MikroTik

Ca6ko

The bluetooth in the Mikrotik is for the IoT. And all the control is located there. Therefore, it is possible that the corresponding package is required for operation.

Ca6ko

Update the device via the test branch to 7.12.1, then update the Stable branch to 7.14.1.
NetMetal AC² is an old device.
The new device is a NetBox 5 ax

Ca6ko

I have not.

Ca6ko

supports the IEEE 802.3af/802.3at PoE standard and operates with a power supply of DC 12V/1.5A.

Correct not and, but or.
Your device is powered by a 12V power supply or 802.3af/802.3at 48V .

Ca6ko

Have you tried forcing the POE on?

Ca6ko

1200 Mbits/s and 574 Mbits/s these streams can pass only on wifi ports of pure data there is half of it, so 1774 can not get to ethernet port. CAP AX judging by the specification can not power CRS326-24G-2S+ it does not have enough power even if you use a power supply at 30V, the maximum you can sup...

Ca6ko

Yes, there are new AC and AX standard devices.
But antennas have always been Mikrotik's weak link. So a separate antenna will always be the best option. I would recommend the NetBox 5 ax

Ca6ko

Then, I've changed mode to station pseudobridge and hAP AC was able to connect to hAP AX3.

pseudobridge support only appeared in 7.14

Ca6ko

There are more ways to assign frequencies:

You give the format of the terminal command, and the topikstarter uses winbox.
I have not been able to replicate his entry.

Ca6ko

Add ft=yes ft-over-ds=yes to the /interface wifi security this will shorten the switching time.
Enable 5 GHz.
On wifi only the client decides where and when to switch, if the client decides that the connection quality on 2.4 with your SSID is bad he switches. The 2.4 band is probably overloaded.

Ca6ko

However, in addition to channel 5660, it has 5220 as a secondary NO DFS channel.

You did not set the second frequency correctly

Ca6ko

Try manually setting the speed of the SFP port

Ca6ko

Or set up a super channel

Screenshot_16.jpg

Or use the terminal command

/interface wireless
set [ find default-name=wlan1 ]  antenna-gain=0

PS Usually reflashing via net install removes the region lock and the superchannel appears

Ca6ko

Try setting the antenna gain parameter to 0

Ca6ko

On older versions of devices, and perhaps it was related to ROS 6. SoftwareID is linked to the serial number of the device and to the serial number of the memory chip. When the memory chip was replaced, the SoftwareID was different and the license key stopped working. PS It turns out that in AX2 boo...

Ca6ko

Beautiful work!
Are you saying that after replacing the memory chip you didn't lose your license and you didn't have to modify the bootloader to install the new amount of memory?
Were you able to start the USB socket?

Ca6ko

With the wifi-qcom-ac device using 'ap' mode and the wireless device using 'station-bridge' mode, no connection is established. When communicating between old and new drivers, you should use the same settings as for devices from other vendors. That is, use the station-pseudobridge mode. In 7.14 thi...

Ca6ko

I get that but I think as of 7.13 that’s not the case anymore… No everything is still like this and no changes are expected. Old drivers and wifi-qcom are still not compatible. In 7.14, the AX drivers learned how to station-pseudobridge Some help on how to use it with a bridge? There is still one c...

Ca6ko

I have 1000 square meter space with 4 cAP ax (one in each corner). In my opinion 4 points for such an area is not enough. I have an object where, for example, 450 square meters, two floors, 5 points are not enough. Did you do a radio survey? Did you calculate the placement of points, frequency plan...

Ca6ko

I found a bug please users to confirm. Devices with WiFi Mikrotik on IPQ -4018/19. If you select Data Rates configured uncheck all the boxes with A/G as well as all modulations HT MCS leaving only VHT MCS, the devices stop measuring the signal strength. Screenshot_4.jpg Screenshot_5.jpg Screenshot_9...

Ca6ko

That's the other solution @holvoetn was telling you
On map lite exclude wlan interface from bridge, make EOIP interface between map lite and any other Mikrotik device on the network, add EOIP to bridge on both ends.

Ca6ko

I understand correctly that you have configured 2 old Capsman one on CHR the other on mAP lite. PS. After resetting to CAP mode, the second capsman was deleted In this case on CAP ax manager search is enabled on the interface and not by IP address? (When interface search is enabled, IP search does ...

Ca6ko

Could you explain how SXTsq would help here?

The SXTsq Lite2 device is installed separately in the switch port, and only the mAP Lite is connected to it via wifi. It has a level 3 license so other devices will not be able to connect to this bridge. Authorization is at your discretion

Ca6ko

The easiest and fastest way is to buy a SXTsq device and set up a separate WiFi bridge.

Ca6ko

What makes you think that a radio channel has the same properties as a cable? Packet loss on the radio is a normal mode of operation. After all, you are using a common transmission medium and judging by CCQ you are not the only one using it.

Ca6ko

It's a strange situation with the United Kingdom. You can select such country in the wifi settings, but you cannot see what restrictions for this country.
Both in the old version of the driver and in the new one. Please contact technical support

Ca6ko

I posted, I've tried with a x86 router (a R86S mini system) and the results were the same.

