Thank you

Sounds not good, need shaping each user in list 512k, not share 512k to all users, how to make it correct? Or I dont understand you? Sorry for my english

Put those addresses on an address list (summarizing where you can for fast processing). Apply a packet mark for all traffic to/from addresses on that address list. Install a queue for that packet mark. Simple example using simple queues: /ip firewall address-list # the below is a summary of .30 - ....

My results:
800m link
x86 775 Celeron 1600mhz
r52n
dual polarity 31dB parabolic
4m LMR-400 pigtails
mpls bridge
In future will try to upgrade 12km 802.11a nstreme turbo link )

the signal is -50 -52. after fixing rates on load ccq much better. But nstreme doesnt working for me. Ccq 20, bw 1-2 mbits with nstreme. Without nstreme bw much better. But latency with r52 5ghz nstreme was better.

I can provide access to such link. My email andevariel@gmail.com, ICQ 207-100-964. Remote access already configured. Thank you in advice.

Hello, I have a problem with the "n" link. ROS 4.4. Distance 800m, 2 separate antennas 26dbi in different polarization. r52n. 5Ghz. Tried different freq. CCQ in both directions after installation around 98-100%. But on-loading TX CCQ from bridge and RX CCQ from station near 20-25% ( Im usi...

Hello,
1 antenna V, 2 antenna V <=> 1 antenna V, 2 antenna V
or
1 antenna V, 2 antenna H <=> 1 antenna V, 2 antenna H
better for "n"?

Hello, I have a router with ROS 3.13. Motherboard Intel DG31PR with integrated Realtek* RTL8111-GR Gigabit Ethernet Controller. Router hangs up ( It is enough to turn off/ turn on Ethernet (100Mb) to recover router. Thus router rebuts. If to connect router to gigabit switch router doesn’t hangs up. ...

Is it possible to downgrade to ROS 3.13 x86 from 3.16 x86? Cannot do this with winbox. If it possible, please help howto ) thy.

There is radio bridge configured as http://wiki.mikrotik.com/wiki/Transparently_Bridge_two_Networks MT1 <-> MT2. After MT1 - our router (FreeBSD). After MT2 - router of ISP. FreeBSD Router <-> MT1 <-> MT2 <-> ISP router I need to prioritize trafic going throught radio bridge MT1 <-> MT2. p2p - low h...

Yes, trouble was with ethernet card. Reconnected Mikrotik to gigabit switch, in gigabit mode adapter works properly wtf _).

Is D-link Gigabit Ethernet PCI Express DGE-560T compatible with RouterOS 3.1?
Thank you in advice

hello, I have a great trouble with MT, sometimes i cannot get any request from MT, no winbox, no telnet or ping. mb is Intel® Desktop Board DG31PR, ethernet is onboard Realtek* RTL8111-GR Gigabit Ethernet Controller?, but Mikrotik says (in driver list) RTL8169 Gigabit Ethernet. When i unplug and plu...

ty,
ip is 192.168.88.1 )

Any default ip address present on ether1 after setup r y? RouterOS 3.1.
ty

Try to check 3.0rc6 version,
http://www.mikrotik.com/download.html
Report back with the results.

ty, working with 3.0rc6 )

How to make Mikrotik working with RTL8101E/8111B Ethernet LAN (motherboard Intel® Desktop Board DG31PR)? Or it is not possible? I had installed Mikrotik over the network with floppy but when I type in console "interface print" I see only WLAN iface (((