop everything, simply add accept rules before that drop rule (don't forget winbox, webfig,... whatever you need for yourself. And use SAFE MODE or isolate a port, off bridge). No need to spend ...

1- no. ARM/ARM64 devices only. That point is quite clear. 2. It may, it may not. Depends if a path can be found using the parts still left operational :lol: But you can always host your own zerotier cloud controller ... 3. Yes and no. ONE part on that network needs to be zerotier-capable. From there...

Off topic: Is this a planned exciting move, or a not so glad eviction notice? Planned move to apartment. Our house was built for 5, the kids all left. So time to move into something smaller, easier to maintain, ... In reality the new place is as far as habitable floor space is concerned, the same as...

7.12.1 or older, no problem to add wifiwave2 package to CHR and use that one as capsman controller.
7.13 beta, capsman should be included already in base bundle. The whole wifiwave2 menu tree is from here labeled wifi.

I'll put it on a someday/maybe list ... moving places, still got large part of current house to be emptied.

Dear MT,

Can u check this issue please.
So many people using your hardware as enterprise things not just a home things

Thx

What are you doing with a beta version on enterprise environment then ??

What settings do you want me to show, happy to help!

In previous versions Winbox showed possibility for 20/40/80/160 as channel width on AX2 and AX3.
Seems it's not the case anymore from what I can see on some of my devices so that's a good thing, no confusion anymore.

Just a word of caution: 80+80 is not the same as 160. And if I'm not much mistaken, ax2 doesn't support any of these variants. Correct. That chipset, also used in AX3 and cAP AX, is unable to go to 160MHz channel width (or any underlying combinations). Why the settings you see in Winbox/webfig do s...

@holvoetn: I can just imagine you reading the following resolution thinking... I told you so.

I NEVER would do such a thing

Good thing you found it yourself.

@whatever: that's the one I use as well on my phone. On PC I use Wifi Analyzer https://matthafner.com/wifi-analyzer It appears that out-of-the-box my Mikrotik hAP ac3 doesn't have the wifiwave2 package installed. Out of the box it still comes with ROS6, I believe :lol: @holvoetn: If I install the wi...

I understand the confusion. Also because in R6 it was shown in Gb from CLI... Wiki pages (R6) show it with Gb. Help pages (R7) however are all in bytes. My advice: Divide the number 3 subsequent times by 1024, a bit of free mental training :) Or simple place mentally a decimal sign between 9th and 1...

Use simple queue ?

The hard but most effective method for cleaning = netinstall.
With reset some things may still be left.
With netinstall everything is completely gone, a real clean install.

I don't know what country you're in but for me, it shows this (AC3 device with wifiwave2 driver): [xyz@TP-Lint-AC3] > inter wifiwave2/radio reg-info country: Belgium number: 1 ranges: 2402-2482/20 5170-5250/23/indoor 5250-5330/23/indoor/dfs 5490-5710/30/dfs If your iPhone is transmitting above 5710,...

@normis: don't get me wrong ! I welcome what you guys did a lot, it really shows your company is willing to make the extra effort for your customer base. It will certainly help to boost sales on the still existing arm-AC devices now they can be reused/reconfigured and even expanded in numbers for ex...

Just some thoughts ... I have the impression with the release of 7.13beta and the wave2 ac-drivers, MT shot a bit in their own foot. On one side it will make sure current owners of wap AC have no real incentive anymore to move towards AX. Potential missed sales. On the other hand, since wAP AX is no...

Not if those non-Mikrotik devices ARE capable of using those higher frequency ranges.
Don't assume. Check.

Assumptions are the #1 reason for most failures.

To my knowledge: As it is now: You need (at least) one capsman controller using wifiwave2 and (at least) one separate controller using legacy wifi-package for controlling the respective access points through capsman. As far as I am aware you can not run both wifi-packages on the same capsman contro...

Are you sure the frequency used by iPhone when in hotspot mode is within range of AC3 5GHz band ?

...and at the same time kills radio signals, mr radio engineer

Already tested on ac2 and cap ac, it works just fine !

Leds in the back can be disabled.
Turn around the device then ?

All mikrotik routers can use DDNS (IP / Cloud).

My view as well.
Moving from V6 to 7.12, it might be better to netinstall to be sure all cobwebs in the dungeons are cleared.

Just noticed on AX2 ... all ethernet ports have POE tab ??

EDIT: my bad. Ether1 only and that's correct.

Look on this page:
https://help.mikrotik.com/docs/display/ ... geFirewall

Hello Time (and lots of other STP stuff) is a setting under Bridge Firewall, so it seems.