Try limiting the 2Gbit ISP to 1Gbit and see how it works. It seems to me that there is a bottle neck for 2Gbit in your network design after all

Ca6ko

what is the output power and sensitivity , tthere is no mention in the specifications.

You just couldn't find them, it's a Mikrotik.

Ca6ko

Ca6ko

Is your router capable of pumping more than 2Gbps?

Ca6ko

be honest I was not able to find the "CAPsMAN" button in winbox

Screenshot_5.jpg

There she is

Ca6ko

But do you get a radome cover for LHG XL?

https://www.lasershield.com.br/MLB-1522 ... shield-_JM

Ca6ko

3 days is a very short time for microtik, usually you need 2 weeks to understand its peculiarities. You're trying to use your cisco experience and it's all wrong here, this experience is getting in the way. Let's start with the basics, the quick settings tab is one-size-fits-all. You can enter it on...

Ca6ko

If you add a route to 0.0.0.0.0/0 with a longer distance to each router, you will get more Internet channel reservation.

/ip route
add disabled=no dst-address=0.0.0.0/0 gateway=192.168.10.2 distance=10 routing-table=main suppress-hw-offload=no

Ca6ko

You can try to push stations to the other by using ACLs. I don't mean the Access List on the Access Point, I mean the of Connect List on the Station. With the help of Connect List you can set the order of Access Points to which the Station is connected. With the parameter Allow Signal Out Of Range ...

Ca6ko

I want a stupid hard to ignore status indicator for the office.

Turn on an optional audible alert, the louder the harder it is to ignore.

Ca6ko

you won't be able to control stations about which AP they'll connect

Why, if you use a Connect List, you can distinguish access points by MAC.

Ca6ko

For bridge-type connections, it is better to use devices specially designed for this purpose.
Devices with directional antennas.
For example SXTsq 5 ac

Ca6ko

In such a case, set the safety interval to long. The SGI abbreviation will disappear in the connection speed. Check whether the CCQ should increase under load. The rest, I think, should be left as it is. There is a "Safe mode" button to avoid losing access. It should be pressed before you ...

Ca6ko

You still haven't specified the wattage at which your points operate. According to the RBDynaDishG-5HacDr3 specification for maximum speed the power should not exceed 22dBm Screenshot_1.jpg Screenshot_4.jpg I think it was mentioned somewhere that the old ROS driver has a 280Mbit limit. These are the...

Ca6ko

You did not specify the main parameter of the radiolink signal strength. Let's go over the basic settings first Show the TX/RX signal for each chane Show the power that is set. You are operating in the frequency range of 5450-5530 MHz. Are you sure there are no interfering stations in it? First reco...

Ca6ko

As long as it's like this

https://cults3d.com/en/3d-model/gadget/ ... wall-mount
https://www.printables.com/model/549993 ... wall-mount
https://www.printables.com/model/542610 ... te-tc-case

Ca6ko

Why repair it right away, maybe it's not that bad? How does the device behave after powering on? Looks like you made the mistake of many beginners, after resetting the device can boot for several minutes, if you turn off the power at this point we get a brick. In this case helps netinstall. In Ukrai...

Ca6ko

Well, you didn't want to open a separate topic, so we'll continue here. Let's look at the only link that doesn't work for me. This link of 10 (ten) km. The signal was around -80 dBm on both sides and the throughput at 10 mHz bandwidth You said that only one radio link is not working. But in your las...

Ca6ko

No way.
Or write your driver.

Ca6ko

Screenshot_29.jpg

Then the system reboots

Ca6ko

Is there no change in the logs now? Show me.
To downgrade to 7.12, you must first remove the Wireless package and only then downgrade.
If you have wifi access, you can't do that. If you access the device via cable, you don't have to press the button to netinstall.

Ca6ko

@frengo It's certainly good that you posted your paraphrase of the netinstall instructions, but that's not what we're interested in. Did downgrading the ROS version to 6 fix the authentication problem or not? PS I wasted the whole afternoon trying to get down from 7.13 but there was no way, not even...

Ca6ko

Of course you do.
Tool/Netwach ping to the device, if there is no ping turn on wifi interface, if there is ping turn off wifi interface.

Ca6ko

I'm not a psychic. Tell me in detail how you do the downgrade. In general, search here on the forum many times written in detail how to downgrade the firmware version. Since 7.13 changes the configuration of the radio. I would recommend to use the Backup that you made before upgrading to 7.13 or bet...

Ca6ko

Obviously both Main and extra, right?

I haven't seen your configuration so I can't say. You should only install the extra package if you use it, and then only the necessary packages.
PS Usually one main package is enough

Ca6ko

Ca6ko

First impression is working better in test have better speed, TX and RX rate are more stable.

How much better, the numbers

before update has been around -50 now is -74. Check power it is the maximum like before.

New parameter antenna-gain set to 0

Ca6ko

What could it be? There are approximately 256 reasons. Open a new topic. The -80 signal is very weak. We'll figure out what's going on. Show me 1. The settings of each point 2. Scanning the air from each point. PS The first thing I suggest on this unit is to downgrade the ROS version to 6.49.10 Lon...

Ca6ko

I still haven't understood what makes them resistant to these attacks.... WPA3, ac2, 802.11w, MFP, Wifi5 class? Screenshot_27.jpg Based on your description, I can draw 3 conclusions 1. You have low qualification as a radio engineer. You have a very poor understanding of the settings of the radio li...

Ca6ko

What equipment should I use instead of mine? To give you actionable advice, you have not provided any information about the radiolink. You have purchased devices with 3 channels. Does that mean you have special antennas for them with 3 polarizations? If you don't look into the situation and answer ...

Ca6ko

It should be near to 700-800mbps. That's not a correct statement The teorical speed 833mbps for 80mhz bw at 5Ghz. This is not a correct statement. You are mistaken in terms and definitions. 833 is not a theoretical speed, but a channel speed. In this case, the data rate is usually 1/2. 420mbps is t...

Ca6ko

wifi2 - 5 Ghz (with Dynamic Frequency Selection)

Since the frequency selection is auto worth, there is probably a DFS check going on, which takes 10 min. Open the interface and see its status in the bottom line.

Ca6ko

What's with the search?
https://wiki.mikrotik.com/wiki/Manual:R ... et_buttons

Ca6ko

[system health get value-name=value [find type=V]]
Try this.

Ca6ko

You can't do this.
No option in the starlink router to do this.

In the old version of the application it was possible, I changed it for myself. Now there is no such item in the network settings menu. I apologize.

Ca6ko

Please don't be confused by the terms CAPsMAN v2 is working starting from RouterOS v6.22rc7. CAPsMAN v1 is discontinued starting from 6.37. https://wiki.mikrotik.com/wiki/Manual:CAPsMAN WifiWave2 CAPsMAN https://help.mikrotik.com/docs/pages/vi ... ve2CAPsMAN You need to configure the Capsman v2 to C...

Ca6ko

https://www.youtube.com/watch?v=JSoModWAPIw
https://www.youtube.com/watch?v=7MNdlO_msPY

Ca6ko

Please don't be confused by the terms CAPsMAN v2 is working starting from RouterOS v6.22rc7. CAPsMAN v1 is discontinued starting from 6.37. https://wiki.mikrotik.com/wiki/Manual:CAPsMAN WifiWave2 CAPsMAN https://help.mikrotik.com/docs/pages/viewpage.action?pageId=46759946#WifiWave2(7.12andolder)-Wif...

Ca6ko

Read the Chinese advertising information correctly. USB 1A 12V means 5*1=5W

Ca6ko

Turns out there's a lot of new products coming from Mikrotik.

Ca6ko

Dreaming about device ...5HaxD6axD

Why dream so faintly?
7HbeQ, 7HbeO

Ca6ko

Without nstreme or nv2 support this is unuseable for outdoor WISP operation.

Why.
There will never be these protocols in Wifi 6.
Wifi 5 wave 2 is already superior to nv2 in some respects.

Ca6ko

I can get to one of them by adding the appropriate route to 192.168.1.1/32 gateway eth1 or eth2 and enabling one or the other, but I would like to be able to access both. You need to connect to Starlink and change the internal network addressing. Instead of 192.168.1.1 set something like 192.168.23...

Ca6ko

Theoretically, according to the standard, wave 1 and wave 2 differ only in the distribution of airtime between clients, so when there is only one client there should be no difference. But the difference between wave1 and wave2 microtic driver gives a small speed increase.

Ca6ko

Hap ac2 got a cyclic reboot after upgrading from 7.12 to 7.13. The device boots up and after 30-40 sec goes into reboot. Supout file does not allow downloading the reboot occurs before downloading. I have not found anything in the logs. At the moment of availability I reset the config. After manual ...

Ca6ko

/ip address add address=10.0.0.1/24 interface=ether11-LAN network=10.0.0.0 add address=10.0.0.95/24 interface=ether10-INT network=10.0.0.0 You need to either bridge the LAN ports ether11-LAN, ether10-INT and set one address per bridge, or split them into different networks 10.0.0.1/25, 10.0.0.128/2...

Ca6ko

with WPA auth.

Do these devices support this ancient standard?
Reset the Mikrotik to factory settings, merge the ports into bridge and do not touch anything else.

Ca6ko

You'll have to figure it out for yourself. Because you have already configured multiwan on the router, it depends on these settings how you need to configure it. Otherwise my advice can break the whole work of the config. So look on the forum threads about multiwan there these settings are considere...

Ca6ko

Then you need to configure multiwan that the local traffic of the router itself goes to the wan port from which the request came.

Ca6ko

If an EOIP tunnel is established and it is bridge enabled, then no IP addresses are used between LAN1 hosts, they are in the same broadcast domain and frames go to MAC addresses. So you have an error in the scheme. For simplicity of understanding EOIP is a cable that connects LAN1 bridges into one n...

Ca6ko

Maybe we should move the existing access point 5 feet?
The optimal location of the access point and router are usually not the same.
PS
Sometimes you can get results by moving the AP within 10 cm.
https://www.youtube.com/watch?v=aqqEYz38ens

Ca6ko

But that is only one of 5 devices that are all apparently being offered DHCP leases when no client appears to be configured.