The CME Gateway is interesting — like the PoE IN & OUT — but what does the "CME" acronym stand for?

Educated guess ... Cat-M to Ethernet ?

You need a different MAC address for each end of each EOIP tunnel. If you use IP address, 1 IP for each device where you connect to. In your case: 2 tunnels = 4 ports = 4 MAC addresses. 3 devices being connected = 3 IP addresses. You need to look at EOIP as an ethernet cable. Every ether port has it...

If you can replicate this behavior, best to create support ticket with supout.rif included.

I removed my reply since it was ROS only.
You're looking for swos input.

Post moved to SWOS section.

I think that shouldn't be a problem.
Just don't use wifi and set LTE interface to passthrough mode (last part is how I think it should be done, never used it myself).

True but then you loose all user info (which you can keep at reset if you set the checkbox) but you will also loose all previous made wifi settings.
And you need to remember to switch OFF caps mode again before starting to configure wifi again.

There is more then 1 way to reach Rome

ROS 6.49.10 is a special case because it is AND stable AND long term. You can ignore that message (though it's not logical at all). If you want to upgrade to ROS7, you need to use upgrade channel (but not needed here). When you configure the device using wireless, it would be a bit normal to loose c...

Now THAT's a big bug !! Have you contacted support about this ? As a side note: in your first post you mentioned you were told to move it to SWOS. Who told you so ? Personal note: I also have a SWOS device in my home network (CSS610, SWOS-Lite) to learn what it is but I prefer ROS a lot more (much m...

This is quite possible. Quick version: - Connect using Winbox MAC on ether2 of cAP AX - move ether1 from WAN to LAN list (important for firewall and NAT) - move DHCP client from ether1 to bridge - remove DHCP server - add ether1 to bridge And that's it, I would think. You could also choose to comple...

I've done quite a bit of reboots already using Winbox 3.40 / System / Reboot ...

Not really seeing where the questions are ? Here are my thoughts. I am assuming you're going to setup everything locally (read: no capsman). In that case, literally the smallest you can get is mAP Lite (about as small as a matchbox !), eventually mAP so there is one more ethernet port if needed. 2.4...

First, to answer your question about RIP, as I've mention befoure , in my work place is an VPN server witch connect 22 locations witch are sharing their network classes between them using RIP, it was the easiest way in 6.49. You never mentioned before there were 22 sites connected to that VPN :lol:...

Yes but since you can not test it in a separate environment, I advise NOT to implement this in production with a beta version. These new drivers are too new, still some quirks to be ironed out and no real long-term feedback yet as far as stability is concerned (though the first responses I've seen h...

With the release of 7.13 BETA ( ! be careful if you want to use this in production environment ! ) cap AC and cap XL AC devices are able to use wifiwave2 drivers. Is it an option for you to set up a test environment using those wifiwave2 drivers as capsman ? You would also need a controller using th...

Wait what? wAP ac is mipsbe with AR9300, but the wifi-qcom-package works on it?
That's pretty cool!

Sorry to burst your bubble but this is about wAP AC arm version...
https://mikrotik.com/product/wap_ac

No experience with RIP. I could be wrong but I didn't see anything specifically being mentioned on that function not working anymore in release notes for ROS7 ? Maybe best to open new topic on that specific part. As a workaround, you can still setup the needed routes manually for now. Question from ...

Just setup L2TP.
It should work between 6.9 and 7.12

Find that hard to believe, wireguard was not possible on vers6 Yes, I have 2-3 port forward rules, and one VPN out, with RIP on it, and one VPN in wireguard to an interner Homeassistent server. Who says wireguard was setup on Tik ? It's WG in to internal HA server, so I understand ... Who's making ...

Actually not.
The way old capsman worked is quite similar how wifiwave2 is set up.
The commands shown in the web page can quite easily be found back in the gui part.

I'm going to let this one pass to show this is a CLEAR chatGPT response.
It DOESN'T know yet MT made wifiwave2 drivers available for AC devices... so much for the parrot response.

But the member posting it ... bye bye.

1- local radios are managed locally. Those can not be controlled by capsman but since they are running on the same device acting as capsman controller, radios will participate in roaming (provided you use the same config/ssid/...) 2- no, that's not normal. Where is your DHCP server ? I don't see it ...

The help page I linked to is a quite good start. Make sure in configuration FT tab to enable "FT enable" to yes and "FT over DS" to yes If you also plan to use radios of AX3, those need to be configured locally (don't set them to use capsman, only local). But since they will shar...