Show the config

Ca6ko

Why are you starting a new topic? https://forum.mikrotik.com/viewtopic.php?p=1040406#p1040406 Again, you do not provide any data that we can help you with. 1. Show measurements of the signal level at different frequencies 2. Show the settings of both points 3. Show what power is set 4. Show a photo ...

Ca6ko

Some IoT devices also memorize the MAC of the access point. When you change access points, you must either use the MAC of the previous access point or re-bind the devices.

Ca6ko

/interface wireless channels add band=2ghz-onlyn frequency=2412 list="2.4" name=ch1 width=20 add band=2ghz-onlyn frequency=2417 list="2.4" name=ch2 width=20 add band=2ghz-onlyn frequency=2437 list="2.4" name=ch6 width=20 add band=2ghz-onlyn frequency=2442 list="2....

Ca6ko

please someone should help me figure this out...i need to close out on this configurations please its very urgent Usually this is because the client and access point's WIFI parameters do not match. Unfortunately my IT tambourine is on an upgrade, and without it I can't determine what they don't mat...

Ca6ko

Is it meaningful to use CAPsMAN to manage APs (2.4 and 5) on the same and only device? That's what I usually do. In the logs I see that the connects to 5, then get's roamed to 2.4 then disconnects, that repeats a few times and then it gives up and picks LTE : It's a peculiarity of WiFi that the cli...

Ca6ko

According to the rb912uag-5hpnd product page it does not support 5060MHz as a valid frequency.

Ca6ko

No. It took longer for AX, because ...

The transition to AX is still underway, no wAP AX, Audience AX devices yet. Also there are no point to point AX devices yet.
Taking into account that Mikrotik certified in FCC 4 devices in 2022 and 5 in 2023, wifi7 devices will have to wait for a long time.

Ca6ko

You've encountered the ultimate traffic generator opportunity.
Do not run the traffic generator on the device under test, the measurements will be erroneous.
You can estimate the maximum traffic generation capability of the device by running a TCP test to 127.0.0.1

Ca6ko

Black electrical tape 1-2 layers

Ca6ko

Quick version:
1. Connect using Winbox MAC on ether2 of cAP AX

I prefer a slightly different way
2. System/Reset Configuration check Caps Mode and reset the configuration. The result will be the same.

Ca6ko

That didnt work. What didn't work? Did you build a profile of the radio path and make sure the first Fresnel zone was clear? replaced all hardware, still the same. No one advised you to change the equipment. any suggestions? What advice do you expect from the forum members if you don't give any inf...

Ca6ko

You have a second tunnel and a third node in your schematic. It can also have an impact. The choice of EOIP to build a single local network with one broadcast domain is not clear initially, but the networks have different addressing and different broadcast domains. It is more correct, in this case, ...

Ca6ko

LEDs of three colors green blue red are found in microtik devices. I propose to install RGB LEDs in new devices. And set color control in ROS. Then you can easily and clearly label and group the ports. For example, if you set blue color for WAN port and yellow color for bridge ports, you can immedia...

Ca6ko

You're not asking the right question so you won't get an answer. Power consumption as you put it "in standby mode" is a variable that depends on many factors. For example, it depends on the number of connected ports, it depends on the number and signal strength of registered wifi clients. ...

Ca6ko

what should i have to do?

Describe the problem in as much detail as possible and display a schematic. Personally, with my poor English, I didn't understand anything.

Ca6ko

- I believe @DanMos79 is asking for an alternative DIY wireless card compatible with WifiWave2 drivers for RB4011, if available in the market. Does new wireless drivers suport QCA9556?(wap ac)? qrt-ac with 128mb... The wifi-qcom-ac-7.13beta1-arm.npk package contains drivers for IPQ4019 and QCA9984 ...

Ca6ko

You're not even showing the tip of the iceberg. Judging by what you are showing to find the causes, you have very little idea of how wifi works. You must be a network engineer. (the network cable has nothing to do with the signal received). I can tell you from the bits and pieces you've shown me. 1....

Ca6ko

You didn't show what kind of sills you installed. It will be triggered when any threshold is reached. If you claim to have observed an average ping of 600ms, you can set such thresholds. Screenshot_31.jpg Then the main indicator will be 85% packet loss. If false alarms continue, increase the thresho...

Ca6ko

I have added the wifiwave2 package to my RB3011, and lost all of my configurations in the process, so I recreated those...

Are you by any chance trying to connect the incompatible old Capsman and new Wifiwave2 Capsman ?

Ca6ko

You have not provided any information to help you.
There are over 32 reasons, no one wants to guess.
1. The reason is elementary wind oscillation of the mast ...

Ca6ko

This is a peculiarity of Mikrotik, the parameter doesn't seem to exist, but in fact it does. https://help.mikrotik.com/docs/display/ROS/Netwatch In fact, the default settings are as follows Screenshot_27.jpg Triggering is not based on the number of lost packets, but on Thr Avg. Run a long ping and s...