... but it does require, for now, 7.13 beta version.

If you have 2000 devices in the field, I would think you have some leverage to get this corrected through support channel ?

Which devices do you plan to use via capsman ?
If you only have that one ax3, set it up locally and done.

AX3 is a wifiwave2 device.
Capsman for wifiwave2 can be found under the wifiwave2 menu structure.

https://help.mikrotik.com/docs/pages/vi ... d=46759946

What does log say ?

Most likely not enough space to upgrade.

This one from Mikrotik helped me a lot setting up pcc between vdsl and lte.
But you need to hide the subtitles since some key info was hidden under them

https://youtu.be/nlb7XAv57tw?si=Jcst1QXGBJI-8Fp-

Using vlan, certainly so.

I suppose it should be PCC.
Per Connection Classifier.

Another thing to consider: If the devices communicating unexpectedly are on the same network segment without passing the router, it's normal they can talk to each other. The router didn't have a chance to block anything. A network diagram might help to clarify things (can be a simple drawing on pape...

We need to know a bit more on the context, a network diagram perhaps ? Simple drawing on paper can be enough. General advice: 1 bridge on your router, unless you have a real good reason to have multiple which for most, myself included, means if you do not exactly know why you want to split, keep it ...

Which is probably why nobody answered yet.
That and it's weekend...

Nope.
Only as of 7.13b this should be possible.

Towards old Wireless, it says.

Wireguard
L2TP/IPsec
Openvpn

Pick one.
Help pages from Mikrotik describe setups for each of them.

Personal favorite: wireguard. Outperforms all the others.

Best to create supout.rif and make a ticket to support with your findings.

and also station-bridge is not supported on wifiwave2

Actually, since 7.12 it is.
Already tested it.

*) wifiwave2 - added station-bridge interface mode;

And you may want to start to read this excellent reference material from member pcunite:
viewtopic.php?t=143620

(read it a couple of times, it will take some time to digest)

Proper reset sequence: The reset button has these functions: Hold this button during boot time until the user LED light starts flashing, and release the button to reset the RouterOS configuration. Keep holding the button for 5 more seconds or until the user LED turns off, then release it to make the...

To do what ?

Side comment: personally I would increase lease times on some of those DHCP parts. 10m is too short for most (and it will cause unnecessary writes to flash each time a new lease is handed out) Guest wifi could be relatively shorter (1h), rest I would put at 4h, even 1d. On your RB4011-config (I was ...

A couple of misinterpretations on CAP config: /interface bridge add admin-mac=*** auto-mac=no comment=defconf name=bridgeLocal /interface wifi datapath add bridge=bridgeLocal comment=defconf disabled=no name=capdp ====ADD === /interface vlan add interface=bridgeLocal name=VLAN99 vlan-id=99 /interfac...

No tag bridgelocal needed.
Cap also needs to listen to vlan99 interface.

Interface

Your port 10 is tagged vlan 99?
Then you need to add vlan 99 itf to bridge on cap.
Don't enable vlan filtering.
And set listen itf for cap to vlan99.
Then it should work.

In my setup: Router: normal VLAN setup (see for reference excellent guide from pcunite). Cap: added VLAN itf to bridge with pvid of mgmt vlan. Set cap to listen to this VLAN-itf for controller. And that was all. No VLAN filtering activated, no ports defined, nada. When you have a hybrid VLAN setup (...

Not really.
Never use webfig, only winbox ( direct or via Romon).

Why ranges ? Every time the AP changes frequency (because you allow it), you will loose connection. I always set my frequencies fixed (after planning and scanning of the environment, either manually, either through provisioning) Can you enable wireless debugging, it will show you more info on what's...

Configured an AX2 with your settings for local 5GHz on wifi1. Laptop connected to it using wifi5-card. It shows 802.11ac (in one of your last screenshots I saw 802.11n being mentioned ??) No issues. No disconnects (with connection to Azure Remote Desktop I would know immediately if it disconnects, e...

You only changed that frequency setting ?
I am going to load your config up on a spare AX2.

This is turning into a monologue ... I think I am going to close the door.

Fuzzy explanation ...

More info needed on the complete context of the setup.
What is located where ?
And what are you trying to do ?

Tip:
Check allowed addresses in peer settings.
Most likely your problem is there.

Probably because you only have a path for 0.0.0.0/0 to gateway of VDSL and Coax with each having their distance and no specific path towards your Coax gateway (or VDSL gateway). Just guessing since you did not provide any further info. Distance makes sure the first one which gets found for the same ...