Ca6ko

Ok I found the component on Aliexpress for less than 2,50 euro... 100 pieces... It will take its time to arrive, as soon as I'll get it I'll do my test :) You can short-circuit the inductance to do a test. The Schottky diode must be broken and something else in the red circled area. In general, do ...

Ca6ko

Apparently, you already have one L2TP tunnel to the RRAS server via Mikrotik, and Windows won't give you a second tunnel. Search on the topic 2 L2TP via NAT

Ca6ko

In general, I did not understand why IPsec connection was not established. I deployed tunnels from the center to the sub-offices and left it like this

Ca6ko

Help to understand strange behavior of L2TP+IPsec VPN Help me figure this out. Maybe someone has encountered something like this three routers in the network of one provider. public IP addresses with mask /24. One M1 server L2TP two other M2, M3 clients. Between them are configured tunnels L2TP+IPse...

Ca6ko

Mikrotik routers with S+ ports

Screenshot_3.jpg

Switches Mikrotik with S+ ports

Screenshot_5.jpg

Ca6ko

Try the command first.
/interface/wifiwave2/set master-interface wifi1
then
/interface/wifiwave2/set [ find default-name=wifi2 ] mac-address=78:9A:18:06:42:56
Doesn't help contact tech support.

Ca6ko

You can try a crutch.
Connect the hub as just a station and establish an EOIP tunnel by adding its bridges to both devices

Ca6ko

Your Radio MAC is set to 00 so the default script does not work. It looks like a hardware problem, please contact technical support. The error message says that you cannot set the universal MAC 00 must be set individually. The interface MAC and radio MAC are the same from the factory. Try to set MAC...

Ca6ko

Where did I misconfigure? "A chain is only as strong as its weakest link." You haven't calculated the budget of the POE. The standard RG45 port is designed for a maximum current of 1A. That is, when powered through the first port, the hex can consume a maximum of 24W when powered from 24V...

Ca6ko

What type of connector is in the picture? This is not a connector, it is a switch MS-156C, used in manufacturing to connect instruments to adjust the device. https://www.hirose.com/product/series/MS-156C# There is an adapter for the SMA https://www.hirose.com/en/product/p/CL0358-0188-8-00 The very ...

Ca6ko

The problem lies in the mutual influence of modules on each other. It can be checked quite easily 1. Run a throughput test through one module and without stopping it run a second test through the second module and observe a decrease in throughput through the first module. 2. Start scanning the airwa...

Ca6ko

Apparently they can't solve the problem with heat dissipation in a closed case. The ax2 has a lot of holes in the case. Since they haven't submitted for certification yet, it probably won't appear until the end of the year.

Ca6ko

Your question, paraphrased, sounds like this. "I need to move cargo, what kind of transportation do you recommend?" You're turning the problem upside down. First you need to determine the parameters of the link, and then select the equipment under these parameters. You can use the ubiquity...

Ca6ko

but the issue still happen

Downgrade the version until the problem goes away

Ca6ko

Wireless : Atheros MiniPCI Wireless 802.11a+b+g 54Mbps 2.4/5GHz It's even worse than I thought wifi3 would be in the days of wifi6. Your links have a single spatial stream. Let me explain a little more. From Main AP1 and AP2 you take out the modules that work on the link with AP18. Do the same in A...

Ca6ko

downgrade 7.8

Ca6ko

Category 6 cables? If yes, try changing to cat5

Ca6ko

I would recommend abandoning the scheme when one device (AP) serves multiple links. Since in such a case it is very difficult to get rid of their mutual influence. Go to the scheme of one device one link. Then they can be physically separated on some distance than to reduce their mutual influence. A...

Ca6ko

- RB922UAGS-5HPacD-US (USA) is factory locked for 5170-5250MHz and 5725-5835MHz frequencies. This lock can not be removed.

- RB922UAGS-5HPacD (International) supports 5150MHz-5875MHz range (Specific frequency range can be limited by country regulations).

Ca6ko

I haven't worked with ubiquity controller, but from what I've heard they have slightly different logic compared to capsman. Ubiquity controller is used only for downloading settings and then the point can work without it In capsman wifi interface is passed under the control of the controller. The co...

Ca6ko

but out of pure curiosity why there is only Home AP Dual? The quikset menu shows the modes in which this device can be used. Since WifiWave2 CAPsMAN is not supported by older devices, so that users are not confused, there is no CAP item. PS If you want to use old and new devices you will have to us...

Ca6ko

For what reason do you have an additional route created to the network address on the bridge? Screenshot_5.jpg If your network is 192.168.111.0/24, then 192.168.111.0 is a network address and cannot be used as a host address. There are fewer bridge MTUs on the device than MTU interfaces. Screenshot_...

Ca6ko

MTU issue when you have a mismatch you can't login to any secure sites like banks or financial companies. I completely agree. Most often such problems occur immediately after adding an interface with a lower MTU to the bridge(e.g. VPN), after which the MTU of the bridge becomes equal to this value....

Ca6ko

That's right it's not an 802.11 wifi device, it's a wireless Ethernet bridges, it's specifically designed for L2 traffic.
PS They usually require special permission from the authorities to use them

Ca6ko

Using wifi devices to transmit L2 traffic is a very bad idea. L3 traffic should be transmitted via wifi. In wifi, the maximum size of the data field is 2304 bytes.