Ok, then we change focus...
I see you use frequency ranges. What if you set a specific frequency ?

If you want to do routing between ports of different pvid, the bridge needs to know about each of them.
If not, it passes simply by since the bridge can not " read" the packets.

That's my probably too simplistic understanding.

Whenever you change firewall rules, clear conntrack table or reboot router.
Then you will see the new situation being applied.

Check help pages.

Don't believe me.
I have a working setup (multiple).

Watched the video, it's the one from Mikrotik ?
I stand corrected then.

But...
There is a section there which mentions provisioning.
You missed that part ?
Even for 1 cap you need to do that.

In your case, I advise using dynamic enabled

Yes, that's what I am referring to. CAP you set in caps mode and done. Nothing else to be done there (assuming it's AX device and everything is running wave2 drivers). Capsman, there you set the configs for the cap to be applied. If you use a device having own wireless interfaces as capsman, you nee...

Why use capsman if you set the interfaces manually ???

Definitely not default config. Focusing on the wifi part since that's the part giving you the most trouble. Where does this block come from ? Manual setting ? add channel.band=5ghz-ax .frequency=5500-5560 .skip-dfs-channels=10min-cac \ .width=20/40/80mhz configuration.country="United Kingdom&qu...

Post your config please.
controller and cap.

Up til now we never saw it.

And still we never saw that config ...

Maybe @holvoetn can sharw config, if im not wrong he have ax2 as CAP. At home I have capsman setup with RB5009, 1 AX2 and 1 AX3. I have a couple of AX2 standalone with a customer (running just nicely) and I also have capsman setup with RB5009, 11 cAP AX, 3 AX3 and 1 AX Lite. Also running as smooth ...

Post your config please.
controller and cap.

Up til now we never saw it.

Already launched a support ticket about it ?
What was the response ?

Why ?
The discussion on itself remains civil.
People can agree to disagree.

Thread locked.
Please continue in the other one

I never ran into a wall either.
I know it will hurt ... don't need to do that to know it.

Drop the youtube video (since clearly it's not working) and use this guide.

viewtopic.php?t=143620

TIp: most likely there are some firewall rules to be corrected.

Nearest possible solution would be hap AC2. Drawback: old wifi drivers. With 7.13beta channel it is possible however to load the wifiwave2 drivers on it but space is a problem on that device, not much left for other things then like e.g. zerotier. If you want to move to AX wifi, then it immediately ...

@mkx Believers will keep on believing. I have the impression someone is not willing to listen to reason because of tunnel vision. My personal view not affected by any AI tool ... Besides, if I ask ChatGPT itself, this is what I get. So who to believe??? :lol: Will chatgpt be able to write a perfect ...

Or it was a real quiet weekend ...

Native language Dutch (Belgium, northern part)
Fluent in English and French
Notions of German.

You're looking at the wrong page.
So you did not read the release notes for 7.13beta.

https://help.mikrotik.com/docs/display/ROS/WiFi

Yup

7.13beta

Which older devices can not use anyhow...

What IP address did your PC get ?
Could be it should be 192.168.88.1 for accessing the router (though user manual does mention 192.168.188.1).

If your APs are going to run wave2 drivers, obviously the controller will have to do so as well. And there I am not so sure it can be done on RB750r2 ... it is a rather limited device, resource wise. Processorwise it will be possible but I'm not sure about storage or RAM. You'll have to test. Again:...

Until 7.12, wifiwave was not supported on a lot of devices. With 7.13beta this had changed and your wap devices are supported, if I recall correctly. This requires replacing stock wireless package with new qcom-ac package. And then roaming will work. But... beta. So use at your own risk or wait for ...

Looks like the device already has been used ?

Factory reset.
If that doesn't work, netinstall.

What security settings do you have on 2ghz channel ?

Some old devices only want as low as WPA.

Netinstall

Unless i am mistaking
Subnet is L3.
Vlan is L2.

While not common, you CAN have multiple subnets in 1 VLAN.
Vlan is virtually a cable so l2.

My take: if you put IoT devices on their own vlan and they want to create havoc within that subnet, let them. They will not be able to get to the rest of your network (if properly firewalled). If needed, you can segregate further and put each device in its own VLAN (solitary confinement, poor things...

Ok Anav.
Eagerly awaiting your version then ...
Let's see if it is better.

FWIW the PCC youtube vid made by MT is quite good. https://www.youtube.com/watch?v=nlb7XAv57tw Used it again to clean up an AC3 LTE setup for PCC sharing across VDSL and LTE. Only, THIS time I disabled the subtitles which all of a sudden made me see a couple of important things I missed the previous...