Ca6ko

/caps-man rates
add basic=12Mbps name=rates_2Ghz supported=12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps

Why are you limiting the standard to 2003 only-G, why are you disabling the N standard 2008?

Ca6ko

When i use on Tplink cable or 5 ghz i get full speed 100 mbps. But when i use 2.4 ghz i get 1 mbps or more less.

Did I understand your description of the problem in the first post correctly?

Ca6ko

Disable the short guard interval, this will increase the stability of the link. The bridge is outdoors, not indoors.
Without radio parameters and network settings, it is difficult to give advice. Only L3 traffic should be transmitted over the radio bridge.

Ca6ko

Sometimes there is only remote access to the device

Ca6ko

Find the fix-space-6.47-smips.npk file on the net, copy it to your device and reboot it. After that there will be enough free space for updating. This problem appeared and was solved back in 2020-21. Apparently your device has been in the distributor's warehouse since then PS https://forum.mikrotik....

Ca6ko

so that means this sat+sxt combo is ~27dBi gain? No, that means the signal's about the same. Metal has one channel with -71 on SXT with two channels with the same level, and two channels is plus 3dB. There is one flaw in your metal data. The signal level from SXT to metal is -62dB and from metal to...

Ca6ko

Installing wifiwave2 moved all capsman settings to the wireless menu

Ca6ko

A relatively good signal is -60, -80...-75 is a poor or satisfactory signal.
The client starts looking for another access point when the signal strength is weaker than -68. MSC7 requires a signal stronger than -64

Ca6ko

Try changing the network connections. Mikrotik after netinstall has an IP address 0.0.0.0 connection problem was related to this. Something in the computer is blocking access.
Try to set the address 0.0.0.2 on your computer.

Ca6ko

It's just the winbox not displaying the information. I've had such cases, I don't remember the exact cause. But the point is that the winbox does not receive information from the device, so all fields are empty.
PS It's a network problem.

Ca6ko

These problems are related to the ISP's hardware settings. It has nothing to do with the Mikrotik.
Turn on the TP-Link NX510v to the ISP and connect the Mikrotik between the computer and the TP-Link NX510v and check the speed.

Ca6ko

and I make the bridge enable DHCP snooping and add ether1 & ether2 to this bridge. after this, I plug the ether-2 wire into the unmanageable switch and also plug ether-5 in the switch You made a loop by connecting Mikrotik 2 and 5 ports through a switch. The RSTP protocol breaks the loop and di...

Ca6ko

In the HAP AC device, the wlan1 interface operates at 2.4GHz and the wlan2 interface operates at 5GHz. Your ISP operates at 2462. In the HAP AX2, the interfaces work differently wlan1 works at 5GHz and wlan2 works at 2.4GHz. You need to apply all settings to the wlan2 interface. Show the complete me...

Ca6ko

/ip route
add disabled=no dst-address=10.10.0.100/24 gateway=wireguard routing-table=\
main suppress-hw-offload=no

Ca6ko

@elbantany
It looks like you didn't notice that the channels were swapped in AC and AX2. In AX2, 2GHz is wlan2, 5GHz is wlan1.

Ca6ko

You've had 36 link drops. There is a high probability that there is interference in the form of swaying tree branches, or the masts of access points are swaying. It is also possible that the link is disconnected due to radar detection. For stable operation in the 80 MHz band at maximum speed in the ...

Ca6ko

you can’t get them tight enough to a pole nor adjust azimuth.

This requires the use of a special mount
https://mikrotik.com/product/qm_x#fndtn-gallery

Ca6ko

I can help, but I didn't realize what was needed. There is such a table of translation of Ukrainian alphabet by Latin alphabet. Screenshot_12.jpg CP1251 It, except russian, also contains all symbols for other Slavic languages: Ukrainian, Belarusian, Serbian, Macedonian and Bulgarian. I can help only...

Ca6ko

Office1
/ip/address
add address=10.255.255.1/30 interface=wireguard1

/ip/address
add address=10.255.255.1/30 interface=Wireguard-HotSpot

Ca6ko

I have 11 Link downs

This number indicates how many times no clients have been connected to the interface. It is only relevant when there is a client that is permanently connected (radio bridge mode).
PS The screenshot shows just the moment when there are no registered clients.

Ca6ko

Try setting it up like this

Ca6ko

Judging by the fact that radio-name=BACKUP-1, you are using backups. Therefore, clear the configuration completely, as the work with routing tables has changed in v7.

Ca6ko

You need to firewall additionally block access to 8.8.8.8 through all other interfaces except the required ether1.
When you disable the ether1 interface, all routes associated with it are disabled.
As a test you can cut the connection between ISP1 and Switch1, everything will work as you wanted.

Ca6ko

Re-flash the device via netinstall and try again.
What device?
What version of ROS?

Ca6ko

These two models are even available on Mikrotik's website. It isn't. The SXT 5ac model has been out of production for a long time (about 5 years), it had a level 3 license. and a narrower radiation pattern than the SA Instead, the SXTsq 5 ac model is being produced. PS If you have license 4 then ev...

Ca6ko

If there are errors in the text of the netwatch script, its work may stop

Ca6ko

No need to configure firewall rules with /32 routes but you can if you want. Here is an example, the channel is configured through wlan1 at the moment interface wlan1 is not connected to the access point. If there is no blocked access to 1.0.0.1 through other interfaces, as you can see the route to...

Ca6ko

You are right, I don't need the recursive routing. In this case, set routes without using recursive routing. You need to additionally deny access to the test IP through any other interface than the desired one in the firewall. For example route add check-gateway=ping comment="Netwatch LTE"...

Ca6ko

Could someone help me understand this concept of routes on mikrotik so that my tunnel can work? You didn't ask the question clearly. You have not formulated the problem you are trying to solve with the GRE tunnel. You have a large knowledge gap in the basics of networks, in particular the routing s...

Ca6ko

What is the maximum number of active users?

The DHCP server does not work with users, it works with leases.
In ROS, it is limited only by the number of IP addresses that you set in the DHCP pool. And the capabilities of the device.

Ca6ko

its not roaming You put some kind of meaning in the concept of wifi roaming. From the station's point of view, it is roaming. If the station is roaming disabled, then the station will be connected to one access point and will not look for another access point until the connection is broken, only th...

Ca6ko

Connection List is useless... As you described the problem is solved exactly with the Connect list. The principle of the Wifi station holds on to the access point until the signal drops to -68. At this signal the station begins to look for an access point with better parameters if there is one it s...

Ca6ko

Thanks for the tip that rc 6 does not fix the problem. Tomorrow I plan to try a downgrade to 7.8
viewtopic.php?t=196170

Ca6ko

I expect someone from MikroTik will answer my question here. This is a technical forum where ordinary people write in their spare time. No one is obliged to answer you on the forums. +I think I described my problem very well. It's a simple question, even yes/no would help. I also think I have answe...

Ca6ko

AX2 7.9.2/7.10.rc5 clients can not connect to the wifi. There are Handshake errors in the logs. Configuration features included WPA2/WPA3 have virtual interfaces. /interface wifiwave2 channel add band=2ghz-ax disabled=no frequency=2412 name=channel1 width=20mhz add band=2ghz-ax disabled=no frequency...

Ca6ko

huawei_me909u_521_lte_lga_module_application_guide_english.pdf
12.GPS appliation scenarios

Ca6ko

maybe is time for Users to Make their own independent MUMs

In Moscow they are already conducting...

Ca6ko

https://wiki.mikrotik.com/wiki/Manual:System/GPS

Ca6ko

1. Enable/check all ports for ROMON
2. disable secrets on all devices for the test and check availability.
3. Check if the devices are visible through the IP neighbors.

Ca6ko

I have an hEX mikrotik routerboard що WAN працює на ether2***, а не на SFP(+) чи іншому гігабітному порту, коли маршрутизатор має змішані порти 100/1G (наприклад, rb2011). What does that have to do with it? The @villegas hex has all 1Gb ports. The reason why he cannot use the bandwidth of the wan p...

Ca6ko

I can wirelessly connect the hAP to 3rd party APs via wlan1/Station. I can connect my devices wirelessly to the hAP wlan2/AP. Both LAN and wlan2/AP give me IP addresses and I can ping the router but not the internet.

For such a case, you need to add wlan1 to the WAN interface list

Ca6ko

Draw a network diagram, specify the equipment and point out where the bottleneck, we will suggest solutions.
I haven't seen such a variant of channel aggregation yet ...

1 link isn't enough to use all the bandwith we have,

So you need to change the switch

Ca6ko

OP asked about USB-C "A device with a Type-C connector does not necessarily implement USB, USB Power Delivery, or any Alternate Mode: the Type-C connector is common to several technologies while mandating only a few of them." https://en.wikipedia.org/wiki/USB-C Many people are mistaken ab...

Ca6ko

Familiarize yourself with the power capabilities of USB. The regular USB2.0 output guarantees a current of 500mA which provides 2.5 watts of power. The USB3.0 guarantees 900 mA which provides 4.5 watts of power. Standard USB3.2 output power of 7.5W. The higher wattage is only provided by devices tha...

Ca6ko

I'm sorry, I don't quite understand you.

Ca6ko

You were told to reset to CAP mode. Then there is no need to configure anything at all Reset button The reset button has three functions: Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds). Keep holding for 5 more s...

Ca6ko

I can not make my mind to chose from those two POE swtiched. Which is please better? Which on would you chose? You didn't provide any criteria to choose from. 1. Number of devices, connection ports. 2. required POE standards, characteristics of the equipment to be connected 3. bandwidth requirements.

Ca6ko

No, it's RB2011.

Ca6ko

Here is my Network Home miniLab. SolidRack 1006
The attachment of the devices to the shelf is magnetic, using a metal plate and magnets from the HDD.