VLAN combined with proper firewall rules, yes.

Caveat
One of your requirements is about isolation of wireless clients.
What APs are in use and what control do you have there ?
Because if the acces point can not block it, no way you can prevent it from happening.

I think you may have to start to study this excellent guide on setting up VLANs. A lot of stuff will become more clear then on how to proceed. https://forum.mikrotik.com/viewtopic.php?t=143620 (read, let it sink in, reread again, digest it more, test setup, read again) High level I don't see immedia...

So you're trying to add cAP XL ac to capsman controller running on AC2.
Correct ?

AC2 is running which version ? And which packages on it ?
cAP XL ac is running which version ? And which packages on it ?

Winbox has nothing to do with memory leak on my test RB951 running 7.13Beta2 (since Winbox was not in use). Here you see memory usage last 2 days. Stange it increments in the same amount, but not at a fixed time. Span on every sample is 5 min, . memory.png Must be something new for 7.13b2/3 ?? My R...

When cable is not connected, interface will not work.

As soon as it is connected, the DHCP client will make sure to get an IP address from the router upstream.
And it should then also provide a route and DNS settings for internet access to work.

i.e. To me it was not clear that after the upgrade and the installation off the qcom-ac package I have to reconfigure my wifi and under which menu tab I had to do that. Personal comment: when you add wifiwave2 package to AC3 (pre-7.13 chain), you would have to do the exact same thing. Old wireless ...

Can't say I'm seeing this.
I have 1 AC2 installed since 14/11 with 7.13b1 (because I was really eager to test the new wifi package), hasn't been reboot since.

Supout and support, I would say...

Without further information on context and setup, the answer is going to be rather generic too.

Use MAC address and static DHCP lease to hand out IP address to the relevant device ?

Cap ac to cap ac, it is possible but you still would need to correct MAC addresses etc...

If you have multiple, why not use capsman so the caps device can be simply reset to caps mode and you're done ?
That's the whole idea of capsman.

Simple AP config with external router. Connect to device using winbox MAC address remove dhcp server from bridge remove dhcp client from ether1 add ether 1 to bridge add static ip address to bridge add route 0.0.0.0/0 to your router add DNS settings (typically that would be your router) That should ...

hAP AX2 7.13_Beta2 When I add channel to the WiFi menu with show coloums channel dissapears when I reopen the WiFi tab as follows below, also there are two instances in the show colums box. I think this might be a winbox thing. I'm seeing it as well on a brand new AX2, still running 7.8. (although ...

Why not ?
A reported bug is a reported bug. Doesn't matter where it comes from.

Not realy sure if i became stupid or i don't understand something.

... What am i doing wrong?

If i upload old Wireless package back again, it installs normaly and i can see my Wifi interfaces.

Probably not enough space for the new wifi package ?

Export config
Netinstall
Import config

As indicated in other thread, use correct country settings.

Yes, that's a consequence from Mikrotik observing quite strictly country settings (as everyone should but some manufacturers are quite a bit less obeying).

And if you set country correctly as it should be ?

DFS detection, perhaps ?
Normally it should move to another frequency on its own.
(but maybe it got confused because it thinks it is in Canada

)

Can you downgrade to 7.13b1 to test again with auto ?

Q: why do you use Canadian country settings when you are based in Kiev ?

Added: you left 5GHz channel selection to auto.
What if you do specify a frequency (pick one preferably not in DFS range) ?

Can you also provide on AX2 output for
/interface wifiwave2 radio reg-info country=Canada number=0

I have the exact same setup at home which I use for testing as well before moving to production devices on my clients network. For now still on 7.13b1, everything working smooth using VLANs and everything. Is something mentioned in log file of AX2 ? I ask because I saw someone mentioning a problem w...

SAFE MODE will be your friend when testing/configuring.
https://help.mikrotik.com/docs/display/ ... %2B%5BD%5D.

1- can you make a drawing how everything is connected because it's not clear to me ... 2- Since you changed base vlan (pvid=1) for that cap AX (I think ? Hence my question for a more clear picture), on cap ax you need to add VLAN133 interface as part of bridge. Don't enable VLAN filtering. Set DHCP ...

On router Chateau 5g will i be able to use the new wifi and zerotier at the same time? I am using it at home and purchased as "future proof". Am I facing a replacement? Alternatively to what model? A device with 16Mb of flash does not really fit my definition of future proof ... FWIW I fa...

Search found 4737 matches