1 photo.jpg

2 photo.jpg

3 photo.jpg

4 photo.jpg

5 photo.jpg

Ca6ko

You can use the half from the RMK-2/10 kit and the half from the RB5009/L009 rackmount kit K-79. With a little bit of modification. Then you can use any 200mm form factor switch

Ca6ko

I miss the RB433's You'll get about the same on the RBM33G. I assume we are talking about the retransmitter in an inaccessible place? But I would suggest getting two ready-made devices with built-in antennas, like the LHG XL. Due to the high gain of the antennas you can reduce the output power of t...

Ca6ko

Mikrotik makes the SolidRack 10. But such a rack is not always suitable for small installations. I suggest to rename SolidRack 10 to SolidRack 1910 (19" 10U) and release a small version of SolidRack 1006 (10" 6U). Possible variants are 1010, 1008
I made myself one of these 1006.

Ca6ko

When set on ap, the master has to be set manually towards the correct frequency or the slave-station will not connect.
Right ?

Yes

Ca6ko

I have it working on a virtual

Ca6ko

Since the interfaces will work in turns, don't forget to increase the buffers of the interfaces to the required size. I would change the assignment of the interfaces to wlan access point mode on the physical interface wlan1, station mode on the virtual interface wlan3. This is assuming that the upli...

Ca6ko

You probably phrased your question poorly, since no one wants to answer you.
Look in the direction of the connection list
I don't think changing the signal level will help you much. The problem lies on another plane.

Ca6ko

Take a close look at the capabilities of the K-79
https://i.mt.lv/cdn/product_files/RB500 ... 210741.pdf

Ca6ko

You do not need to add a route separately. Just set the port of the mikrotik to which the Starlink is connected to an additional IP address from the network 192.168.100.0.0/24 any other than .1, the route will be created automatically.

Ca6ko

Now, if one of these notebooks is changed to a Static IP within the 192.168.0.xxx range, everything works fine. . on a notebook via wifi that has dhcp range I put static ip in the range 192.168.0.x and I could print perfectly. To rule out a wifi problem. On a computer with a cable connected, set st...

Ca6ko

Unifi transparent bridge mode enabled?
Try on a computer with a static IP address to change it to an address from the DHCP pool. If it works, the problem is with Unifi if not, the problem is with the printer.

Ca6ko

the shunt fed AM still radiates 5kw

Then use Mikrotik devices with a metal case QRT 5 ac or NetMetal ac² + mANT30 + Sleeve30.
.

the thick cable is shielded and grounded every 10 feet.

What prevents you from doing the same with twisted pair?

Ca6ko

need a radio that takes an antenna and can do so with 200-250 feet of shielded coax. The idea is utopian. What is the attenuation of your cable at 5GHz? Theoretically you could try GrooveA 52 ac/Metal 52 ac with the mANT30 antenna. But I think the cable attenuation will negate the results. But you ...

Ca6ko

Techsystem wrote Wed Apr 26, 2023 7:35 pm give an advise or explaination about how can i config this ... /ip firewall nat add action=src-nat chain=srcnat comment="defconf: masquerade" out-interface-list=WAN to-addresses=192.168.2.2 . Ca6ko wrote Fri Apr 28, 2023 10:40 am For mikrotik you ...

Ca6ko

Show the mikrotik configuration after applying my recommendations
viewtopic.php?p=999909#p999769

Ca6ko

It seems this is only applicable for UDP streams, not for TCP.

Ca6ko

There is a small undocumented specifics of using the btest program
Note how the maximum traffic generation capacity of the device's processor is determined

Screenshot_6.jpg

Screenshot_5.jpg

Ca6ko

My public IP address is 2XX.XX.XX.XX.

Your ISP probably has a problem

Ca6ko

viewtopic.php?p=908118

Ca6ko

You don't have a public address on the mikrotik so it has nothing to do with it. You have an Asus for Hairpin NAT. You don't understand the situation correctly and are therefore looking for the wrong solutions. Mikrotik's Hairpin NAT settings will allow you to access its external address 192.168.2....

Ca6ko

viewtopic.php?t=195178#p999650

Ca6ko

You can't change the network on the LTE modem, but you can on the router A. I recommend setting the low-use band to .200-250
such as 192.168.235.0/24 this will avoid similar problems in the future.

Ca6ko

To be completely sure that the problem is in the ROS configuration, do a UDP test from the computer and router to the public server bandwidth-test
viewtopic.php?t=104266

Ca6ko

Do builds for arm64 (my CCR2004) contain the CAPSMAN-controller too or only drivers?

contain the CAPSMAN-controller +drivers

can I run CAPSMAN and CAPSMAN-WifiWave2 on the same physical router?

no

can I simply run the cAPax with the "old" CAPSMAN?

no

Ca6ko

Hap ax lite has arm32.

L009 has ROS x32
PS
Looks like the L009 has 10" rack mounts or not?

Ca6ko

Lubricate with vegetable oil (I used sunflower oil) after a while the oil will be absorbed into the plastic and the antenna will hold tight.

Ca6ko

Why do you create several threads with the same problem.https://forum.mikrotik.com/viewtopic.php?t=195707 Your task is to make it as clear as possible to other users to ask a question and then get help. To do this, it is best to draw a network diagram. . yes you can pretend the 192.168.2.2 as the pu...

Search found 503 matches